- OUT OF STOCK
SHIPS FREE TO THE LOWER 48 STATES New Forged OEM Can-am piston kit with rings. Matched to an OEM Rotax used Cylinder. This is ready to install on your 650 Outlander engine. Two are required per engine. Piston comes with rings installed. Piston pin, and clips are not included. Part number 420684111 420613888 
All Balls complete fuel pump module, retaining nut and gasket This fits G1 Models: 2009-2015 EFI Outlander 400 2009-2012 Outlander or Renegade 500 2009-2012 Outlander 650 2009-2011 Outlander 800R 2012 Outlander 800R XMR 2012 Outlander 800R MAX 2009-2011 Renegade 800R Part number: 47-1049 24-71022 Replaces OEM numbers: 703500766 703500781 709000194 709000245
Brand new inner secondary clutch This inner clutch has the hole for the pig tale style spring but will work on springs without the pig tale. New OEM Part Part Numbers : 420280499 420280235 420248233 420280236 420280238 420280497
SHIPS FREE TO THE LOWER 48 STATES OEM BRP Heated Grips and Thumb kit.- LED dimmer facilitates reading temperature settings. 4 temperature settings with individual controls for thumb and grips. Returns to previous heat setting. One-touch shutdown. Compatible with Intelligent Throttle Control (ITC). Wiring Cable (710004567) is required for installation on G2 650 and G2L 570.
NEW Take Off G2 Outlander Renegade Left Swing Arm 706001860 Removed From Machine With 9.5 Miles.
New Genuine OEM Made of aluminum Large ports for clearing of snow and mud Aggressive design for improved traction Will not work with body side protectors Sold in pairs All hardware is included Click here for instructions
SHIPS FREE TO THE LOWER 48 STATES Updated Can-am Rear G2 Outlander/Renegade 2019 and newer prop shaft. All new all OEM Shaft OEM U-joints. OEM protector ring installed Input yoke swapped to 18 spline This is the correct length for short wheel base single seat 500/570/650/800/850 Outlander or Renegade with 1000 XMR rear differential. This will also work on 2015+ Outlander short wheel base, single seat 1000/1000R with 1000 XMR rear differential. Direct replacement for 2015 and newer 800/850 XMR Current Part number: 703500988 Previous Part number: 703500858 703500931 20 spline differential side yoke 18 spline gearbox side yoke No wear ring needed- Updated Can-am Rear G2 Driveshaft Fits: 2019+ Outlander 1000R (excluding MAX and XMR) 2019+ Outlander 650/850 (excluding MAX) 2019+ Renegade 650/850 All new all OEM Shaft OEM U-joints. OEM protector ring installed Gearbox side yoke swapped to 18 spline Current Part number: 703500988 Previous Part number: 703500858 703500931 If you have a 2019+ 570 short wheel base single rider, this may be the correct shaft for your application, the parts fiche may not show the correct part number. You will need to measure the outer diameter of your rear differential's pinon seal, this shaft will only work with machines that have a 80mm pinion seal. If you measure 70mm you will need 703500986. 20 spline differential side yoke (fits 705502808/705502546 rear differential) 18 spline gearbox side yoke (small gearbox size) No wear ring needed, the deferential side yoke is machined to the outer diameter that a wear ring would be.
NEW Genuine Can-am Rear Prop Shaft for 2012-18 Outlander Or Renegade 500, 570L, 570, 650, 800R or 850.
Be sure to check part numbers before ordering if you have a 1000.
This will work on 2015+ Outlander 1000 non XMR/T3 machines (small gearbox).This updated shaft does not need wear ring as it is simply machined larger in outer diameter.
Current Part number: 703500986
Previous Part numbers: 703500925 703500855 70550140618 spline gearbox side yoke
18 spline differential side yoke
New G2 dual piston Left Right Brake caliper with OEM pads.
Fits G2 Renegade and Outlander 2012-current
Genuine OEM part. Part number 705600860
NEW Take Off G2 Can Am Outlander 570 Fuel Pump Assembly Part Number 709000461 From Machine With 9.5 Miles.
SHIPS FREE TO THE LOWER 48 STATES New OEM Standard G2 Rear Differential Ring & Pinion Gear Set 1652 There are a few options for kits, please verify your differential uses this style of gears before ordering! This will only fit six mounting hole differentials. OEM Rear Differential Gear set 10/36 Ring and Pinion gear set. The gears are straight cut as pictured. Open up the differential! Check for two bearings total (one on each side) on the ring gear. If you only have two proceed to the next measurement. Measure your outer diameter of your axle seals! They should measure close to 2 1/16? (52mm) To further verify fitment you can measure your pinion pilot shaft, this should be 5/8? (16mm) Please take the time to measure your parts before buying this will save time and restocking fees. Fits 2015 -2019 G2 style ATV 500/570/650/800/850/1000/1000R NON-XMR style REAR differential. 570/650 XMR machines do not have the true XMR differential.
Have Questions?
Our staff is available to answer questions
canampartsguy@gmail.com
1340 Okray Ave.
Plover, WI 54467
jared@canampartsguy.com
Cant find What you're looking for?
Visit our 
store!
2016 Can Am Parts, LLC. All rights reserved.