- OUT OF STOCK
NEW OEM Brake Line Fits 2012-17 Renegade 500 570 800R 1000 and 1000R Current part number 705601489 Replaces 705601123 705601060 This connects the front master cylinder to the front calipers. Brake lines on 2012+ and newer Can-am ATVs are known to be difficult to bleed, it is best to set some time aside to bleed it multiple times to get a firm lever. 
Part number 0950-1011
This isolates the spring from the one way bearing on a trail bloc primary clutch.
Measurements as shown
Can-am Rear Driveshaft G2 2019+ G2 Renegade 1000R base, XXC or XMR All New All OEM Shaft OEM U-joints, with OEM gearbox seal protector installed. **Please note, this is the most updated shaft and does not require a wear ring on the differential side of the shaft. The last two pictures illustrate this.** 20 Spline Gearbox side yoke (fits large type gearboxes) 20 Spline Differential side yoke (fits fits 705502808/705502546 rear differential) Current Part number: 703500990 Previous Part number: 703500928 703500901
Updated Can-am Rear G2 Driveshaft Fits: 2019+ Outlander 1000R (excluding MAX and XMR) 2019+ Outlander 650/850 (excluding MAX) 2019+ Renegade 650/850 All new all OEM Shaft OEM U-joints. OEM protector ring installed Gearbox side yoke swapped to 18 spline Current Part number: 703500988 Previous Part number: 703500858 703500931 If you have a 2019+ 570 short wheel base single rider, this may be the correct shaft for your application, the parts fiche may not show the correct part number. You will need to measure the outer diameter of your rear differential's pinon seal, this shaft will only work with machines that have a 80mm pinion seal. If you measure 70mm you will need 703500986. 20 spline differential side yoke (fits 705502808/705502546 rear differential) 18 spline gearbox side yoke (small gearbox size) No wear ring needed, the deferential side yoke is machined to the outer diameter that a wear ring would be.
SHIPS FREE TO THE LOWER 48 STATES OEM BRP Heated Grips and Thumb kit.- LED dimmer facilitates reading temperature settings. 4 temperature settings with individual controls for thumb and grips. Returns to previous heat setting. One-touch shutdown. Compatible with Intelligent Throttle Control (ITC). Wiring Cable (710004567) is required for installation on G2 650 and G2L 570.
All Balls complete module, retaining nut and gasket This fits many G2 model ATVs please contact us if you have fitment questions. Part number: 1009-0139 47-1024 Replaces OEM numbers: 709000287 709000758
Brand New Moose Utility 13 Bolt CVT Cover Gasket
Works on 7 bolt covers also.
Part number 0935-1193
replaces: 420430127 420430126 420430124 420430123 420430120
Rugged wheels spacers are made from T6061 aluminum alloy and are precisely CNC machined for accurate dimensions. Spacers can be direct bolt on and can use OEM studs. If you are looking to widen the stance of your machine, clear larger tires or get some new wheels. These spacers are just what you need. These spacers are sold as a pair. One inch thick The bolt pattern is 4x137mm M10 studs Part number PAWS-1035
Rugged wheels spacers are made from T6061 aluminum alloy and are precisely CNC machined for accurate dimensions. Spacers can be direct bolt on and can use OEM studs. If you are looking to widen the stance of your machine, clear larger tires or get some new wheels. These spacers are just what you need. These spacers are sold as a pair. 1.5 inch thick The bolt pattern is 4x137mm M10 studs Part number PAWS-1036
Rugged wheels spacers are made from T6061 aluminum alloy and are precisely CNC machined for accurate dimensions. Spacers can be direct bolt on and can use OEM studs. If you are looking to widen the stance of your machine, clear larger tires or get some new wheels. These spacers are just what you need. These spacers are sold as a pair. Two inch thick The bolt pattern is 4x137mm M10 studs Part number PAWS-1037
NEW OEM BRP Coupler This is found on many machines, 18 spline exterior No need for a wear ring on this coupler. Part number 705401969 Replaces 703500678 705400149 705500201
New OEM BRP secondary spring. Found on many 1000/1000R and 850 models. Current Part number 420638040 Replaces 420238177- OUT OF STOCK
NEW OEM Speedometer trim found on Renegade XMR models. Part number 705015189 
New NGK Spark Plug 93444
OEM part number 715900352
NGK part number LMAR8D-J
These spark plugs work in 2015+ Outlander/Renegade 450 850 and 1000R also fits Defender HD5
Shell
Thread Diameter: 10mm
Thread Pitch: 1.0mm
Seat Type: Gasket
Reach: 26.5mm (1.04″)
Hex Size: 9/16″ (14mm)
Terminal Type: Solid
Gap: .031″ (0.8mm)Center Electrode
Material: Nickel
Type: Standard
Size: 2.5mm
Projection: ProjectedGround Electrode
Material: Nickel
Type: Multi-GroundSpecifications
Resistor: Yes
Resistor Value: 5k Ohm
Heat Range: 8
Torque Specs: Aluminum: 7.2-8.7 lb. ft.
