SHIPS FREE TO THE LOWER 48 STATES Late G1 Early G2 Standard Rear Differential Bearing and Seal Kit High quality aftermarket bearings along with double lip axle seals. Bearing and Seal Brands include: Nachi, KOYO, NTN, Timken The large case sealing and pinion gear O-rings are NOT included as a cost saving measure, these O-rings are reusable if not damaged. There are a few options for kits, please verify your differential uses this style of gears before ordering! This will only fit six mounting hole differentials. Open up the differential! Check for two bearings total (one on each side) on the ring gear. If you only have two proceed to the next measurement. Measure your outer diameter of your axle seals! They should measure close to 1 3/4" (47mm) To further verify fitment you can measure your pinion pilot shaft, this should be 9/16″ (14mm) The last pictures show this very clearly. Please take the time to measure your parts before buying this will save time and restocking fees.
SHIPS FREE TO THE LOWER 48 STATES
Late G1 Early G2 Standard Rear Differential Rebuild Kit
There are a few options for rebuild kits, please measure your parts before ordering!!
OEM Rear Differential Gear set 10/36 Ring and Pinion gear set. The gears are straight cut as pictured.
Paired with high quality aftermarket bearings along with double lip axle seals.
This kit should be installed by an experienced technician. Ring gear shims are included as the gears will need to be set up in your cases, the pinion shims should remain unchanged
Note: the O rings are not included, this is a cost savings measure as they are generally reusable.
There are a few options for kits, please verify your differential uses this style of gears before ordering! This will only fit six mounting hole differentials.
Open up the differential! Check for two bearings total (one on each side) on the ring gear. If you only have two proceed to the next measurement.
Measure your outer diameter of your axle seals!
They should measure close to 1 3/4" (47mm)
To further verify fitment you can measure your pinion pilot shaft, this should be 9/16? (14mm)
The last pictures show this very clearly. Please take the time to measure your parts before buying this will save time and restocking fees.
Brand New Moose Utility 13 Bolt CVT Cover Gasket
Works on 7 bolt covers also.
Part number 0935-1193
replaces: 420430127 420430126 420430124 420430123 420430120
New Moose fuel pressure regulator for Canam Vtwins. Part number 1009-0114
Set of four Moose gas shock kit for G1 Outlander 650/800 or Renegade 500/800 These shocks are the same length on all four corners, you may notice a slight lift, more so on a well used machine. *Please note these will not work in place of struts found on the Outlander 400/500 machines. Features: Moose gas shocks offer long term consistent performance over stock oil only damped shocks 10% stiffer springs provide a better ride and higher load capacity Works great on the front to better support your snowplow and on the rear when hauling cargo Smooth black color blends perfectly on your machine Direct bolt-on replacement: pre-installed spring allows for quicker setup P/N13102146X4- OUT OF STOCK
SHIPS FREE TO THE LOWER 48 STATES 0934-3019 Moose Racing Gasket Kit Fits Outlander/Renegade 800 models. Complete kit with oil seals. Center case gasket Magneto Cover Gasket PTO Cover Gasket Two Cylinder base Gaskets Two Cylinder Head Gaskets Two Valve Cover Gaskets Water Pump Cover Seal (kit does not come with mechanical seal) 
Impact-absorbing rubber prevents bottoming-out of winch Prevents hook rattling when not in use A must-have for preventing damage to your winch fairlead Made in the U.S.A. 2 1/2″ Diameter 1 3/4″ Thick Part number 4505-0475
For use with all BRP turn key type ignition switches. Will not fit RFID type ignitions. Simply cut off the old harness and use the included butt connectors or solder the connections to the new pigtail. Be sure to match up one wire at a time when installing, this helps avoid switching wire orientation as the wires are not color coded. The wires are 6” long so it can be fixed inside the headlight pod Sold each; includes butt connectors and zip ties Part number 2120-0943
neapco Brand U joint for front drive shafts These U joints are made in Italy, please do not confuse these with the sub-grade china made u joints. Fits: G1 Renegade and Outlander . Also works on Outlander 400 Rear shafts. Maverick/Commander front driveshafts Will not fit: Maverick X3/Sport/Trail or Defender Includes clips, and grease fitting. Pro tip: Install grease fitting before pressing in u joint. Install u joint in a manner where you can still grease the joint in chassis. Replaces OEM : 715900325 703000023 703000024 703500002 703500135 703500607 703500814
Replaces OEM 703500836 Japan Made Uncaged Needle Bearing 20X27X15mm Needle Bearing for XMR rear differential pinion gear
New NGK Spark Plug 93444
OEM part number 715900352
NGK part number LMAR8D-J
These spark plugs work in 2015+ Outlander/Renegade 450 850 and 1000R also fits Defender HD5
Shell
Thread Diameter: 10mm
Thread Pitch: 1.0mm
Seat Type: Gasket
Reach: 26.5mm (1.04″)
Hex Size: 9/16″ (14mm)
Terminal Type: Solid
Gap: .031″ (0.8mm)Center Electrode
Material: Nickel
Type: Standard
Size: 2.5mm
Projection: ProjectedGround Electrode
Material: Nickel
Type: Multi-GroundSpecifications
Resistor: Yes
Resistor Value: 5k Ohm
Heat Range: 8
Torque Specs: Aluminum: 7.2-8.7 lb. ft.
Connecting Rod Bolt for 1000 V twin Engines This is the OEM bolt with a size of M9x1x45 Part number 420641477 420641475
Have Questions?
Our staff is available to answer questions
canampartsguy@gmail.com
1340 Okray Ave.
Plover, WI 54467
jared@canampartsguy.com
Cant find What you're looking for?
Visit our 
store!
2016 Can Am Parts, LLC. All rights reserved.