FREE SHIPPING TO THE LOWER 48 STATES New OEM clutch inner cover Will fit on the following 2016-2019 Defender HD8 and HD10 2018-2019 Maverick Trail 800R and 1000R 2019 Maverick Sport 1000R Does not included mounting hardware or o-rings. Comes as bare cover
New OEM Torx Screws Comes as a set of 11 Will fit on the following 2016-2019 Defender HD8 and HD10 2018-2019 Maverick Trail 800R and 1000R 2019 Maverick Sport 1000R
FREE SHIPPING TO THE LOWER 48 STATES New OEM cover Will fit the following 2016-2019 Defender HD8 and HD10 2018-2019 Maverick Trail 800R and 1000R 2019 Maverick Sport 1000R Old part number 420212502 New part number 420212500 O-ring and drain plug cap are NOT included
New OEM Cap Fits on cover 420212500 Comes with 0-ring 420250050 Fits the following machines 2016-2019 Defender HD8 and HD10 2018-2019 Maverick Trail 800R and 1000R 2019 Maverick Sport 1000R
New OEM Gasket Will fit the following 2016-2019 Defender HD8 and HD10 2018-2019 Maverick Trail 800R and 1000R 2019 Maverick Sport 1000R
New OEM Defender, Maverick Trail/Sport Clutch Cover Kit Will fit the following 2016-2019 Defender HD8 and HD10 2018-2019 Maverick Trail 800R and 1000R 2019 Maverick Sport 1000R Kit includes Outer Cover 420212500 Inner Cover 420212600 Gasket 420450400 O-ring set 420450431/420430408 Bolt set 420441575 Drain plug with O-ring 420441820
EPI brand Wheel bearing Greaser Tool for bearings with 30mm inner diameter Quick and easy way to extend the life of your wheel bearings 10 pumps of marine rated grease into a new wheel bearing will extend the bearing’s life High quality CNC machined with precision drilled grease channel Axle stub needs to be removed to use the tool. Part numbers: 3811-0094 CA30MMGREASER-O
Brand new Genuine OEM air filter Fits 2016-Current Defenders HD5, HD8, and HD10’s both 3 and 6 seat machines Fits 2018-Current Maverick Trail 800 and 1000’s Fits 2019-Current Maverick Sport 1000 Part number 715900394
New Genuine OEM Rear Differential Lock Switch Only works on models with turf mode
Works on 2017-2020 Defenders
2018-2020 Maverick Trail
019-2020 Maverick Sport
- OUT OF STOCK
New Genuine OEM Can Am Switch Work/Normal/Eco Mode Switch Fits 2016-2019 Defenders 
New Genuine OEM Can Am Ignition Switch
Fits:
2016-2020 Defender
2018-2020 Maverick Trail
2019-2020 Maverick SportPart numbers 710004198 710007870
New Genuine OEM Can Am speedometer Fits 2016-2017 Defenders These are designed to auto sync with your machine if it does not auto sync you will need to use BUDS to program the dash to your machine. This is a new dash with 0 miles the Engine hours stay with the ecu, be sure to record your miles for your own records. The dash is set from the factory in km/h and will require BUDS programming to change it to mph. Part number 710005135
NEW Chrome Conical Taper M10 Lug Nut Set of 16 M10x1.25 thread size 60 Degree taper 14mm Hex head size, great for use with aftermarket wheels where socket space is a concern These will work on every Canam ATV since 2006 and most every Canam sxs Will not fit the Maverick X3 12mm wheel studs. Part numbers: 57-94121, ALUG14BX
NEW Black Conical Taper M10 Lug Nut Set of 16 M10x1.25 thread size 60 Degree taper 14mm Hex head size, great for use with aftermarket wheels where socket space is a concern These will work on every Canam ATV since 2006 and most every Canam sxs Will not fit the Maverick X3 12mm wheel studs. Part numbers: 57-94121B, ALUGB14BX- OUT OF STOCK
Genuine OEM Radiator
2016-2020 Defenders HD5, HD8, and HD10
2017-2020 Defender Max HD8 and HD10
Part number 709200951 replaces 709200533
Genuine OEM tail light 2016-2020 Defender HD5 HD8 and HD10 2017-2020 Defender Max HD8 and HD10 Works on either left or right side Part number 710004257
New Genuine OEM fan 2016-2020 Defender HD5, Hd8, and HD10 2017-2020 Defender Max HD8 and HD10 Part Number 709200534