NEW OEM Shock Bushing for base black body hydraulic type shocks. These will fit: 2020 and prior Commanders 800 800R 1000 1000R G1/G2 Outlanders 400 450 500 570 650 800HO 800R 850 1000 1000R Oem part number 715900122
BOYESEN SUPERCOOLER WATER PUMP Cover and Impeller Kit Increased coolant flow at all rpm ranges Patented Nautilus-style impeller for hydrodynamic efficiency Color/Finish: Black, Powder-Coated Material: Aluminum Model: Supercooler Part number 850709 WPK-80AB Replaces OEM 420822750, 420622020 and 420622022 This is the style with the larger output nipple roughly 1 inch in outer diameter.
NEW Speed Sensor Quad Logic brand Will fit 2006-Current Outlander, Renegade, Maverick, Maverick X3, Commander, and Defenders 2210-0568 500-1024 Replaces OE Numbers 420265621, 420265622, 420265624, 420265625, 420265626, 420265629, 707000745 and 711265622
Connecting Rod Bolt for 650 800 V twin Engines This is the OEM bolt with a size of M8x1 Part number 420641640 420641645- OUT OF STOCK
Made in the USA Specialized ATV, made some strong, tough rods that will hold up to whatever kind of riding you like. 6061 Billet Rods with 5/8 heim joints and all the needed hardware to install. 1 year warranty from date of purchase, directly from SPATV 1 set comes with 2 tie rods and complete assembled heims and hardware. Fits G2 Outlanders and Renegades 2012+ (even the wider 2019+ machines) 
Specialized ATV HD Front Drive Shaft Fits G2 ATVs Replaces OEM part numbers: 705400913 705401032 Ships as pictured 25mm diameter shaft, this is huge compared to the OEM part. MADE IN USA
Set of four Bronco gas shock kit for G2 2012-2018 Outlander 500/570/650/800/800R/850/1000/1000R or Renegade 500/570/800R/850/1000/1000R
These shocks are the same length on all four corners, you may notice a slight lift, more so on a well used machine.
*Please note these will not work on the wider 2019+ ATVs.
Features:
Bronco gas shocks offer long term consistent performance over stock oil only damped shocks
10% stiffer springs provide a better ride and higher load capacity
Works great on the front to better support your snowplow and on the rear when hauling cargo
Smooth black color blends perfectly on your machine
Direct bolt-on replacement: pre-installed spring allows for quicker setupP/N AU-04340 AU-04440
CVtech Trail Bloc Primary Clutch with HD retaining bolt, calibrations are for ATVs not UTVs Solid upgrade over the factory unlocked primary clutch, this is a straight bolt on replacement. Locked sheaves, smaller one-way diameter and more belt grip. This is a great clutch for riders looking for a performance upgrade. This comes preset, some fine tuning may be required to get this 100% Many find these settings to be spot on. We will provide assistance in fine tuning for your riding style. Please allow additional 1-2 day handling time.
