- New Can-Am GEAR BOX
- Current Part Number- 420686714
- Replaces: 420684780, 420685391, 420685392, 420685394, 420685396, 420685397
- NEW OEM Canam Part NOT A REBUILD, ALL NEW
- This is the Standard Ratio gearbox for any 500/570/650/800/850 v twin Can-am, Renegade or Outlander.
New Can Am ATV 800 Standard Ratio Small Gear Box / Transmission Will work on all Can-am Vtwin 500/570/650/800/850 Both Outlander or Renegade.
This is the XMR 1000 rear differential found in 2013-2018 800R 850 1000/1000R XMR.
It will fit g2 bikes (500/650/800/850/1000) if you are upgrading you will need to shorten your shaft 1.75? or buy a kit from us, please see our other listings.
This differential has automotive style cut gears, tapered roller bearings, along with an overall larger gear size. There are a total of three bearings on the pinion gear giving it much more support over the standard rear differentials, this requires a shorter driveshaft, as mentioned earlier if you are swapping this in place of a standard differential.
Pinion spline count 20, standard differentials use 18 spline pinion shafts, that are smaller in diameter. If you are upgrading you will need a 20 spline end yoke to match.
In every way this is a beefier differential.
To bolt your driveshaft on this differential you will need a M10x1.25 16mm long bolt (not included)
Current part number 705503535
Old part number 705502546 705502178, 705502090- OUT OF STOCK
Can-am Outlander, Renegade or Commander 500 650 800 1000 6 Bolt HD rear Differential. This is an OEM Canam part used in many Generation 1 atvs. It has the bracket for the rear brake caliper on it. This is an updated version with much more substantial webbing for improved support. Fits: 2006-2011 Outlander and Renegade 500 650 800 800 2012 Outlander MAX 400 500 650 800 2011 2012 Outlander 800XMR 2006-14 Outlander 400 2011-2013 Commander 800 1000 Current Part Number 703501033 Previous Part Numbers 703500892 705502069 705501569 Interchanges with: 705500774 705500822 705501412 705500891 705501093 705501047 705501997 
Can-am Outlander, Renegade or Commander 500 650 800 1000 6 Bolt HD rear Differential.
This is an OEM Canam part used in many Generation 2 atvs.
It does not have the bracket for the rear brake caliper on it.
This is an updated version with much more substantial webbing for improved support.
Fits:
2012 Outlander and Renegade 800, 1000
2013 to 2018 500/570/650/800/1000 Outlander Renegade
2011-2013 Commander 800 1000
2013-2018 XMR 570 and 650**WILL NOT FIT** XMR 1000 or XMR 800
WILL NOT FIT ALL 2019 Models, please contact us if you have a 2019.Current Part Number 703501019
Previous Part Numbers 703500878, 705501896, 705501419, 705501993
SHIPS FREE TO THE LOWER 48 STATES NEW OEM Canam Parts OEM 14% LOWER LOW GEAR SET for most every 1000 Vtwins minus north american 2015 and newer outlander 1000/1000R This is the way to reduce the over all Low Gear ratio on your can-am 1000 running larger tires. This is the LOW RATIO for any Large Gearbox. The last picture shows a Large gearbox. This will not fit Small Gearboxes. 14% lower gear ratio than standard 1000 gear boxes (Maverick, Commander, Renegade, Outlander) Will also fit 800 Commander
1652 G2 Standard Rear Differential Rebuild Kit Please note, application alone is not accurate enough, please measure your parts before ordering! There are a few options for rebuild kits, please measure your parts before ordering!! OEM Rear Differential Gear set 10/36 Ring and Pinion gear set. The gears are straight cut as pictured. Paired with high quality aftermarket ball bearings along with double lip axle seals. If your differential has tapered roller bearings, this will not fit. This kit should be installed by an experienced technician. Shims are included as the gears will need to be set up in your cases. Note: the O rings are not included, this is a cost savings measure as they are generally reusable. This kit will only fit six mounting hole differentials. Measure your outer diameter of the pinion seal, it should measure 2 3/4" (70mm) Measure your outer diameter of your axle seals! They should measure close to 2 1/16″ (52mm) To further verify fitment you can measure your pinion pilot shaft, this should be 5/8″ (16mm) Please take the time to measure your parts before buying this will save time and restocking fees. Fits 2015 and newer G2 style ATV 500/570/650/800/850/1000/1000R NON-XMR style REAR differential. 570/650 XMR machines do not have the true XMR differential.
