Brand New Moose Utility 13 Bolt CVT Cover Gasket
Works on 7 bolt covers also.
Part number 0935-1193
replaces: 420430127 420430126 420430124 420430123 420430120
Brand New Genuine OEM BRP logo sticker 20mm diameter Part number 516006224 replaces 219902677 704904616
Impact-absorbing rubber prevents bottoming-out of winch Prevents hook rattling when not in use A must-have for preventing damage to your winch fairlead Made in the U.S.A. 2 1/2″ Diameter 1 3/4″ Thick Part number 4505-0475
New G2 dual piston Right Rear brake caliper with OEM pads. Fits G2 Renegade and Outlander 2012-current Genuine OEM part. Part number 703500969
NEW Chrome Conical Taper M10 Lug Nut Set of 16 M10x1.25 thread size 60 Degree taper 14mm Hex head size, great for use with aftermarket wheels where socket space is a concern These will work on every Canam ATV since 2006 and most every Canam sxs Will not fit the Maverick X3 12mm wheel studs. Part numbers: 57-94121, ALUG14BX
OEM Air Filter for Gen 1 Outlander and Renegades. Larger style air filter found on 800R machines. OEM part number: 707800288
New MOOSE UTILITY DIVISION Hi-Performance Cooling Fan - 1300 CFM Fits on some G2 Oultander/Renegade and OG Maverick, please verify your current fan motor has four mounting holes. Will not fit XMR Outlander's Part number 1901-0712 Replacement fan motor fits in part numbers: 709200564 709200309 709200462
There are a few options for kits, please verify your differential uses this style of gears before ordering!
This will only fit six mounting hole differentials.
Late G1 Early G2 Standard Rear Differential Ring 36t and Pinion 10t gear set Pinion bolt size is M10, this may be different than what you are replacing.
OEM Rear Differential Gear set 10/36 Ring and Pinion gear set. The gears are straight cut as pictured. This kit should be installed by an experienced technician.
Open up the differential! Check for two bearings total (one on each side) on the ring gear. If you only have two proceed to the next measurement. Measure your outer diameter of your axle seals! They should measure close to 1 3/4? (47mm) To further verify fitment you can measure your pinion pilot shaft, this should be 9/16" (14mm) The pictures show this very clearly. Please take the time to measure your parts before buying this will save time and restocking fees.
Can Am Outlander 500 650 piston ring set New Genuine OEM Kit is only for one piston Current part number 420684384 Old part number 420684114
SHIPS FREE TO THE LOWER 48 STATES Fits 2012-18 G2 atv’s with non reservoir shocks. 25% stiffer over stock springs, great alternative to lift pucks. Pair these with the fox shocks for a nice ride! WE325123 WE325121
Dual USB Power Outlet Kit A simple upgrade kit, plug and play Product Number: 219400510 replaces the existing 12v power outlet on your machine: 710001248
OEM Canam Projector High Beam projector head light assembly with 9005 bulb. Brand NEW! High quality HELLA brand made in Austria. Fits many models please ask if you are unsure! Part Number 710002525
All Balls complete module, retaining nut and gasket This fits many G2 model ATVs please contact us if you have fitment questions. Part number: 1009-0139 47-1024 Replaces OEM numbers: 709000287 709000758- OUT OF STOCK
New Demon Heavy Duty Axle Front Left Fits: G2 2012-2018 ATV Outlander/Renegade 500 570 650 800R 850 1000 1000R Part number PAXL-3070HD Replaces OEM 705400756 703500823 705401943 705401115 705401384 705401947 705401704 Through years of research and development Demon Powersports has developed an axle that doesn’t burn a hole in your pocket and adheres to the highest quality standards. These axles are bigger, beefier, and stronger. Demon Heavy Duty Axles are built using larger CV joints and shafts, paired with our proprietary dual heat treatment process, and 4340 Chromoly Steel inner CV cage gives these the axles the edge it needs for superior strength and longevity. These axles also utilize a unique double plunge design which allows it to achieve higher articulation angles approximately, the axles are designed to slide on the bar splines allowing for 1.5 inches of travel and 40° articulation over terrain on the inboard joint. The outboard joint can travel 0.5inches and swing from 45°-47° depending on the model. The Demon heavy duty axles are equipped The TPEE (Thermoplastic polyester elastomer) boots which are stronger, stiffer, more fatigue resistant, puncture resistant, and more temperature resistant than a standard OEM boot. Axles use molybdenum grease to provide low friction and smooth motion. Trust in Demon Heavy Duty Axles to keep you riding!! • 15%-20% increase in diameter compared to regular axle • Inner cage made up of 4340 chromoly steel • Dual heat treated high strength chromoly steel shaft • Thermoplastic polyester elastomer (TPEE) Boot • 10%-15% increase in CV joint size compared to regular joints • Wider articulation angles • Dual plunge design prevents axle from binding • Packed with high load molybdenum grease Precision CNC machined • Can Fit 1.5”- 5” Bracket lift of particular brands/ All Portal Gear Lifts / 1.5”- 5” A-arms of particular brands • 1-year ltd warranty 