New Demon Heavy Duty Axle Front Left (opposite throttle side) Fits: 2019+ ATV Outlander/Renegade 650 850 1000R Part number PAXL-3062HD Replaces OEM 705402237 705402235 Through years of research and development Demon Powersports has developed an axle that doesn’t burn a hole in your pocket and adheres to the highest quality standards. These axles are bigger, beefier, and stronger. Demon Heavy Duty Axles are built using larger CV joints and shafts, paired with our proprietary dual heat treatment process, and 4340 Chromoly Steel inner CV cage gives these the axles the edge it needs for superior strength and longevity. These axles also utilize a unique double plunge design which allows it to achieve higher articulation angles approximately, the axles are designed to slide on the bar splines allowing for 1.5 inches of travel and 40° articulation over terrain on the inboard joint. The outboard joint can travel 0.5inches and swing from 45°-47° depending on the model. The Demon heavy duty axles are equipped The TPEE (Thermoplastic polyester elastomer) boots which are stronger, stiffer, more fatigue resistant, puncture resistant, and more temperature resistant than a standard OEM boot. Axles use molybdenum grease to provide low friction and smooth motion. Trust in Demon Heavy Duty Axles to keep you riding!! • 15%-20% increase in diameter compared to regular axle • Inner cage made up of 4340 chromoly steel • Dual heat treated high strength chromoly steel shaft • Thermoplastic polyester elastomer (TPEE) Boot • 10%-15% increase in CV joint size compared to regular joints • Wider articulation angles • Dual plunge design prevents axle from binding • Packed with high load molybdenum grease Precision CNC machined • Can Fit 1.5”- 5” Bracket lift of particular brands/ All Portal Gear Lifts / 1.5”- 5” A-arms of particular brands • 1-year ltd warranty
OEM Rotax Cylinder Base gasket Fits many Canam ATVs Outlander/Renegade 450 or 850 Unsure on fitment? Please ask! Part number 420450330
New Air filter made by All Balls Racing. This is an OEM replacement filter for early G1 500 650 800HO Outlander or Renegade Please note this will not fit the 800R ATVs Replaces OEM 707800174
New Demon Heavy Duty Axle Front Left Fits: G2 2012-2018 ATV Outlander/Renegade 500 570 650 800R 850 1000 1000R Part number PAXL-3070HD Replaces OEM 705400756 703500823 705401943 705401115 705401384 705401947 705401704 Through years of research and development Demon Powersports has developed an axle that doesn’t burn a hole in your pocket and adheres to the highest quality standards. These axles are bigger, beefier, and stronger. Demon Heavy Duty Axles are built using larger CV joints and shafts, paired with our proprietary dual heat treatment process, and 4340 Chromoly Steel inner CV cage gives these the axles the edge it needs for superior strength and longevity. These axles also utilize a unique double plunge design which allows it to achieve higher articulation angles approximately, the axles are designed to slide on the bar splines allowing for 1.5 inches of travel and 40° articulation over terrain on the inboard joint. The outboard joint can travel 0.5inches and swing from 45°-47° depending on the model. The Demon heavy duty axles are equipped The TPEE (Thermoplastic polyester elastomer) boots which are stronger, stiffer, more fatigue resistant, puncture resistant, and more temperature resistant than a standard OEM boot. Axles use molybdenum grease to provide low friction and smooth motion. Trust in Demon Heavy Duty Axles to keep you riding!! • 15%-20% increase in diameter compared to regular axle • Inner cage made up of 4340 chromoly steel • Dual heat treated high strength chromoly steel shaft • Thermoplastic polyester elastomer (TPEE) Boot • 10%-15% increase in CV joint size compared to regular joints • Wider articulation angles • Dual plunge design prevents axle from binding • Packed with high load molybdenum grease Precision CNC machined • Can Fit 1.5”- 5” Bracket lift of particular brands/ All Portal Gear Lifts / 1.5”- 5” A-arms of particular brands • 1-year ltd warranty
All Balls Racing Fuel Pump Assembly Sending Unit Part number 47-1023 24-71023 1009-0138 Fits: 2006-2008 Outlander/Renegade 500 650 800HO Replaces OEM : 703500771
Aftermarket Fuel pump kit with pickup sock lines and seal Part number 1009-0090 Works with: 2016+ Defenders HD5 HD8 HD10 Outlander 450/570 and Renegade 570 Replaces the pump in sending units part numbers 709000461 and 709000662
