Brand new aftermarket secondary clutch assembly This is found on many BRP ATVs. Please ask if you have fitment questions. Replaces OEM Part Part Numbers: 420280173 420280176 420280178 420932421 420280236 420280499 420245910 420245911 420220913 If your machine has a spring with pigtails you will need to use a spring without them as this aftermarket clutch does not have provisions for them. 420238176 OEM Black/Orange is a great substitute Installation Torque Specs: 45 ft·lb On the Secondary Bolt (red thread locker recommended, allow to set up overnight)- OUT OF STOCK
NEW OEM BRP Rotax Engine. 2016+ ATV 850 Vtwin 78 horsepower@ 7300 RPM, 94mm bore, 61.5mm stroke, 10.5:1 compression ratio. The 850 will have the larger valves when compared to the 800R, these were first seen in the 2013 1000R maverick engine, these are 36.5mm and 31mm respectively. This is new, not rebuilt. It will ship as pictured. No electronics included, you will need to transfer over your parts. Shipped with signature required. 
CVtech Slider Shoe HD set of three for stamped plate 0930-3002
NEW Spanner Wrench This is to remove and install the 705501550 nut on ATVs with the tapered roller bearing rear differentials. Also known as the XMR or 2019+ style rear diffs. Use a 20 spline yoke to retain the assembly in a vice and spin the nut off. The nut should be RH threaded
New aftermarket 91mm bore piston and cylinder kit with gaskets rings wrist pins and circlips 10.5:1 compression ratio This is a ready to bolt on kit Fits: Commander 1000 ATV 1000/1000R Defender HD10 and DH9 Maverick Sport 1000 Please note this kit will not fit the SXS 1000R due to the lower compression ratio. No dowel pins included, you will need to transfer these from your engine Replaces OEM Part Numbers: 420685242 420685248 420623568 420623566 420630210 420245436 420216351 420685244 420296774
Set of four Moose gas shock kit for G1 Outlander 650/800 or Renegade 500/800 These shocks are the same length on all four corners, you may notice a slight lift, more so on a well used machine. *Please note these will not work in place of struts found on the Outlander 400/500 machines. Features: Moose gas shocks offer long term consistent performance over stock oil only damped shocks 10% stiffer springs provide a better ride and higher load capacity Works great on the front to better support your snowplow and on the rear when hauling cargo Smooth black color blends perfectly on your machine Direct bolt-on replacement: pre-installed spring allows for quicker setup P/N13102146X4
Kit includes one universal boot, one reusable cone tool, two stainless steel clamps, grease pack, and silicone cone lube and instructions Expandable universal CV boot, slides and expands over reusable cone tool for trail side CV boot replacement Lithium based molybdenum grease ensures good lubrication for long CV joint life XL version of the original EZ Trail boot designed to fit UTVs and large ATVs Material is expandable yet tough enough to be a permanent fix Two clamping diameters ensure a good fit on most vehicles Boot material stays flexible in extreme cold temperatures
Slider Blocks for Trailbloc Primary clutches for CANAM ATVS This is a set of six, you will need to transfer over your weights. Part number 0930-3022
New Genuine OEM steering stem for G2 Outlander and Renegade This will only fit NON power steering models Will not work on power steering bikes Current Part number 709401008
New Can Am Outlander Renegade and Commander V-Twin EFI Speedo Speedometer Display Dash 2018-2020 Please understand 2017 and older models require a different dash, even if yours looks the same. This is the factory Gauge/Screen. The dash is designed to auto pair, but sometimes it will not auto pair and you will have to program them together with buds software. This can be done at your local dealer or you can send in your ecu, key(s), and DPS (power steering) to us for programming. Contact for more information. It will display 0 miles, please record your current miles for your records. Current Part number: 710005553
NEW OEM BRP Thermostat Current part number 709200406 replaces 709200383 This style is external from the cylinder head. If you are unsure on fitment please contact us.
NEW Outsiders Mud Crew Airbox seal This is an improved design over factory Apply a small amount of grease to aid install, this is much thicker and denser than the OEM o-ring or gasket Replaces OEM part numbers: 293300165 293300175 293300179
All Balls complete fuel pump module, retaining nut and gasket This fits G1 Models: 2009-2015 EFI Outlander 400 2009-2012 Outlander or Renegade 500 2009-2012 Outlander 650 2009-2011 Outlander 800R 2012 Outlander 800R XMR 2012 Outlander 800R MAX 2009-2011 Renegade 800R Part number: 47-1049 24-71022 Replaces OEM numbers: 703500766 703500781 709000194 709000245- OUT OF STOCK
NEW OEM Brake Line Fits 2012-17 Renegade 500 570 800R 1000 and 1000R Current part number 705601489 Replaces 705601123 705601060 This connects the front master cylinder to the front calipers. Brake lines on 2012+ and newer Can-am ATVs are known to be difficult to bleed, it is best to set some time aside to bleed it multiple times to get a firm lever. 
