High quality Timken axle oil seal. Fits ATV rear differentials 2006-2014 To be 100% sure on fitment, measure your outer diameter on your seal, it should read 47mm This seal has a 30mm inner diameter 47mm outer diamter and is 7mm thick. Replaces OEM 705500751 705501196 and 705501996 Order qty two per machine.
New Can Am Maverick 1000R Rear Differential KIT ready for your custom install. New OEM Can-Am Rear Differential New OEM Yoke Updated style that does not require a wear ring (uses standard 398 U joint) New Bolt and washer Replaces Rear differential in any Maverick/Maverick Turbo (non X3/Sport/Trail) Largest and strongest rear differential found in Can-am’s 10/36 Gear set, that is a 3.60:1 ratio, same since at least 2006 Pinion shaft 20 spline Current Part Number 705502275 Old Part Numbers 705501912 705501958
OMC trunk seal for G2 Outlander This is an improved design over factory, this is much thicker and denser foam than the OEM gasket WILL NOT FIT G2L (models with steel racks) Replaces OEM part numbers: 293250275 219704369 293200163
Aftermarket Four wheel drive servo motor.
This is what engages the sliding collar putting power to the front differential.
Replaces oem 715900614 4151 29174 420891087
- OUT OF STOCK
Made in the USA Specialized ATV, made some strong, tough rods that will hold up to whatever kind of riding you like. 6061 Billet Rods with 5/8 heim joints and all the needed hardware to install. 1 year warranty from date of purchase, directly from SPATV 1 set comes with 2 tie rods and complete assembled heims and hardware. Fits G2 Outlanders and Renegades 2012+ (even the wider 2019+ machines) 
Fits G2 ATV's Kit includes: Four Wheel Studs, Four Lug Nuts, Four Rotor Bolts Replaces OEM numbers: 250300048 250300643 250300642 250100100 250100184 235381646- OUT OF STOCK
Features:
Cable adapter and fasteners constructed of highest quality stainless steel
Gold anodized aluminum throttle lever can be operated with one finger for safer side hilling
Safety features include rubber accordion boot (keeps moisture out of cable housing) and safety pin (locks left throttle from unwanted use)
Kit includes all hardware, allen wrenches and instructions for installation in approximately 20 minutes
Part Number 12-71042
Brand Number: 007-1011A 
Can Am Commander seat bottom cover Solid Black in color Brand new OEM Part Number: 708000674 708001103
NEW OEM High-Performance Metallic Brake Pads Designed to handle demanding riding conditions with challenging braking environments One caliper set, fits front or rear calipers on G2 ATVs Part number 715900249 interchanges with 705601014
Plain bearing half 40 X 43 X 15 This fits into one side of the connecting rod. part number 420233980
New OEM Secondary Clutch Outer Bearing
Current Part Number 420932421
Replaces 420932426 and 711932426
52mm Outer Diameter
25mm Inner Diameter
15mm Thick
- Sale!
New take off gearbox side, 20 spline yoke. This fits on large gearboxes output shafts. 20 spline yoke partially machined to accept a protector ring. This is the forward most yoke on the REAR driveshaft. Works with 398 U joints. found on Vtwin rear driveshafts. Part number 715900129 replaces 705501373 and 715900234 
Brand NEW OEM Tail Light Assembly Found in G2 Renegade and Outlander, Commander and Maverick. Fits left or right. Part Number 710001645
Black wrap around wind deflector set with mounting kit. Fits Outlander, Renegade, & DS450. Both are brand new. Part numbers 715001378 715001706
Specialized ATV HD Front Drive Shaft Fits G2 ATVs Replaces OEM part numbers: 705400913 705401032 Ships as pictured 25mm diameter shaft, this is huge compared to the OEM part. MADE IN USA
New Genuine OEM Fits on: 2017-2019 Outlander and Renegades 2020 Outlander 650 STD DPS XT XMR 2020 Outlander 6×6 650 or 1000 2020 Renegade 570 XMR 3 position headlight switch OFF/Low/High beam Part number 710008837 replaces 710005070 Will come as pictured- OUT OF STOCK