New Demon Heavy Duty Axle Front Right (throttle side) Fits: G2 2012-2018 ATV Outlander/Renegade 500 570 650 800R 850 1000R Part number PAXL-3071HD Replaces OEM 705400757 703500824 705401944 705401116 Through years of research and development Demon Powersports has developed an axle that doesn’t burn a hole in your pocket and adheres to the highest quality standards. These axles are bigger, beefier, and stronger. Demon Heavy Duty Axles are built using larger CV joints and shafts, paired with our proprietary dual heat treatment process, and 4340 Chromoly Steel inner CV cage gives these the axles the edge it needs for superior strength and longevity. These axles also utilize a unique double plunge design which allows it to achieve higher articulation angles approximately, the axles are designed to slide on the bar splines allowing for 1.5 inches of travel and 40° articulation over terrain on the inboard joint. The outboard joint can travel 0.5inches and swing from 45°-47° depending on the model. The Demon heavy duty axles are equipped The TPEE (Thermoplastic polyester elastomer) boots which are stronger, stiffer, more fatigue resistant, puncture resistant, and more temperature resistant than a standard OEM boot. Axles use molybdenum grease to provide low friction and smooth motion. Trust in Demon Heavy Duty Axles to keep you riding!! • 15%-20% increase in diameter compared to regular axle • Inner cage made up of 4340 chromoly steel • Dual heat treated high strength chromoly steel shaft • Thermoplastic polyester elastomer (TPEE) Boot • 10%-15% increase in CV joint size compared to regular joints • Wider articulation angles • Dual plunge design prevents axle from binding • Packed with high load molybdenum grease Precision CNC machined • Can Fit 1.5”- 5” Bracket lift of particular brands/ All Portal Gear Lifts / 1.5”- 5” A-arms of particular brands • 1-year ltd warranty
New Demon Heavy Duty Axle Rear Right (throttle side) Fits: 2019+ ATV Outlander/Renegade 650 850 1000R Part number PAXL-3065HD Replaces OEM 705502711 705502713 705503024 Through years of research and development Demon Powersports has developed an axle that doesn’t burn a hole in your pocket and adheres to the highest quality standards. These axles are bigger, beefier, and stronger. Demon Heavy Duty Axles are built using larger CV joints and shafts, paired with our proprietary dual heat treatment process, and 4340 Chromoly Steel inner CV cage gives these the axles the edge it needs for superior strength and longevity. These axles also utilize a unique double plunge design which allows it to achieve higher articulation angles approximately, the axles are designed to slide on the bar splines allowing for 1.5 inches of travel and 40° articulation over terrain on the inboard joint. The outboard joint can travel 0.5inches and swing from 45°-47° depending on the model. The Demon heavy duty axles are equipped The TPEE (Thermoplastic polyester elastomer) boots which are stronger, stiffer, more fatigue resistant, puncture resistant, and more temperature resistant than a standard OEM boot. Axles use molybdenum grease to provide low friction and smooth motion. Trust in Demon Heavy Duty Axles to keep you riding!! • 15%-20% increase in diameter compared to regular axle • Inner cage made up of 4340 chromoly steel • Dual heat treated high strength chromoly steel shaft • Thermoplastic polyester elastomer (TPEE) Boot • 10%-15% increase in CV joint size compared to regular joints • Wider articulation angles • Dual plunge design prevents axle from binding • Packed with high load molybdenum grease Precision CNC machined • Can Fit 1.5”- 5” Bracket lift of particular brands/ All Portal Gear Lifts / 1.5”- 5” A-arms of particular brands • 1-year ltd warranty
New Demon Heavy Duty Axle Rear Left Fits: 2019+ ATV Outlander/Renegade 650 850 1000R Part number PAXL-3064HD Replaces OEM 705502710 705503025 705502712 Through years of research and development Demon Powersports has developed an axle that doesn’t burn a hole in your pocket and adheres to the highest quality standards. These axles are bigger, beefier, and stronger. Demon Heavy Duty Axles are built using larger CV joints and shafts, paired with our proprietary dual heat treatment process, and 4340 Chromoly Steel inner CV cage gives these the axles the edge it needs for superior strength and longevity. These axles also utilize a unique double plunge design which allows it to achieve higher articulation angles approximately, the axles are designed to slide on the bar splines allowing for 1.5 inches of travel and 40° articulation over terrain on the inboard joint. The outboard joint can travel 0.5inches and swing from 45°-47° depending on the model. The Demon heavy duty axles are equipped The TPEE (Thermoplastic polyester elastomer) boots which are stronger, stiffer, more fatigue resistant, puncture resistant, and more temperature resistant than a standard OEM boot. Axles use molybdenum grease to provide low friction and smooth motion. Trust in Demon Heavy Duty Axles to keep you riding!! • 15%-20% increase in diameter compared to regular axle • Inner cage made up of 4340 chromoly steel • Dual heat treated high strength chromoly steel shaft • Thermoplastic polyester elastomer (TPEE) Boot • 10%-15% increase in CV joint size compared to regular joints • Wider articulation angles • Dual plunge design prevents axle from binding • Packed with high load molybdenum grease Precision CNC machined • Can Fit 1.5”- 5” Bracket lift of particular brands/ All Portal Gear Lifts / 1.5”- 5” A-arms of particular brands • 1-year ltd warranty