5280 Rear Differential Tapered Roller Bearings and Seal kit 1 Pinion Seal, 80mm outer diameter 2 Axle Seals, 52mm outer diameter 1 Thick Tapered Roller Bearing 3 Thin Tapered Roller Bearing 1 Needle Bearing These are High Quality aftermarket parts, as good or better than OEM! Brands include FAG, NTN, IKO, TIMKEN, KOYO, SKF, Dichtomatik. BRP does not sell these bearings alone, we have taken the guess work out of replacing these parts. Fits: 2019 to Current 650 and Larger ATVs 2013 to Current Outlander 1000/1000R XMR 2015 to Current Outlander 800/850 XMR 2016 to Current Renegade 1000R XMR some 2019 to Current 570 XMR (measure your parts to verify fitment) *** THIS WILL NOT WORK IN 2013-2018 650/570 XMR or 2011/2012 800 XMR machines. If you are unsure about fitment, please contact us! *** Fits differential part numbers: 705502808, 705502546, 705502178, 705502090
SHIPS FREE TO THE LOWER 48 STATES
Late G1 Early G2 Standard Rear Differential Rebuild Kit
There are a few options for rebuild kits, please measure your parts before ordering!!
OEM Rear Differential Gear set 10/36 Ring and Pinion gear set. The gears are straight cut as pictured.
Paired with high quality aftermarket bearings along with double lip axle seals.
This kit should be installed by an experienced technician. Ring gear shims are included as the gears will need to be set up in your cases, the pinion shims should remain unchanged
Note: the O rings are not included, this is a cost savings measure as they are generally reusable.
There are a few options for kits, please verify your differential uses this style of gears before ordering! This will only fit six mounting hole differentials.
Open up the differential! Check for two bearings total (one on each side) on the ring gear. If you only have two proceed to the next measurement.
Measure your outer diameter of your axle seals!
They should measure close to 1 3/4" (47mm)
To further verify fitment you can measure your pinion pilot shaft, this should be 9/16? (14mm)
The last pictures show this very clearly. Please take the time to measure your parts before buying this will save time and restocking fees.
SHIPS FREE TO THE LOWER 48 STATES This is the high end XMR rear differential replacement. The differential has all forged Carburized (case hardened) alloy gears, and high end bearings inside billet cases. These gears are set up to very specific tolerances, ready for years of abuse. These are sold with a six month warranty on the gears, lifetime on the cases. These gears require a break in period of 75-100 miles This is the aftermarket upgraded XMR 1000 rear differential found in 2013-18 1000/1000R XMR. You will have to clearance your surrounding brackets to install as this is a beefier case. The drain plug access hole in your frame may have to be enlarged also. It is also used in the G2 800 XMR & 850 XMR. It will fit g2 bikes (500/650/800/1000) if you are upgrading you will need to shorten your shaft 1.75" or by purchasing a conversion shaft, we can help with application, please ask! (G1 bikes will require further modifications to work). This differential has automotive style cut gears, tapered roller bearings, along with an overall larger gear size when comparing it to the standard differential. There are a total of three bearings on the pinion gear giving it much more support over the standard rear differentials, this requires a shorter driveshaft, as mentioned earlier if you are swapping this in place of a standard differential. Pinion spline count 20, standard differentials use 18 spline pinion shafts, that are smaller in diameter. In every way this is a beefier differential. Replaces current part numbers 705502178, 705502090 this does not have the ABS sensor hole.
Cam Am rubber bellow for front or rear differential. This is a brand new OEM rubber bellows. Part number 705400352
SHIPS FREE TO THE LOWER 48 STATES New Can Am Maverick or Commander Gear Box New Can-Am GEAR BOX this is the way to reduce the over all gear ratio on your can-am 1000 running larger tires. Current Part Number- 420686654 Replaces: 420686563, 420686562 & 420685807 NEW OEM Canam Part NOT A REBUILD, ALL NEW Brand New In The Box This is the LOW RATIO gearbox for the larger style gearbox equipped machines, please ask if you are unsure about fitment. **Top speed on our 2012 Commander 1000 is 62 mph (high range) with this gearbox and stock clutching and stock size tires** Gearbox ratios, this isn’t regurgitated info, this is us counting teeth inside of the gearbox. Ring and Pinon Gears 37/15=2.467 Intermediate 45/40=1.125 High Range 36/27=1.333 Low Range 46/17=2.706 Reverse 34/12=2.833 High Range Ratio 3.700 Low Range Ratio 7.509 Reverse Ratio 7.863- OUT OF STOCK
New Can Am ATV Low Ratio Small Gear Box / Transmission Will work on all Can-am Vtwin 500/570/650/800/850 Both Outlander or Renegade.- New Can-Am GEAR BOX
- Current Part Number- 420686612
- Replaces: 420684820, 420684824, 420684825, 420684827
- NEW OEM Canam Part NOT A REBUILD, ALL NEW
- This is the Low Ratio (6.4% Lower HIGH Range) gearbox than a standard 800 gearbox.
- This is found in Outlander or Renegade 500's, Outlander 650's and the Outlander 800R XMR