EPI roller kit Part number WE210933 The rollers in this kit were designed by The Clutch Guys to replace the stock composite rollers. They are CNC machined and hardened for a long service life. The stock composite rollers that Can Am uses tend to flat-spot very quickly, resulting in greater friction and reduced primary clutch reaction. Upgrade to these custom metal rollers for improved clutch function. The kit includes 6 custom metal rollers with bushings, 6 roller pins and 12 roller washers Replaces oem numbers: 420233893, 417223257, 420229995, 417223767, 420626230, 420626231 
Heavy-duty ball joint kits feature durable steel-on-steel design and an adjustable end cap, which allows slop to be taken up as they wear
Greased zerk fitting for easy grease delivery
Replaces OEM part numbers: 706201393 706201576 706202045
G2 ATV’s Commander, Maverick, Maverick X3, Maverick Sport, Maverick trail
Unsure on fitment, please ask!Moose Racing number 0430-1035
Drive Belt Can Am Fits: 2017-2020 X3 Maverick Turbo R Turbo RR 900HO 2017-2020 Maverick Trail/Sport 800R, 1000, 1000R 2016-2020 Defender HD10/HD8 OEM # 422280651 / 417300383 / 422280654 / 422280652IF YOUR MAVERICK HAS A REAR DRIVESHAFT (OG MAVERICK) THIS BELT WILL NOT FIT.FITMENT QUESTIONS?? PLEASE ASK!World’s Best Belt Line- Latest generation heavy-duty, high-twist Aramid Fiber cord for HIGH HORSEPOWER TENSILE LOAD requirements. Making it the strongest belt on the market.
- Highest shock load rating to date being able to withstand the power of the 400hp machines.
- Increased top cog pressure load design that increases sidewall rigidity, prevents top cog bowing, but still allows for increased rotational flexibility.
- Bottom cog uses HIGH MODULOUS RUBBER COMPOUND (BZX1) for better heat resistance and heat dissipation.
- Bottom cog is impregnated with short Aramid Fibers for better belt-to-sheave adhesion and reduced overall belt temperature.
- Latest bottom cog design for greater rotational efficiency at full shift.
- Precision ground sidewall angle (SCUFFING) for smooth engagement, increased power transfer and lower operating belt temperature.
- Aramid Fiber cord, versus polyester, wraps over bottom cogs for increased bottom cog strength.
- Increased cord pop-out resistance.
EPI Lower Ball Joint Fits: G1 Outlanders 400 500 650 800 Replaces OEM: 706200444 This style of ball joint bolts to the lower control arm. If you are unsure of fitment, please ask! 2006 - 2014 Can-Am Outlander 400 2007 - 2012 Can-Am Outlander 500 2008 - 2012 Can-Am Outlander 650 2006 - 2011 Can-Am Outlander 800 2006 - 2013 Can-Am Outlander Max 400 2007 - 2013 Can-Am Outlander Max 500 2007 - 2012 Can-Am Outlander Max 650 2006 - 2012 Can-Am Outlander Max 800
New Genuine OEM Can Am Ignition Switch
Fits:
2016-2020 Defender
2018-2020 Maverick Trail
2019-2020 Maverick SportPart numbers 710004198 710007870
Replaces OEM 703500836 Japan Made Uncaged Needle Bearing 20X27X15mm Needle Bearing for XMR rear differential pinion gear
Wind deflector mounting kit with hardware. Fits Outlander Renegade & DS450. For use with OEM wind deflectors This is just the mounting kit. Part number 715001378 No wind deflectors included.
- OUT OF STOCK
SHIPS FREE TO THE LOWER 48 STATES New genuine Can-am rear prop shaft for outlander 1000 xmr. (MAX length minus 1.75”) This is an oem part, we do not cut, phase, balance or otherwise modify this shaft. It will work on 2012-14 Outlander 1000 MAX ATV's with the XMR rear differential also. 20 Spline Gearbox Yoke 20 Spline Differential Yoke Current Part number: 703500989 Previous Part number: 703500859, 705501720, 703500927 
NEW AFTERMARKET STARTER SPRAG VTWIN Starter Clutch One Way Bearing for Can-Am Will come as pictured Replaces OE Part Numbers:420659112 420659111 420659261 420659263 420659260
Six Weights 12 gram each for CVtech Trailbloc Primary Part numbers: 0935-2004 0901-7104
Canam CVT Cover Kit Commander/Maverick 1000R
Please look at pictures to verify fitment.
This outer cover has two breather holes, one in front of the primary, one on the secondary.
This outer cover is the factory replacement for 420612319, some aftermarket clutches will not clear the new breather hole style you may need to modify this cover or backdate it to the 420612313 style with out the secondary breather.