New Demon Heavy Duty Axle Front Right (throttle side) Fits: 2019+ ATV Outlander/Renegade 650 850 1000R Part number PAXL-3063HD Replaces OEM 705402238 705402236 Through years of research and development Demon Powersports has developed an axle that doesn’t burn a hole in your pocket and adheres to the highest quality standards. These axles are bigger, beefier, and stronger. Demon Heavy Duty Axles are built using larger CV joints and shafts, paired with our proprietary dual heat treatment process, and 4340 Chromoly Steel inner CV cage gives these the axles the edge it needs for superior strength and longevity. These axles also utilize a unique double plunge design which allows it to achieve higher articulation angles approximately, the axles are designed to slide on the bar splines allowing for 1.5 inches of travel and 40° articulation over terrain on the inboard joint. The outboard joint can travel 0.5inches and swing from 45°-47° depending on the model. The Demon heavy duty axles are equipped The TPEE (Thermoplastic polyester elastomer) boots which are stronger, stiffer, more fatigue resistant, puncture resistant, and more temperature resistant than a standard OEM boot. Axles use molybdenum grease to provide low friction and smooth motion. Trust in Demon Heavy Duty Axles to keep you riding!! • 15%-20% increase in diameter compared to regular axle • Inner cage made up of 4340 chromoly steel • Dual heat treated high strength chromoly steel shaft • Thermoplastic polyester elastomer (TPEE) Boot • 10%-15% increase in CV joint size compared to regular joints • Wider articulation angles • Dual plunge design prevents axle from binding • Packed with high load molybdenum grease Precision CNC machined • Can Fit 1.5”- 5” Bracket lift of particular brands/ All Portal Gear Lifts / 1.5”- 5” A-arms of particular brands • 1-year ltd warranty
New Demon Heavy Duty Axle Rear Left Fits: 2006-2018 ATV Outlander/Renegade 500 570 650 800HO 800R 850 1000 1000R Part number PAXL-1130HD Replaces OEM 705500867 705500979 705501483 705502472 705501485 Through years of research and development Demon Powersports has developed an axle that doesn’t burn a hole in your pocket and adheres to the highest quality standards. These axles are bigger, beefier, and stronger. Demon Heavy Duty Axles are built using larger CV joints and shafts, paired with our proprietary dual heat treatment process, and 4340 Chromoly Steel inner CV cage gives these the axles the edge it needs for superior strength and longevity. These axles also utilize a unique double plunge design which allows it to achieve higher articulation angles approximately, the axles are designed to slide on the bar splines allowing for 1.5 inches of travel and 40° articulation over terrain on the inboard joint. The outboard joint can travel 0.5inches and swing from 45°-47° depending on the model. The Demon heavy duty axles are equipped The TPEE (Thermoplastic polyester elastomer) boots which are stronger, stiffer, more fatigue resistant, puncture resistant, and more temperature resistant than a standard OEM boot. Axles use molybdenum grease to provide low friction and smooth motion. Trust in Demon Heavy Duty Axles to keep you riding!! • 15%-20% increase in diameter compared to regular axle • Inner cage made up of 4340 chromoly steel • Dual heat treated high strength chromoly steel shaft • Thermoplastic polyester elastomer (TPEE) Boot • 10%-15% increase in CV joint size compared to regular joints • Wider articulation angles • Dual plunge design prevents axle from binding • Packed with high load molybdenum grease Precision CNC machined • Can Fit 1.5”- 5” Bracket lift of particular brands/ All Portal Gear Lifts / 1.5”- 5” A-arms of particular brands • 1-year ltd warranty
New Demon Heavy Duty Axle Rear Right (throttle side) Fits: 2006-2018 ATV Outlander/Renegade 500 570 650 800HO 800R 850 1000 1000R Part number PAXL-1129HD Replaces OEM 705500868 705500983 705501484 705502473 705501486 Through years of research and development Demon Powersports has developed an axle that doesn’t burn a hole in your pocket and adheres to the highest quality standards. These axles are bigger, beefier, and stronger. Demon Heavy Duty Axles are built using larger CV joints and shafts, paired with our proprietary dual heat treatment process, and 4340 Chromoly Steel inner CV cage gives these the axles the edge it needs for superior strength and longevity. These axles also utilize a unique double plunge design which allows it to achieve higher articulation angles approximately, the axles are designed to slide on the bar splines allowing for 1.5 inches of travel and 40° articulation over terrain on the inboard joint. The outboard joint can travel 0.5inches and swing from 