Outlander

  • New Moose fuel pressure regulator for Canam Vtwins. Part number 1009-0114
  • Set of four Moose gas shock kit for G1 Outlander 650/800 or Renegade 500/800 These shocks are the same length on all four corners, you may notice a slight lift, more so on a well used machine. *Please note these will not work in place of struts found on the Outlander 400/500 machines. Features: Moose gas shocks offer long term consistent performance over stock oil only damped shocks 10% stiffer springs provide a better ride and higher load capacity Works great on the front to better support your snowplow and on the rear when hauling cargo Smooth black color blends perfectly on your machine Direct bolt-on replacement: pre-installed spring allows for quicker setup P/N13102146X4
  • OUT OF STOCK
    SHIPS FREE TO THE LOWER 48 STATES 0934-3019 Moose Racing Gasket Kit Fits Outlander/Renegade 800 models. Complete kit with oil seals. Center case gasket Magneto Cover Gasket PTO Cover Gasket Two Cylinder base Gaskets Two Cylinder Head Gaskets Two Valve Cover Gaskets Water Pump Cover Seal (kit does not come with mechanical seal)
  • Moose Utility Division handlebars Replaces factory OEM handlebars 7/8? diameter standard size made from .083 steel tubing Pullback/Sweep: 4? Width: 32? Center Width: 5-1/2? Does not come with hand grips May fit other years or models Made in the U.S.A. Will come as pictured Replaces OEM Part Numbers: 709401240 709400877 709400292 Parts unlimited number: 0601-4379
  • SHIPS FREE TO THE LOWER 48 STATES Complete Engine Gasket Kit With Oil Seals Fits 500 and 650 Outlanders and 500 Renegades We have used these in many engines with great success. Part number 0934-3018 Replaces OEM 420684145, 420684141
  • Impact-absorbing rubber prevents bottoming-out of winch Prevents hook rattling when not in use A must-have for preventing damage to your winch fairlead Made in the U.S.A. 2 1/2″ Diameter 1 3/4″ Thick Part number 4505-0475
  • For use with all BRP turn key type ignition switches. Will not fit RFID type ignitions. Simply cut off the old harness and use the included butt connectors or solder the connections to the new pigtail. Be sure to match up one wire at a time when installing, this helps avoid switching wire orientation as the wires are not color coded. The wires are 6” long so it can be fixed inside the headlight pod Sold each; includes butt connectors and zip ties Part number 2120-0943
  • neapco Brand U joint for front drive shafts These U joints are made in Italy, please do not confuse these with the sub-grade china made u joints. Fits: G1 Renegade and Outlander . Also works on Outlander 400 Rear shafts. Maverick/Commander front driveshafts Will not fit: Maverick X3/Sport/Trail or Defender Includes clips, and grease fitting. Pro tip: Install grease fitting before pressing in u joint. Install u joint in a manner where you can still grease the joint in chassis. Replaces OEM : 715900325 703000023 703000024 703500002 703500135 703500607 703500814
  • Replaces OEM 703500836 Japan Made Uncaged Needle Bearing 20X27X15mm Needle Bearing for XMR rear differential pinion gear
  • NEW NGK Spark Plug Part number 715900785 replaces 420897096 NGK number LMAR8AI-8 HD7/HD5 500/700
  • New NGK Spark Plug 93444

    OEM part number 715900352

    NGK part number LMAR8D-J

    These spark plugs work in 2015+ Outlander/Renegade 450 850 and 1000R also fits Defender HD5

    Shell

    Thread Diameter: 10mm
    Thread Pitch: 1.0mm
    Seat Type: Gasket
    Reach: 26.5mm (1.04″)
    Hex Size: 9/16″ (14mm)
    Terminal Type: Solid
    Gap: .031″ (0.8mm)

    Center Electrode

    Material: Nickel
    Type: Standard
    Size: 2.5mm
    Projection: Projected

    Ground Electrode

    Material: Nickel
    Type: Multi-Ground

    Specifications

    Resistor: Yes
    Resistor Value: 5k Ohm
    Heat Range: 8
    Torque Specs: Aluminum: 7.2-8.7 lb. ft.

     

     

  • Connecting Rod Bolt for 1000 V twin Engines This is the OEM bolt with a size of M9x1x45 Part number 420641477 420641475

Title