NEW SEIZMIK STRIKE Side mirror set Both drivers and passengers side mirrors Pro Fit mounts for the goofy looking D shaped with a channel roll cage will not fit round cages We test fitted these on our defender with the OEM flip glass windshield, there is enough room for the bracket to mount and the windshield to seal as it should. Features: Adaptive 360 Bracket Rotation: Will accommodate any angle roll cage pillar & provide optimal viewing position, so you can mount it high or low and adjust to perfect position every time Full Breakaway Geometry: Designed to break away during impacts to prevent damage Convex mirrors more than double your field of rear view High-Impact ABS Plastic Housing: Resists damage Ball Socket Joint: Provides a broad range of viewing angles Heavy-Duty Steel Mounting Clamp: Low mass design provides maximum strength and durability Convex Mirror Surface: provides wider viewing ranger and image stabilization Shatter Resistant Safety Glass Position Tension Adjustment Bolt: Always be able to keep it tight as new UNLIMITED LIFETIME WARRANTY CANAM Cage Styles Defender: Pro Fit Cage Maverick Trail/Sport: Pro Fit Cage OG Maverick/Commander: Round 2.0” Part number 18093
Drive Belt Can Am Fits: 2017-2020 Maverick X3 900HO Turbo R Turbo RR 2017-2020 Maverick Trail/Sport 800R, 1000, 1000R 2016-2020 Defender HD10/HD8
Replaces OEM # 422280651 / 417300383 / 422280654 / 422280652 Gates Part number 48R4289 If you have fitment questions, please ask, we are here to help.
IF YOUR MAVERICK HAS A REAR DRIVESHAFT (OG MAVERICK) THIS BELT WILL NOT FIT.
FEATURES AND BENEFITS
Designed for the most demanding, turbo-charged off-road CVT applications. With Gates proprietary materials and design, G-Force™ RedLine™ CVT belts handle extreme temperatures with excellent heat recovery, while maximizing load and torque capacity - making it one of the most efficient CVT belts currently on the market.- First on the market to utilize Ethylene Elastomer compound to address the needs of larger SxS and high-horsepower ORVs in tough riding conditions.
- Next-generation EE compound offers maximum transverse stiffness and heat resistance, resulting in higher load capacity, higher peak torque capacity, less “heat fade” and less speed loss.
- Delivers 75% greater dynamic axial stiffness on average, up to 50% lower speed losses and better recovery from temperatures up to +170°C (+338°F) without power loss.
- Unmatched Temperature Capability – Runs cooler, resists glazing for better recovery and reduced cracking/chunking out after running at temps exceeding +149°C (+300°F).
- Extended Belt Life – Belt life increased 100-300% versus aftermarket competitive belts in severe duty lab test conditions and in field testing.
- Higher Power Capacity – Reduced speed (rpm) loss by 50% under high loads and increased load capacity by >10% compared to other aftermarket belt.
DON’T BREAK YOUR BELT. BREAK IT IN.
If you don’t break the belt in properly, you’ll find yourself shredding the belt instead of the terrain. In fact, most powersports belt failures can be attributed to improper break-in and clutch adjustment – or not breaking in the belt at all. Follow these steps to ensure the best performance and longest life from your G-Force™ belt.
1. Clean the clutches according to manufacturer specifications and clean the sheaves with a Scotch-Brite™ pad. Remove old belt residue, glazing, oils, and debris with alcohol or acetone on the clutch sheave area. Be sure your breather tubes are free of any belt material (broken belt material gets everywhere)
2. Install and Break It In. Perform two heat cycles (10-15 minutes each) at +27°C (+80°F) at 30-40 mph (2-wheel drive) with cover installed. Bring the belt temperature down to normal operating temperatures, then shut down and let cool for 30 minutes. Repeat the process a second time. If belt installation is at a temperature of +16°C (+60°F) or below, perform two heat cycles in 20 minutes at 30-40 mph (2-wheel drive) with cover installed. Bring the belt temperature down to normal operating temperatures, then shut down and let cool for 30 minutes. Repeat the process a second time. Conservatively run through the entire shift range, without exceeding ¾ throttle. Bring the belt back to normal operating temperature (15 minutes) then shut down and completely cool the belt for 30 minutes. Repeat the process.