45°-47° depending on the model. The Demon heavy duty axles are equipped The TPEE (Thermoplastic polyester elastomer) boots which are stronger, stiffer, more fatigue resistant, puncture resistant, and more temperature resistant than a standard OEM boot. Axles use molybdenum grease to provide low friction and smooth motion. Trust in Demon Heavy Duty Axles to keep you riding!! • 15%-20% increase in diameter compared to regular axle • Inner cage made up of 4340 chromoly steel • Dual heat treated high strength chromoly steel shaft • Thermoplastic polyester elastomer (TPEE) Boot • 10%-15% increase in CV joint size compared to regular joints • Wider articulation angles • Dual plunge design prevents axle from binding • Packed with high load molybdenum grease Precision CNC machined • Can Fit 1.5”- 5” Bracket lift of particular brands/ All Portal Gear Lifts / 1.5”- 5” A-arms of particular brands • 1-year ltd warranty
New Demon Heavy Duty Axle Front Left Fits: G1 ATV Outlander/Renegade 500 650 800HO 800R Part number PAXL-1128HD Replaces OEM 705400293 705400480 705400510 705400659 705400934 705401109 705401578 Through years of research and development Demon Powersports has developed an axle that doesn’t burn a hole in your pocket and adheres to the highest quality standards. These axles are bigger, beefier, and stronger. Demon Heavy Duty Axles are built using larger CV joints and shafts, paired with our proprietary dual heat treatment process, and 4340 Chromoly Steel inner CV cage gives these the axles the edge it needs for superior strength and longevity. These axles also utilize a unique double plunge design which allows it to achieve higher articulation angles approximately, the axles are designed to slide on the bar splines allowing for 1.5 inches of travel and 40° articulation over terrain on the inboard joint. The outboard joint can travel 0.5inches and swing from 45°-47° depending on the model. The Demon heavy duty axles are equipped The TPEE (Thermoplastic polyester elastomer) boots which are stronger, stiffer, more fatigue resistant, puncture resistant, and more temperature resistant than a standard OEM boot. Axles use molybdenum grease to provide low friction and smooth motion. Trust in Demon Heavy Duty Axles to keep you riding!! • 15%-20% increase in diameter compared to regular axle • Inner cage made up of 4340 chromoly steel • Dual heat treated high strength chromoly steel shaft • Thermoplastic polyester elastomer (TPEE) Boot • 10%-15% increase in CV joint size compared to regular joints • Wider articulation angles • Dual plunge design prevents axle from binding • Packed with high load molybdenum grease Precision CNC machined • Can Fit 1.5”- 5” Bracket lift of particular brands/ All Portal Gear Lifts / 1.5”- 5” A-arms of particular brands • 1-year ltd warranty
New Demon Heavy Duty Axle Front Right (throttle side) Fits: G1 ATV Outlander/Renegade 500 650 800HO 800R Part number PAXL-1127HD Replaces OEM 705400292 705400479 705400508 705400660 705400935 705401110 Through years of research and development Demon Powersports has developed an axle that doesn’t burn a hole in your pocket and adheres to the highest quality standards. These axles are bigger, beefier, and stronger. Demon Heavy Duty Axles are built using larger CV joints and shafts, paired with our proprietary dual heat treatment process, and 4340 Chromoly Steel inner CV cage gives these the axles the edge it needs for superior strength and longevity. These axles also utilize a unique double plunge design which allows it to achieve higher articulation angles approximately, the axles are designed to slide on the bar splines allowing for 1.5 inches of travel and 40° articulation over terrain on the inboard joint. The outboard joint can travel 0.5inches and swing from 45°-47° depending on the model. The Demon heavy duty axles are equipped The TPEE (Thermoplastic polyester elastomer) boots which are stronger, stiffer, more fatigue resistant, puncture resistant, and more temperature resistant than a standard OEM boot. Axles use molybdenum grease to provide low friction and smooth motion. Trust in Demon Heavy Duty Axles to keep you riding!! • 15%-20% increase in diameter compared to regular axle • Inner cage made up of 4340 chromoly steel • Dual heat treated high strength chromoly steel shaft • Thermoplastic polyester elastomer (TPEE) Boot • 10%-15% increase in CV joint size compared to regular joints • Wider articulation angles • Dual plunge design prevents axle from binding • Packed with high load molybdenum grease Precision CNC machined • Can Fit 1.5”- 5” Bracket lift of particular brands/ All Portal Gear Lifts / 1.5”- 5” A-arms of particular brands • 1-year ltd warranty
Have Questions?
Our staff is available to answer questions
canampartsguy@gmail.com
1340 Okray Ave.
Plover, WI 54467
jared@canampartsguy.com
Cant find What you're looking for?
Visit our 
store!
2016 Can Am Parts, LLC. All rights reserved.