New aftermarket 91mm bore piston and cylinder kit with gaskets rings wrist pins and circlips 10.5:1 compression ratio This is a ready to bolt on kit Fits: Commander 1000 ATV 1000/1000R Defender HD10 and DH9 Maverick Sport 1000 Please note this kit will not fit the SXS 1000R due to the lower compression ratio. No dowel pins included, you will need to transfer these from your engine Replaces OEM Part Numbers: 420685242 420685248 420623568 420623566 420630210 420245436 420216351 420685244 420296774
NEW Genuine Can-am Rear Prop Shaft for G1 STD single seat machines WILL NOT FIT MAX. This will work with 2006-2011 500 650 800 800R, Outlander or Renegade and 2012 Outlander 500 650 or Renegade 500. The picture is what you will get. We install the wear ring and deflector ring for fast install. Current Part number: 703500801 Previous numbers: 703500767 703500719 705500816 703500704
NEW OEM Radiator for 2012+ G2 Can-Am Outlander and Renegade ATV’s Should fit all engines and submodels, including XMR Part number 709200286
There are a few options for kits, please verify your differential uses this style of gears before ordering!
This will only fit six mounting hole differentials.
Late G1 Early G2 Standard Rear Differential Ring 36t and Pinion 10t gear set Pinion bolt size is M10, this may be different than what you are replacing.
OEM Rear Differential Gear set 10/36 Ring and Pinion gear set. The gears are straight cut as pictured. This kit should be installed by an experienced technician.
Open up the differential! Check for two bearings total (one on each side) on the ring gear. If you only have two proceed to the next measurement. Measure your outer diameter of your axle seals! They should measure close to 1 3/4? (47mm) To further verify fitment you can measure your pinion pilot shaft, this should be 9/16" (14mm) The pictures show this very clearly. Please take the time to measure your parts before buying this will save time and restocking fees.
1652 G2 Standard Rear Differential Rebuild Kit Please note, application alone is not accurate enough, please measure your parts before ordering! There are a few options for rebuild kits, please measure your parts before ordering!! OEM Rear Differential Gear set 10/36 Ring and Pinion gear set. The gears are straight cut as pictured. Paired with high quality aftermarket ball bearings along with double lip axle seals. If your differential has tapered roller bearings, this will not fit. This kit should be installed by an experienced technician. Shims are included as the gears will need to be set up in your cases. Note: the O rings are not included, this is a cost savings measure as they are generally reusable. This kit will only fit six mounting hole differentials. Measure your outer diameter of the pinion seal, it should measure 2 3/4" (70mm) Measure your outer diameter of your axle seals! They should measure close to 2 1/16″ (52mm) To further verify fitment you can measure your pinion pilot shaft, this should be 5/8″ (16mm) Please take the time to measure your parts before buying this will save time and restocking fees. Fits 2015 and newer G2 style ATV 500/570/650/800/850/1000/1000R NON-XMR style REAR differential. 570/650 XMR machines do not have the true XMR differential.
SHIPS FREE TO THE LOWER 48 STATES New OEM XMR Rear Differential Gear set, 10/36 Ring and Pinion gear set, Timken, Dichtomatik or SKF seals, NTN or IKO pilot bearing , OEM shim kit and OEM bearings Fits the larger style 800/850/1000/1000R XMR style REAR differential first seen on the 2013 Outlander 1000 XMR. This gear set will not install into 650 xmr and 570 xmr differential cases. Please see our other listings for those. This is a common part to swap on to generation 2 atvs. We do sell complete kits to do so, please check out our other listings. Part number 703500870
New OEM 2019+ rear differential gear set, 10/36 tooth straight cut ring and pinion gear set, Timken seals, NTN or IKO pilot bearing , OEM shim kit and OEM bearings along with a new bolt and washer to retain the driveshaft. BRP claims 25% increase in load capacity on this gear set vs the spiral cut xmr final drive units (rear differentials) from 13-18 models. Fits differential part numbers: 705502808, 705502546, 705502178, 705502090 703501031 705501550 705501556 705501557
New Aftermarket 1000/1000R Crankshaft with Connecting rods and bearings. No core needed, ready to install. *Will not fit Defender Maverick Sport/Trail* Replaces OE parts: 420219735 420219736 420217556 420217559 420641477 420641475 420233726- OUT OF STOCK
G2 dual piston brake calipers with pads. Genuine OEM parts. This set of three calipers will fit G2 Renegade and Outlander 2012+ Part numbers 705600861 705600862 705600859 Cleaned greased and ready to install. 
SHIPS FREE TO THE LOWER 48 STATES
Late G1 Early G2 Standard Rear Differential Rebuild Kit
There are a few options for rebuild kits, please measure your parts before ordering!!
OEM Rear Differential Gear set 10/36 Ring and Pinion gear set. The gears are straight cut as pictured.
Paired with high quality aftermarket bearings along with double lip axle seals.
This kit should be installed by an experienced technician. Ring gear shims are included as the gears will need to be set up in your cases, the pinion shims should remain unchanged
Note: the O rings are not included, this is a cost savings measure as they are generally reusable.
There are a few options for kits, please verify your differential uses this style of gears before ordering! This will only fit six mounting hole differentials.
Open up the differential! Check for two bearings total (one on each side) on the ring gear. If you only have two proceed to the next measurement.
Measure your outer diameter of your axle seals!
They should measure close to 1 3/4" (47mm)
To further verify fitment you can measure your pinion pilot shaft, this should be 9/16? (14mm)
The last pictures show this very clearly. Please take the time to measure your parts before buying this will save time and restocking fees.
- OUT OF STOCK
NEW OEM G2S Snorkel Kit for 2021+ G2 Renegade with larger display, if you have fitment questions please send us a picture of your speedometer and we will help. Part number 715007083 All hardware is included, instructions are online. We can email them if you have trouble finding them. Please note you will need to trim some parts on your machine, to install this kit. This is outlined in the instructions very clearly. This kit raises the engine intake, CVT intake and CVT exhaust. This is a must for an extreme mud rider. 
Set of four Moose gas shock kit for G1 Outlander 650/800 or Renegade 500/800 These shocks are the same length on all four corners, you may notice a slight lift, more so on a well used machine. *Please note these will not work in place of struts found on the Outlander 400/500 machines. Features: Moose gas shocks offer long term consistent performance over stock oil only damped shocks 10% stiffer springs provide a better ride and higher load capacity Works great on the front to better support your snowplow and on the rear when hauling cargo Smooth black color blends perfectly on your machine Direct bolt-on replacement: pre-installed spring allows for quicker setup P/N13102146X4
Have Questions?
Our staff is available to answer questions
canampartsguy@gmail.com
1340 Okray Ave.
Plover, WI 54467
jared@canampartsguy.com
Cant find What you're looking for?
Visit our 
store!
2016 Can Am Parts, LLC. All rights reserved.