High quality aftermarket Timken or SKF axle oil seal. Fits ATV rear differentials 2015-current, some UTV’s To be 100% sure on fitment, measure your outer diameter on your seal, it should read 52mm This seal has a 30mm inner diameter 52mm outer diamter and is 8mm thick. Replaces OEM 705501556 Order qty two per machine.
2012-2018 G2 ATV Rear Differential Swap Kit Kit includes: Rear Differential, Rear driveshaft, Bolt and Washer. This kit includes a rear differential with: Tapered roller bearings Three bearings on the pinion gear 6 inch diameter ring gear Your choice of gear style, spiral bevel or straight cut. Both have the same 3.60 ratio as your current differential. Spiral Bevel Gears are sourced from the 2013-18 800 850 and 1000 XMR differentials. Current part number 705502546 Old part numbers: 705502178 & 705502090 Straight Cut gears are sourced from the 2019+ 650+ differentials. Current part number 705502808 The driveshaft included is an OEM shaft with the correct end yokes for your application. The differential end yoke will not use a wear ring, this has been done away with by BRP the yoke is what the pinion seal touches now. You will need to fill the differential with 250ml (8.4oz) of 75W-140 gear oil and transfer over your fill plug and washer. The torque spec on the driveshaft retaining bolt is 55ftlbs with thread locker applied. Some minor trimming on the brackets that surround the differential is required. These differentials have the provision for an ABS sensor, this is standard on euro models, for mud riders state side, you can fill this hole with RTV or leave it open. If you are running the silver protector ring on your axle, you will need to push the ring outward slightly. We choose to remove these dust covers as they tend to trap debris when run under water.
This Product replaces the stock snorkel Mohawk prefilter screen. This prevents any mud clogging up and still allows air to flow into the snorkels. Made in USA Replaces OEM 705010922 to be installed in OEM Mohawk riser 705009685
NEW AFTERMARKET STARTER VTWIN Will come as pictured Part Numbers: 420684560 420684562 420684568 420684566
Brand New Genuine OEM XPS Full Synthetic Oil Change Kit. Ultra convenient “all in one” kit saves time and money. For Can-am off road vehicles with 500cc or larger Rotax engines. Excludes Traxter and Quest. Not compatible with Maverick X3 Includes 2 quarts plus 1 16 fl oz of 4T synthetic oil 0W40, 0-rings, rotax oil filter, and copper washer for old style and new style drain plugs. May not ship in original box Part Number: 779259
SHIPS FREE TO THE LOWER 48 STATES New OEM XMR Rear Differential Gear set, 10/36 Ring and Pinion gear set, Timken, Dichtomatik or SKF seals, NTN or IKO pilot bearing , OEM shim kit and OEM bearings Fits the larger style 800/850/1000/1000R XMR style REAR differential first seen on the 2013 Outlander 1000 XMR. This gear set will not install into 650 xmr and 570 xmr differential cases. Please see our other listings for those. This is a common part to swap on to generation 2 atvs. We do sell complete kits to do so, please check out our other listings. Part number 703500870
1652 G2 Standard Rear Differential Rebuild Kit Please note, application alone is not accurate enough, please measure your parts before ordering! There are a few options for rebuild kits, please measure your parts before ordering!! OEM Rear Differential Gear set 10/36 Ring and Pinion gear set. The gears are straight cut as pictured. Paired with high quality aftermarket ball bearings along with double lip axle seals. If your differential has tapered roller bearings, this will not fit. This kit should be installed by an experienced technician. Shims are included as the gears will need to be set up in your cases. Note: the O rings are not included, this is a cost savings measure as they are generally reusable. This kit will only fit six mounting hole differentials. Measure your outer diameter of the pinion seal, it should measure 2 3/4" (70mm) Measure your outer diameter of your axle seals! They should measure close to 2 1/16″ (52mm) To further verify fitment you can measure your pinion pilot shaft, this should be 5/8″ (16mm) Please take the time to measure your parts before buying this will save time and restocking fees. Fits 2015 and newer G2 style ATV 500/570/650/800/850/1000/1000R NON-XMR style REAR differential. 570/650 XMR machines do not have the true XMR differential.
NEW Bearing and Seal Kit for Can-Am Outlander and Renegade Rear Trailing Arms
They fit G2 Models (2012+)
Replaces part numbers 293350145 706000826 293200132 293200144
This is enough bearings and seals to do both rear arms (some newer models only use half the bearings)
These are high quality KOYO bearings and SKF/Dichtomatik seals.