Mohawk Dash for Can-Am Renegade Will work some 2021+ Renegades Clean way to hide custom snorkels Factory OEM part 705015170- OUT OF STOCK
New Genuine OEM Handlebar End Cap Part number 709400449 
OEM oring commonly used on distance ring on gearbox input shaft. 420631610 replaces 420631615
Six Weights 21 gram each for CVtech Trailbloc Primary Part numbers: 0935-2054 or 0901-7118- OUT OF STOCK
Air Filter for G1 Outlander and Renegades. Replaces OEM 707800174 Fits 500, 650, and 800HO NON-R 800 engines, from 2006 – 2012. Bonded, two-layer .65" foam designed for maximum protection and airflow Coarse outer foam traps large particles while fine inner foam catches the finest dust With the precision pre-oiled air filter, there is no excess oil to rob horsepower, and no dry spots endangering your engine Made in the U.S.A. - OUT OF STOCK
NEW Genuine OEM Fuel/Gas Cap Fits most every Can-am ATV Renegade or Outlander Part Number: 513033025 
SHIPS FREE TO THE LOWER 48 STATES- LED dimmer facilitates reading temperature settings.
- 4 temperature settings with individual controls for thumb and grips.
- Returns to previous heat setting.
- One-touch shutdown.
- Wiring Harness (710004567) required for installation, on G2L and G2S (except 1000R and T category models) G2 Outlander does not require the harness.
NEW OEM Exhaust Muffler Gasket This slides on to the header pipe, then muffler slides over it. 2" outer diameter 1.77" inner diameter 1" wide Part number 707600430
New Genuine OEM Intake neck for Outlander 1000, Renegade 1000, Commander 1000 and Maverick 1000 Turbo Old part number 420267040 420267041 Current part number 420267042
NEW OEM BRP OIL PUMP
Part number 420256348 replaces 420256347
New Demon Heavy Duty Axle Rear Left Fits: 2019+ ATV Outlander/Renegade 650 850 1000R Part number PAXL-3064HD Replaces OEM 705502710 705503025 705502712 Through years of research and development Demon Powersports has developed an axle that doesn’t burn a hole in your pocket and adheres to the highest quality standards. These axles are bigger, beefier, and stronger. Demon Heavy Duty Axles are built using larger CV joints and shafts, paired with our proprietary dual heat treatment process, and 4340 Chromoly Steel inner CV cage gives these the axles the edge it needs for superior strength and longevity. These axles also utilize a unique double plunge design which allows it to achieve higher articulation angles approximately, the axles are designed to slide on the bar splines allowing for 1.5 inches of travel and 40° articulation over terrain on the inboard joint. The outboard joint can travel 0.5inches and swing from 45°-47° depending on the model. The Demon heavy duty axles are equipped The TPEE (Thermoplastic polyester elastomer) boots which are stronger, stiffer, more fatigue resistant, puncture resistant, and more temperature resistant than a standard OEM boot. Axles use molybdenum grease to provide low friction and smooth motion. Trust in Demon Heavy Duty Axles to keep you riding!! • 15%-20% increase in diameter compared to regular axle • Inner cage made up of 4340 chromoly steel • Dual heat treated high strength chromoly steel shaft • Thermoplastic polyester elastomer (TPEE) Boot • 10%-15% increase in CV joint size compared to regular joints • Wider articulation angles • Dual plunge design prevents axle from binding • Packed with high load molybdenum grease Precision CNC machined • Can Fit 1.5”- 5” Bracket lift of particular brands/ All Portal Gear Lifts / 1.5”- 5” A-arms of particular brands • 1-year ltd warranty
Fits all 500, 650, 800, 800R, 570, 850, 1000, 1000R and 1000R turbo Mavericks Outlanders, Renegades, and Commanders. Replaces OEM part numbers 715000302, 422280360, 715900212, and 422280364. This will not fit: Defenders, Maverick X3 or Maverick Sport/Trail Part number MMCA302 This belt is built specifically for the straight mud rider that needs a ton of belt squeeze to stop from slipping the belt. The specific compounds in this belt make it instantly grab when the clutching and tune are correct. Note: This blend of compounds and thickness will build more heat at higher speeds, so we recommend keeping it under 35mph Mud Monster Belt Line Higher strength compared to OEM and aftermarket drive belts. Mud Monster belts have been developed with the 2nd Generation compound called DUMAX2 for added strength, flexibility, and heat resistance. You can squeeze this belt a lot harder for more tuning possibilities and less slippage. Maximum under-cord stiffness allows the belt to flex for rotational efficiency and running cooler temperatures Built thicker when possible for more belt to sheave adhesion. Built for extreme abuse, and excessive shock load. Handles higher temps than OEM Built with Aramid fiber cord to eliminate stretching like a Polyester cord. Made in the USA!
