NEW Take Off G2 Can Am Outlander Front Diff Assembly 703500900 Unit-51. Part number 703500900 Pulled From Machine With 9.5 Miles. This fits 2006 and newer machines. Please note this is the visco lok style differential non electronic, for use with machine equipped with DPS, as this locks up quicker than the non DPS style. If you have fitment questions please contact us!
New IKO, Koyo or NTN brand needle bearing B98 replaces 705500261 If you are unsure on fitment please reach out to us we will help.
NEW OEM Center Rear Differential for Outlander 6x6 models. Part number 705503088 replaces 705502230 705501917- OUT OF STOCK
Aftermarket Four wheel drive servo motor. This is what engages the sliding collar putting power to the front differential. Part number 715900614 420891087 415129174 - OUT OF STOCK
Brand New Genuine OEM front differential This is the visco 4lok model which has the electronic locking mechanism Part number 705403049 replaces 705402700 This is found in the 2021+ G2 XMR, XTP and XXC models. You will need to transfer over your fill plug after filling this with gear oil. 
Differential Vent Tube 8mm diameter Part number 705501584
New OEM Can Am Outlander, Renegade 1000R XXC Gearbox
Current Part Number- 420686568
Previous Part Numbers- 420686565 NEW OEM Canam PartNOT A REBUILD, ALL NEW Brand New In The Box
Fits- Maverick 1000R, Commander 1000 or 800, Outlander 1000 2012-2014, all Outlander XMR 1000/1000R, Renegade 1000/1000R.
If unsure of fitment, please contact us. We will be happy to help!These ratios are published in the 2019 Service manual, we have not confirmed these to be accurate.
Ring and Pinon Gears 37/15=2.467
Intermediate 45/40=1.125
High Range 36/27=1.333
Low Range 46/17=2.706
Reverse 34/12=2.833Overall Gear Ratios:
High Range 3.700
Low Range 7.510
Reverse Range 7.863
Gearbox Shift Shaft Seal 28mm OD 12mm ID 7mm Thick Part numbers: 711250450 420250450
1447 NEW OEM Needle bearing 14x20.65x19 Size These are KOYO Bearings high quality 14mm Inner Diameter 20.65mm Outer Diameter 19mm Long Replaces OEM Part number 705501408
NEW Spanner Wrench This is to remove and install the 705501550 nut on ATVs with the tapered roller bearing rear differentials. Also known as the XMR or 2019+ style rear diffs. Use a 20 spline yoke to retain the assembly in a vice and spin the nut off. The nut should be RH threaded
New Oem Canam Pinion nut, this is spun on to the pinion gear to retain the bearings on the pinion gear of xmr differentials on ATV XMR's G2 800/850/1000/1000R This is not needed on 570 or 650 XMR models The threads are M28x1.25 Right Hand the outer diameter is 51mm Please check that this is the correct nut for your application Part number 705501550
SHIPS FREE TO THE LOWER 48 STATES NEW OEM Canam Parts OEM 14% LOWER LOW GEAR SET for most every 1000 Vtwins minus north american 2015 and newer outlander 1000/1000R This is the way to reduce the over all Low Gear ratio on your can-am 1000 running larger tires. This is the LOW RATIO for any Large Gearbox. The last picture shows a Large gearbox. This will not fit Small Gearboxes. 14% lower gear ratio than standard 1000 gear boxes (Maverick, Commander, Renegade, Outlander) Will also fit 800 Commander
New Can Am ATV Low Ratio Small Gear Box / Transmission Will work on all Can-am Vtwin 500/570/650/800/850 Both Outlander or Renegade.- New Can-Am GEAR BOX
- Current Part Number- 420686612
- Replaces: 420684820, 420684824, 420684825, 420684827
- NEW OEM Canam Part NOT A REBUILD, ALL NEW
- This is the Low Ratio (6.4% Lower HIGH Range) gearbox than a standard 800 gearbox.
- This is found in Outlander or Renegade 500's, Outlander 650's and the Outlander 800R XMR
NEW Speed Sensor Quad Logic brand Will fit 2006-Current Outlander, Renegade, Maverick, Maverick X3, Commander, and Defenders 2210-0568 500-1024 Replaces OE Numbers 420265621, 420265622, 420265624, 420265625, 420265626, 420265629, 707000745 and 711265622
New Can Am ATV 800 Standard Ratio Small Gear Box / Transmission Will work on all Can-am Vtwin 500/570/650/800/850 Both Outlander or Renegade.- New Can-Am GEAR BOX
- Current Part Number- 420686714
- Replaces: 420684780, 420685391, 420685392, 420685394, 420685396, 420685397
- NEW OEM Canam Part NOT A REBUILD, ALL NEW
- This is the Standard Ratio gearbox for any 500/570/650/800/850 v twin Can-am, Renegade or Outlander.