Part number 0950-1011
This isolates the spring from the one way bearing on a trail bloc primary clutch.
Measurements as shown
Can-am Rear Driveshaft G2 2019+ G2 Renegade 1000R base, XXC or XMR All New All OEM Shaft OEM U-joints, with OEM gearbox seal protector installed. **Please note, this is the most updated shaft and does not require a wear ring on the differential side of the shaft. The last two pictures illustrate this.** 20 Spline Gearbox side yoke (fits large type gearboxes) 20 Spline Differential side yoke (fits fits 705502808/705502546 rear differential) Current Part number: 703500990 Previous Part number: 703500928 703500901
Updated Can-am Rear G2 Driveshaft Fits: 2019+ Outlander 1000R (excluding MAX and XMR) 2019+ Outlander 650/850 (excluding MAX) 2019+ Renegade 650/850 All new all OEM Shaft OEM U-joints. OEM protector ring installed Gearbox side yoke swapped to 18 spline Current Part number: 703500988 Previous Part number: 703500858 703500931 If you have a 2019+ 570 short wheel base single rider, this may be the correct shaft for your application, the parts fiche may not show the correct part number. You will need to measure the outer diameter of your rear differential's pinon seal, this shaft will only work with machines that have a 80mm pinion seal. If you measure 70mm you will need 703500986. 20 spline differential side yoke (fits 705502808/705502546 rear differential) 18 spline gearbox side yoke (small gearbox size) No wear ring needed, the deferential side yoke is machined to the outer diameter that a wear ring would be.
SHIPS FREE TO THE LOWER 48 STATES OEM BRP Heated Grips and Thumb kit.- LED dimmer facilitates reading temperature settings. 4 temperature settings with individual controls for thumb and grips. Returns to previous heat setting. One-touch shutdown. Compatible with Intelligent Throttle Control (ITC). Wiring Cable (710004567) is required for installation on G2 650 and G2L 570.
- OUT OF STOCK
All Balls complete module, retaining nut and gasket This fits many G2 model ATVs please contact us if you have fitment questions. Part number: 1009-0139 47-1024 Replaces OEM numbers: 709000287 709000758 
Brand New Moose Utility 13 Bolt CVT Cover Gasket
Works on 7 bolt covers also.
Part number 0935-1193
replaces: 420430127 420430126 420430124 420430123 420430120
Rugged wheels spacers are made from T6061 aluminum alloy and are precisely CNC machined for accurate dimensions. Spacers can be direct bolt on and can use OEM studs. If you are looking to widen the stance of your machine, clear larger tires or get some new wheels. These spacers are just what you need. These spacers are sold as a pair. One inch thick The bolt pattern is 4x137mm M10 studs Part number PAWS-1035
Rugged wheels spacers are made from T6061 aluminum alloy and are precisely CNC machined for accurate dimensions. Spacers can be direct bolt on and can use OEM studs. If you are looking to widen the stance of your machine, clear larger tires or get some new wheels. These spacers are just what you need. These spacers are sold as a pair. 1.5 inch thick The bolt pattern is 4x137mm M10 studs Part number PAWS-1036
Rugged wheels spacers are made from T6061 aluminum alloy and are precisely CNC machined for accurate dimensions. Spacers can be direct bolt on and can use OEM studs. If you are looking to widen the stance of your machine, clear larger tires or get some new wheels. These spacers are just what you need. These spacers are sold as a pair. Two inch thick The bolt pattern is 4x137mm M10 studs Part number PAWS-1037
NEW OEM BRP Coupler This is found on many machines, 18 spline exterior No need for a wear ring on this coupler. Part number 705401969 Replaces 703500678 705400149 705500201
Have Questions?
Our staff is available to answer questions
canampartsguy@gmail.com
1340 Okray Ave.
Plover, WI 54467
jared@canampartsguy.com
Cant find What you're looking for?
Visit our 
store!
2016 Can Am Parts, LLC. All rights reserved.