One spark plug boot, this is used on many applications 2020 and older, if you are unsure on fitment, please contact us.
Part number 420265248
Replaces 710000041 and 420265240
Brand new OEM left side rear view mirror. Mirror Will fit all CAN AM Outlander or Renegade models 2006+
New Demon Heavy Duty Axle Rear Right (throttle side) Fits: 2019+ ATV Outlander/Renegade 650 850 1000R Part number PAXL-3065HD Replaces OEM 705502711 705502713 705503024 Through years of research and development Demon Powersports has developed an axle that doesn’t burn a hole in your pocket and adheres to the highest quality standards. These axles are bigger, beefier, and stronger. Demon Heavy Duty Axles are built using larger CV joints and shafts, paired with our proprietary dual heat treatment process, and 4340 Chromoly Steel inner CV cage gives these the axles the edge it needs for superior strength and longevity. These axles also utilize a unique double plunge design which allows it to achieve higher articulation angles approximately, the axles are designed to slide on the bar splines allowing for 1.5 inches of travel and 40° articulation over terrain on the inboard joint. The outboard joint can travel 0.5inches and swing from 45°-47° depending on the model. The Demon heavy duty axles are equipped The TPEE (Thermoplastic polyester elastomer) boots which are stronger, stiffer, more fatigue resistant, puncture resistant, and more temperature resistant than a standard OEM boot. Axles use molybdenum grease to provide low friction and smooth motion. Trust in Demon Heavy Duty Axles to keep you riding!! • 15%-20% increase in diameter compared to regular axle • Inner cage made up of 4340 chromoly steel • Dual heat treated high strength chromoly steel shaft • Thermoplastic polyester elastomer (TPEE) Boot • 10%-15% increase in CV joint size compared to regular joints • Wider articulation angles • Dual plunge design prevents axle from binding • Packed with high load molybdenum grease Precision CNC machined • Can Fit 1.5”- 5” Bracket lift of particular brands/ All Portal Gear Lifts / 1.5”- 5” A-arms of particular brands • 1-year ltd warranty
For use with all BRP turn key type ignition switches. Will not fit RFID type ignitions. Simply cut off the old harness and use the included butt connectors or solder the connections to the new pigtail. Be sure to match up one wire at a time when installing, this helps avoid switching wire orientation as the wires are not color coded. The wires are 6” long so it can be fixed inside the headlight pod Sold each; includes butt connectors and zip ties Part number 2120-0943
New G2 dual piston front left brake caliper with OEM pads. Fits G2 Renegade and Outlander 2012-2019 Genuine OEM part. Part number 705600862
New OEM Can Am Factory Helix If you are unsure about fitment, contact us. We are here to help! Current Number 420280701 Replaces 420280700
CVTech Trailbloc Nut for ribbed style clutches This is the large nut that retains the outer clutch to the inner. M22 diameter Part number 0980-1015
New Genuine OEM Mounting kit sold separately Part number 709402053 709402054
Gold / Red / Red 300-900 0951-1019
CVtech Spring Gold/Pink/Pink 400-1200 rate 0951-1025