OEM oring commonly used on distance ring on gearbox input shaft. 420631610 replaces 420631615
There are a few options for kits, please verify your differential uses this style of gears before ordering!
This will only fit six mounting hole differentials.
Late G1 Early G2 Standard Rear Differential Ring 36t and Pinion 10t gear set Pinion bolt size is M10, this may be different than what you are replacing.
OEM Rear Differential Gear set 10/36 Ring and Pinion gear set. The gears are straight cut as pictured. This kit should be installed by an experienced technician.
Open up the differential! Check for two bearings total (one on each side) on the ring gear. If you only have two proceed to the next measurement. Measure your outer diameter of your axle seals! They should measure close to 1 3/4? (47mm) To further verify fitment you can measure your pinion pilot shaft, this should be 9/16" (14mm) The pictures show this very clearly. Please take the time to measure your parts before buying this will save time and restocking fees.
This is the 2019+ rear differential found in Renegades and Outlanders 650 and larger This has the 6 inch (155mm) ring gear with straight cut teeth as shown. It will fit g2 bikes (500/650/800/1000) if you are upgrading you will need to shorten your shaft 1.75 inches or buy a kit from us, please see our other listings. (G1 bikes will require further modifications to work). This has a provision for an abs sensor, but will fit bikes without a rear diff sensor BRP claims 25% increase in load capacity on this gear set vs the spiral cut xmr final drive units (rear differentials) from 13-18 models. Pinion spline count 20 Current part number 705502808
SHIPS FREE TO THE LOWER 48 STATES New OEM Standard G2 Rear Differential Ring & Pinion Gear Set 1652 There are a few options for kits, please verify your differential uses this style of gears before ordering! This will only fit six mounting hole differentials. OEM Rear Differential Gear set 10/36 Ring and Pinion gear set. The gears are straight cut as pictured. Open up the differential! Check for two bearings total (one on each side) on the ring gear. If you only have two proceed to the next measurement. Measure your outer diameter of your axle seals! They should measure close to 2 1/16? (52mm) To further verify fitment you can measure your pinion pilot shaft, this should be 5/8? (16mm) Please take the time to measure your parts before buying this will save time and restocking fees. Fits 2015 -2019 G2 style ATV 500/570/650/800/850/1000/1000R NON-XMR style REAR differential. 570/650 XMR machines do not have the true XMR differential.
XPS SAE 75W-90 Synthetic Gear Oil Kit. Enough to do a complete service on the front differential, rear differential, and gear box. 1 U.S QT 946ml per bottle This listing is for 2 quarts See your owners manual before ordering to make sure you order the correct weight for your Can Am 779158
NEW OEM GEARBOX 570s come with a lower ratio gearbox than the normal low ratio gearboxes found in the 650’s and 500’s The extra low ratio gearbox will help bottom end power and with larger tires, this is the lowest ratio small gearbox. Current Part Number 420686569 Replaces: 420686567 420686560 420686561 This is found in Outlander or Renegade 570 DPS XT or XMR Will work in 650,800,850, and 2015 and newer 1000/1000R ATV’s Teeth count and gear ratio Ring & Pinion 38/28 = 1.357 High Gear set 46/20 = 2.300 Low Gear set 31/14 = 2.214 High final ratio 3.341:1 Low final ratio 5.662:1 2015 and newer non XMR outlander 1000’s have this style gearbox, if you have fitment questions, please contact us! If you are installing this on an early G1 ATV you will need to transfer over your gear position sensors.
1652 NEW OEM Needle bearing 16x22x19 Size These are OEM Canam Bearings high quality brands like NTN are used. 16mm Inner Diameter 22mm Outer Diameter 19mm Long Part number 705502058
Moose Racing gearbox bearing and seal kit. Part number 1104-0021 This is for small gearboxes found in Outlander and Renegade 500, 570, 650, 800, 850 and some 2015 and newer Outlander 1000’s ATV’s If you have fitment questions, please ask, we are here to help.
Can-am Shim Kit for XMR G2 800 or larger 2012-current Rear Differentials. Part number 703500835
Have Questions?
Our staff is available to answer questions
canampartsguy@gmail.com
1340 Okray Ave.
Plover, WI 54467
jared@canampartsguy.com
Cant find What you're looking for?
Visit our 
store!
2016 Can Am Parts, LLC. All rights reserved.