NEW Spanner Wrench This is to remove and install the 705501550 nut on ATVs with the tapered roller bearing rear differentials. Also known as the XMR or 2019+ style rear diffs. Use a 20 spline yoke to retain the assembly in a vice and spin the nut off. The nut should be RH threaded
Can-Am 703500865 Secondary Clutch Driven Pulley Stud Nut Screw Kit Secondary Stud/Nut Kit M10x136mm You will need to reuse your washer. This kit will work on every Vtwin ATV factory driven (secondary) clutch (pulley) Also fits Commander driven clutch Will work on non QRS Maverick driven clutch If you have fitment questions, please contact us, we are here to help. Part numbers: 703500865 420441900 420242097 420242402
Genuine OEM Start/Stop Switch
This has the additional single light blue wire with connector.
Current Part Number: 710006134
Fits some 2019 Outlander and Renegade 1000R, 2020 Outlander and Renegade 850/1000R
Please contact us if you are not 100% sure on fitment, we will be happy to assist
New OEM Canam CVT Air Intake pre-filter Fits 2013+ Outlander G2 with the round CVT intake duct inlet. Part # 715003483 Adds extra protection to your engine in harsh riding conditions. Filter blocks particles larger than 0.007" (0.19 mm). Easy, tool-less installation. Necessary to maintain vehicle warranty when tracks are installed. Standard on Outlander 650 X mr, 850, 1000, 1000R engines & G2L PRO. Not compatible with Snorkel kits
Allows the installation of accessories with 16” base on LinQ racks. Tool-less installation and removal. Part number 715004960
OEM Snorkel kit, this raises the engine air intake well above the handlebars. The ECU is relocated to allow for CVT breather tubes to extend upward. This kit includes the brackets for the two plug type ECU found on ride by wire outlanders. With the tubes molded specifically for this application this is the cleanest kit you can install on your machine. Part number 715005999 Installation time is approximately 3.5 hours This snorkel kit is not compatible with the XT Handlebar Protector Kit (P/N 715000271) 715005999 instructions
SHIPS FREE TO THE LOWER 48 STATES New OEM XMR Rear Differential Gear set, 10/36 Ring and Pinion gear set, Timken, Dichtomatik or SKF seals, NTN or IKO pilot bearing , OEM shim kit and OEM bearings Fits the larger style 800/850/1000/1000R XMR style REAR differential first seen on the 2013 Outlander 1000 XMR. This gear set will not install into 650 xmr and 570 xmr differential cases. Please see our other listings for those. This is a common part to swap on to generation 2 atvs. We do sell complete kits to do so, please check out our other listings. Part number 703500870
Vertex-Winderosa 810985 Top End Gasket Kit Fits 2016+ Outlander and Renegade 570
Top End Gasket Kit, 93mm Bore, .018″ MLS Cylinder Head Gasket
Big bore GASKET KIT for 650/800 based engines.
MLS (Muti Layer Steel) Cometic head gaskets and steel base gaskets, OEM paper base gaskets are recommended as the steel base gaskets require the surface to be perfect.
High quality aftermarket Timken or SKF axle oil seal. Fits ATV rear differentials 2015-current, some UTV’s To be 100% sure on fitment, measure your outer diameter on your seal, it should read 52mm This seal has a 30mm inner diameter 52mm outer diamter and is 8mm thick. Replaces OEM 705501556 Order qty two per machine.
New G2 dual piston front right brake caliper with pads. Fits G2 Renegade and Outlander 2012+ Replaces Part number 705600861
NEW AFTERMARKET OIL COOLER VTWIN Fit on the "big block" cases Will come as pictured Part Numbers: 420890180
Have Questions?
Our staff is available to answer questions
canampartsguy@gmail.com
1340 Okray Ave.
Plover, WI 54467
jared@canampartsguy.com
Cant find What you're looking for?
Visit our 
store!
2016 Can Am Parts, LLC. All rights reserved.