New OEM can-am input or output seal for small gear boxes You will need two per gearbox. 32mm inner diameter 47mm outer diameter 7mm thick Current Part Number 420950089 Replaces Part Number 420950087
Can-am Rear G2 2012 and newer prop shaft. All New All OEM Shaft OEM U-joints, with OEM gearbox seal protector installed. Correct shaft for Single Seat (SWB) 2012-14 1000 Outlander or Renegade with 1000 XMR rear differential. WILL NOT WORK ON 2015 Outlander 1000/1000R and newer as these have the smaller gearbox. Direct replacement for 2016-Current Renegade 1000R XMR **Please note, this is the most updated shaft and does not require a wear ring on the differential side of the shaft. The last two pictures illustrate this.** 20 Spline Gearbox side yoke 20 Spline Differential side yoke Current Part number: 703500990 Previous Part number: 703500928 703500901
SHIPS FREE TO THE LOWER 48 STATES Fits all 500, 650, 800, 800R, 570, 850, 1000, 1000R and 1000R turbo Mavericks Outlanders, Renegades, and 2020 & Prior Commanders. Replaces OEM part numbers 715000302, 422280360, 715900212, and 422280364. This will not fit: Defenders, Maverick X3 or Maverick Sport/Trail Gates Part number 30R3750 Do not confuse this with the carbon or standard g-force, this is the newly developed for the 2020 season.DON’T BREAK YOUR BELT. BREAK IT IN.FEATURES AND BENEFITS Designed for the most demanding, turbo-charged off-road CVT applications. With Gates proprietary materials and design, G-Force™ RedLine™ CVT belts handle extreme temperatures with excellent heat recovery, while maximizing load and torque capacity ― making it one of the most efficient CVT belts currently on the market.- First on the market to utilize Ethylene Elastomer compound to address the needs of larger SxS and high-horsepower ORVs in tough riding conditions.
- Next-generation EE compound offers maximum transverse stiffness and heat resistance, resulting in higher load capacity, higher peak torque capacity, less “heat fade” and less speed loss.
- Delivers 75% greater dynamic axial stiffness on average, up to 50% lower speed losses and better recovery from temperatures up to +170°C (+338°F) without power loss.
- Unmatched Temperature Capability – Runs cooler, resists glazing for better recovery and reduced cracking/chunking out after running at temps exceeding +149°C (+300°F).
- Extended Belt Life – Belt life increased 100-300% versus aftermarket competitive belts in severe duty lab test conditions and in field testing.
- Higher Power Capacity – Reduced speed (rpm) loss by 50% under high loads and increased load capacity by >10% compared to other aftermarket belt.
If you don’t break the belt in properly, you’ll find yourself shredding the belt instead of the terrain. In fact, most powersports belt failures can be attributed to improper break-in and clutch adjustment – or not breaking in the belt at all. Follow these steps to ensure the best performance and longest life from your G-Force™ belt.
1. Clean the clutches according to manufacturer specifications and clean the sheaves with a Scotch-Brite™ pad. Remove old belt residue, glazing, oils, and debris with alcohol or acetone on the clutch sheave area. Be sure your breather tubes are free of any belt material (broken belt material gets everywhere)
2. Install and Break It In. Perform two heat cycles (10-15 minutes each) at +27°C (+80°F) at 30-40 mph (2-wheel drive) with cover installed. Bring the belt temperature down to normal operating temperatures, then shut down and let cool for 30 minutes. Repeat the process a second time. If belt installation is at a temperature of +16°C (+60°F) or below, perform two heat cycles in 20 minutes at 30-40 mph (2-wheel drive) with cover installed. Bring the belt temperature down to normal operating temperatures, then shut down and let cool for 30 minutes. Repeat the process a second time. Conservatively run through the entire shift range, without exceeding ¾ throttle. Bring the belt back to normal operating temperature (15 minutes) then shut down and completely cool the belt for 30 minutes. Repeat the process.
New XPS SAE 75W-90 and 75W-140 Synthetic Gear Oil Kit. Enough to do a complete service on the front differential, rear differential, and gear box 1 U.S QT 946ml per bottle Listing is for 2 Quarts. See your owners manual before ordering to make sure you order the correct weight for your Can Am Part number 779160 and 779158
Have Questions?
Our staff is available to answer questions
canampartsguy@gmail.com
1340 Okray Ave.
Plover, WI 54467
jared@canampartsguy.com
Cant find What you're looking for?
Visit our 
store!
2016 Can Am Parts, LLC. All rights reserved.