New OEM Can Am Brake Switch Part Number: 705601250 Unsure on fitment? Please ask us we will help!
Brand NEW OEM BRP Genuine Transmission Drive Belt Will fit: Defender, Maverick Trail 1000/1000R Maverick Sport 1000/1000R Will also fit other machines. Must check part numbers to confirm fitment. Current Part Number: 417300551 Replaces 417300383 High performance drive belts calibrated to maximize your machine’s performance. Aramid tensile cords used in construction for extra long life and dependability, also delivers a consistent length. High tensile reinforced fiber elastomer undercords provide minimal dusting and long term flex life. Flexweave overcord for superior adhesion and crack resistance. Consistent performance during life of belt. Quality you can count on for optimum performance
OEM Snorkel kit, this raises the engine air intake well above the handlebars. The ECU is relocated to allow for CVT breather tubes to extend upward. This kit includes the brackets for the two plug type ECU found on ride by wire outlanders. With the tubes molded specifically for this application this is the cleanest kit you can install on your machine. Part number 715005999 Installation time is approximately 3.5 hours This snorkel kit is not compatible with the XT Handlebar Protector Kit (P/N 715000271) 715005999 instructions
2012-2018 G2 ATV Rear Differential Swap Kit Kit includes: Rear Differential, Rear driveshaft, Bolt and Washer. This kit includes a rear differential with: Tapered roller bearings Three bearings on the pinion gear 6 inch diameter ring gear Your choice of gear style, spiral bevel or straight cut. Both have the same 3.60 ratio as your current differential. Spiral Bevel Gears are sourced from the 2013-18 800 850 and 1000 XMR differentials. Current part number 705502546 Old part numbers: 705502178 & 705502090 Straight Cut gears are sourced from the 2019+ 650+ differentials. Current part number 705502808 The driveshaft included is an OEM shaft with the correct end yokes for your application. The differential end yoke will not use a wear ring, this has been done away with by BRP the yoke is what the pinion seal touches now. You will need to fill the differential with 250ml (8.4oz) of 75W-140 gear oil and transfer over your fill plug and washer. The torque spec on the driveshaft retaining bolt is 55ftlbs with thread locker applied. Some minor trimming on the brackets that surround the differential is required. These differentials have the provision for an ABS sensor, this is standard on euro models, for mud riders state side, you can fill this hole with RTV or leave it open. If you are running the silver protector ring on your axle, you will need to push the ring outward slightly. We choose to remove these dust covers as they tend to trap debris when run under water.
There are a few options for kits, please verify your differential uses this style of gears before ordering!
This will only fit six mounting hole differentials.
Late G1 Early G2 Standard Rear Differential Ring 36t and Pinion 10t gear set Pinion bolt size is M10, this may be different than what you are replacing.
OEM Rear Differential Gear set 10/36 Ring and Pinion gear set. The gears are straight cut as pictured. This kit should be installed by an experienced technician.
Open up the differential! Check for two bearings total (one on each side) on the ring gear. If you only have two proceed to the next measurement. Measure your outer diameter of your axle seals! They should measure close to 1 3/4? (47mm) To further verify fitment you can measure your pinion pilot shaft, this should be 9/16" (14mm) The pictures show this very clearly. Please take the time to measure your parts before buying this will save time and restocking fees.
Allows the installation of accessories with 16” base on LinQ racks. Tool-less installation and removal. Part number 715004960
Oring that replaces 705501880 Buna-N 70 Duro (NBR) This is used on 2014-19 Commander rear differential (without unlocking rear) pinion gears
One spark plug boot, this is used on many applications 2020 and older, if you are unsure on fitment, please contact us.
Part number 420265248
Replaces 710000041 and 420265240
New OEM Cylinder Head Gasket Fits Defender HD5 Outlander 450 and 850 Renegade 850 Will come as pictured Part number 420450340
Used- Good Condition, completely checked over and tested, works as it should OEM 2015 800, and 1000 Commander Short Wheel Base Electrical Harness This Electrical Harness is the Chassis Only Product Number: 710004332 Comes as Pictured
Sunburst yellow wrap around wind deflector set with mounting kit. Fits Outlander, Renegade, & DS450. Both are brand new. Part numbers 709402053, 709402054 & 715001378
New Genuine OEM Mounting kit sold separately Part number 709402053 709402054