Please look at pictures to verify fitment.
Fits:
Commander 1000R two seat 2018-2020
Commander 1000R MAX four seat 2018
Maverick 1000R two seat 2014-2018
Maverick 1000R MAX four seat 2014-2018Will not fit:
2015-2018 Maverick 1000R Turbo
2017-2018 Maverick 1000R XMRInner cover 420612304
Outer cover 420212286
13 Hex head CVT housing bolts 420440568
Gasket 420430126
O-rings – 420430407 and 420631087
Hex Bolts – 420440207
Also has a nut and washer – 232561434, 224061121
Nylon drain plug and clamp
NEW Genuine OEM Coolant Temperature Sensor This screws into the cylinder head Part Number 278002895
Can-am Commander style Outer CVT cover belt box Please check your cover before ordering, we can help if you do not know what to look for. This is the updated 13 bolt cover with the heat shield. Fits: Commander 800R two seat 2011-2020 Commander 800R MAX four seat 2016 Commander 1000 two seat 2011-2017 Part number 420612472
Brand New Genuine OEM ignition key switch for Outlander G1 or Renegade G1 Does not require BUDS tuning to swap out, your current DESS key will turn in this. The ignition switch is just a reader of the coded key. Key sold separately. Old Part Numbers 710000728 and 710001421
NEW OEM Can-am Output Crank Shaft Seal This is the engine out put shaft seal, pressed into the crankcase PTO cover 34mm Inner Diameter 52mm Outer Diameter 8mm Thick Current Part Number 420631933 Replaces Part Number 420631932- OUT OF STOCK
SHIPS FREE TO THE LOWER 48 STATES 0934-3019 Moose Racing Gasket Kit Fits Outlander/Renegade 800 models. Complete kit with oil seals. Center case gasket Magneto Cover Gasket PTO Cover Gasket Two Cylinder base Gaskets Two Cylinder Head Gaskets Two Valve Cover Gaskets Water Pump Cover Seal (kit does not come with mechanical seal) 
Can-am Outer CVT Cover, belt box. This is the updated 13 bolt cover. Works with 7 or 13 bolt inner covers. This will fit on any 2006-current v twin ATV, Renegade or Outlander, 500 650 800 or 1000. If you have a a stud with a nut retaining your primary clutch this cover does not have the depth needed. Many 1000R machines use a stud/nut in place of the bolt. Unsure on fitment, please ask! This will keep the water out! 13 Cover bolt holes Current Part number is: 420611397 Replaces: 420611395, 420611390, 420611391, 420611393
SHIPS FREE TO THE LOWER 48 STATES Late G1 Early G2 Standard Rear Differential Bearing and Seal Kit High quality aftermarket bearings along with double lip axle seals. Bearing and Seal Brands include: Nachi, KOYO, NTN, Timken The large case sealing and pinion gear O-rings are NOT included as a cost saving measure, these O-rings are reusable if not damaged. There are a few options for kits, please verify your differential uses this style of gears before ordering! This will only fit six mounting hole differentials. Open up the differential! Check for two bearings total (one on each side) on the ring gear. If you only have two proceed to the next measurement. Measure your outer diameter of your axle seals! They should measure close to 1 3/4" (47mm) To further verify fitment you can measure your pinion pilot shaft, this should be 9/16″ (14mm) The last pictures show this very clearly. Please take the time to measure your parts before buying this will save time and restocking fees.
OEM CANAM BRP Exhuast Muffler Clamp Part Number 293650177 Fits 2.25" OD pipe
These dashes are found on many machines.
2014-2017 Maverick, Commander, Renegade and Outlander models with the Standard Digital Dash Mount This is the factory Gauge/Screen.
The dash is designed to auto pair, but sometimes it will not auto pair and you will have to program them together with buds software. This can be done at your local dealer or you can send in your ecu, key(s), and DPS (power steering) to us for programming. Contact for more information.
It will display 0 miles, please record your current miles for your records.
Current part number: 710005087
Replaces part numbers: 710003851 710003924 710005024 710005208
Have Questions?
Our staff is available to answer questions
canampartsguy@gmail.com
1340 Okray Ave.
Plover, WI 54467
jared@canampartsguy.com
Cant find What you're looking for?
Visit our 
store!
2016 Can Am Parts, LLC. All rights reserved.