New Genuine OEM Removable on dash toolbox 1.7 Gal (6.3 L) of storage Water resistant to keep the inside safe and dry Fits 2016-2020 Defender and Defender Max Part number 715004344
New Genuine OEM 4 Gallon polypropylene injected storage bin Great for storing ropes, tow straps, and winch accessories Easy install (takes just a few minutes) Part number 715003399- OUT OF STOCK
New Genuine OEM 2 Gallon (8L) polypropylene injected storage bin Watertight to keep ice and drinks cold Easy install and removal for quick and easy cleaning Part number 715003446 - OUT OF STOCK
New Genuine OEM 3.7 Gallon (14L) polypropylene injected storage bin Quick and easy install Water resistant Part number 715003314 
New Genuine OEM Works on 2016+ Defender and Defender Max Works on both driver and passenger doors Part number 710004979 replaces 705800048
Air Pressure sensor, this goes in the Black plastic Intake manifold. Will work on any 2006 to current Can am Outlander, Renegade, Commander, Maverick, Defender 500 570 650 800 850 1000 XT XMR MAX or XXC The Manifold Absolute Pressure sensor or MAP sensor is a sensor that is attached to the intake manifold. The MAP sensor responds to changes in the intake manifold pressure (vacuum) and provides a reading of engine load. How it works is 5 volts DC is supplied to the sensor from the ECU. Inside the MAP sensor there is a resistor that moves in relation to intake manifold pressure. The resistor varies the voltage between about 1V to 4.5V (depending on engine load) and that voltage signal is returned to the PCM to indicate manifold pressure (vacuum). This signal is essential for the PCM to determine fuel delivery. Part numbers: 420874650 707000564 707000995 0 261 230 030 ALFA ROMEO 46553045 ALFA ROMEO 46533518 CHERY S21-3614021 FIAT 46553045 FIAT 77364869 FIAT 7084986 FIAT 0000046553045 FIAT 46533518 LANCIA 46533518 LANCIA 0000046553045 LANCIA 46553045 MOOSE 2120-0994 PROTON PW810694 ROTAX (BOMBARDIER-ROTAX GMBH) 874 650 SCANIA 5166434
New Genuine OEM Fits 2016-2020 Defender and Defender Max Secures items in the dash storage area Not compatible with defrost, heat & ventilation system Sold in pairs
New Genuine OEM Works on 2014-2020 Commander and Commander Max (2011-2013 Do not have a oxygen sensor) 2013-2018 Maverick and Maverick Max 2017-2020 Maverick X3 and Maverick X3 Max 2018-2020 Maverick Trail 2019-2020 Maverick Sport 2017-2020 Defender and Defender Max If your machine has ECO mode it will have a oxygen Sensor from factory Part number 707600872
New Genuine OEM Wide angle convex mirror Can be used with or without windshield, roof, or cab enclosure Part number 715003638- OUT OF STOCK
New Genuine OEM Comes with 3 programmable keys Work key: Limits vehicle speed to 40 kph (25 mph) but does not limit engine torque. Normal key: Defender models: Limits vehicle speed to 70 kph (44 mph) and 10% torque reduction. Maverick Trail & Maverick Sport models: Limits vehicle speed to 70 kph (44 mph) and 50% torque reduction. Performance key: No restrictions. Part number 715002458 
Dual USB Power Outlet Kit A simple upgrade kit, plug and play Product Number: 219400510 replaces the existing 12v power outlet on your machine: 710001248
NEW AFTERMARKET STARTER VTWIN Will come as pictured Part Numbers: 420684560 420684562 420684568 420684566
NEW AFTERMARKET STARTER SPRAG VTWIN Starter Clutch One Way Bearing for Can-Am Will come as pictured Replaces OE Part Numbers:420659112 420659111 420659261 420659263 420659260
NEW AFTERMARKET OIL COOLER VTWIN Fit on the "big block" cases Will come as pictured Part Numbers: 420890180
Full rear mesh screen reduces windshield backdraft for added cabin comfort. Installs quick and easily on roll cage. White Can-Am logo at top, to help maintain clear view. Part Number 715002851
New OEM Cylinder Head Gasket Fits Defender HD5 Outlander 450 and 850 Renegade 850 Will come as pictured Part number 420450340
One spark plug boot, this is used on many applications 2020 and older, if you are unsure on fitment, please contact us.
Part number 420265248
Replaces 710000041 and 420265240
Have Questions?
Our staff is available to answer questions
canampartsguy@gmail.com
1340 Okray Ave.
Plover, WI 54467
jared@canampartsguy.com
Cant find What you're looking for?
Visit our 
store!
2016 Can Am Parts, LLC. All rights reserved.