NEW OEM Can-am Output Crank Shaft Seal This is the engine out put shaft seal, pressed into the crankcase PTO cover 34mm Inner Diameter 52mm Outer Diameter 8mm Thick Current Part Number 420631933 Replaces Part Number 420631932
OEM Can Am washer for plastic insert 707900133 This is ONLY for the washer Insert is NOT included (only pictured for reference) Part Number: 503189273
Brand New Genuine OEM Wear ring a must if you are replacing your pinion seal, these are the sacrificial parts that save your drive shaft from grooving! Will fit 18 and 20 Spline Yokes that are fully machined Part Number 705400036
BRAND NEW Can Am OEM Wheel Cap This is for a set of Four (4) Caps Part Number 705400928 There is more than one style. Please verify that this is the correct style BEFORE ordering.
NEW Prop Shaft Low profile pair of clamps for 715900118 boot. Clamps also work for G2 front shaft boot 705401093. The last few pictures show the clamps loose, then installed nice and tight. Sold in pairs enough to do one boot.
Rugged wheels spacers are made from T6061 aluminum alloy and are precisely CNC machined for accurate dimensions. Spacers can be direct bolt on and can use OEM studs. If you are looking to widen the stance of your machine, clear larger tires or get some new wheels. These spacers are just what you need. These spacers are sold as a pair. One inch thick The bolt pattern is 4x137mm M10 studs Part number PAWS-1035
Rugged wheels spacers are made from T6061 aluminum alloy and are precisely CNC machined for accurate dimensions. Spacers can be direct bolt on and can use OEM studs. If you are looking to widen the stance of your machine, clear larger tires or get some new wheels. These spacers are just what you need. These spacers are sold as a pair. 1.5 inch thick The bolt pattern is 4x137mm M10 studs Part number PAWS-1036
Rugged wheels spacers are made from T6061 aluminum alloy and are precisely CNC machined for accurate dimensions. Spacers can be direct bolt on and can use OEM studs. If you are looking to widen the stance of your machine, clear larger tires or get some new wheels. These spacers are just what you need. These spacers are sold as a pair. Two inch thick The bolt pattern is 4x137mm M10 studs Part number PAWS-1037
M8x1.25×70 Bolt. m8-1.25x70mm Used to open the secondary clutch on many Can-am ATV’s & SXS’s Simple tool, trusted seller. Or just use these specs and head to your hardware store.
Spicer Brand U joint for front drive shafts Fits: G1 Renegade and Outlander . Also works on Outlander 400 Rear shafts. Maverick/Commander front driveshafts Will not fit: Maverick X3/Sport/Trail or Defender Includes clips, and grease fitting. Pro tip: Install grease fitting before pressing in u joint. Install u joint in a manner where you can still grease the joint in chassis. Replaces OEM : 715900325 703000023 703000024 703500002 703500135 703500607 703500814
SHIPS FREE TO THE LOWER 48 STATES Set of Bearings and Seals to Rebuild Your Front Differential on Your Can-Am Fits Most Can-Am Models from 2007-Current (WILL NOT FIT Maverick X3/Sport/Trail or Defender) This Kit has High Quality Aftermarket Bearings which are: Timken, SKF, NSK, KOYO, Nachi Comes with: 2 - Carrier Bearings- SKF Brand 2 - Axle Bearings- OEM NSK Japan made 2 - Axles Seals- Timken 1 - Inner Pinion Bearing- Nachi Japan made 1 - Large Pinion Bearing- Koyo Japan made 1 - Pinion Seal- Sale!
New take off gearbox side, 20 spline yoke. This fits on large gearboxes output shafts. 20 spline yoke partially machined to accept a protector ring. This is the forward most yoke on the REAR driveshaft. Works with 398 U joints. found on Vtwin rear driveshafts. Part number 715900129 replaces 705501373 and 715900234
Have Questions?
Our staff is available to answer questions
canampartsguy@gmail.com
1340 Okray Ave.
Plover, WI 54467
jared@canampartsguy.com
Cant find What you're looking for?
Visit our 
store!
2016 Can Am Parts, LLC. All rights reserved.