New short wiring harness for rear tail lights Will need to be wired in to work. This plugs in to Tail light part number 710001645 Fits: G2 ATV's with dual tail lights, Commanders, and Mavericks (non X3/Sport/Trail)
New OEM Cap Fits on cover 420212500 Comes with 0-ring 420250050 Fits the following machines 2016-2019 Defender HD8 and HD10 2018-2019 Maverick Trail 800R and 1000R 2019 Maverick Sport 1000R- OUT OF STOCK
NEW OEM ignition switch. Part number 710008400 replaces 710002327 710003847 It will work on all 2011 to 2019 Commanders, 2012 to 2016 Generation 2 Outlanders and Renegades and 2013 to 2018 Mavericks. Key sold separately.
Can-am Rubber Trailing Arm cover and Oetiker clamp for your G1 Outlander or Renegade Will only work on the gen 1 Outlander and Renegades 2006-11 and some 2012 models. If you are unsure on fitment, please ask. You will need to order qty 2 to replace both sides. Genuine OEM parts Part Numbers: 706000222 706000749 293650162
This is the XMR 1000 rear differential found in 2013-2018 800R 850 1000/1000R XMR.
It will fit g2 bikes (500/650/800/850/1000) if you are upgrading you will need to shorten your shaft 1.75? or buy a kit from us, please see our other listings.
This differential has automotive style cut gears, tapered roller bearings, along with an overall larger gear size. There are a total of three bearings on the pinion gear giving it much more support over the standard rear differentials, this requires a shorter driveshaft, as mentioned earlier if you are swapping this in place of a standard differential.
Pinion spline count 20, standard differentials use 18 spline pinion shafts, that are smaller in diameter. If you are upgrading you will need a 20 spline end yoke to match.
In every way this is a beefier differential.
To bolt your driveshaft on this differential you will need a M10x1.25 16mm long bolt (not included)
Current part number 705503535
Old part number 705502546 705502178, 705502090
Left Side Front or Rear for G2 ATV 2012 with dual piston calipers 2013-19 To current G2/G2L One Caliper Set Part number: DP515 1721-1448 Replaces OEM # 715900248 705601015 DP Brakes Brake Pads are designed with sintered metal compounds to give your ATV high-tech performance in all conditions Pads have a quick break-in period so you get maximum performance fast DP Brakes design and materials ensure consistent, hard stops and fade-free performance Sintered metal compounds outlast more conventional organic or aramid fiber pads
Cam Am rubber bellows for front differential or rear differential This is a brand new OEM rubber breather and a OEM Oetiker Clamp Bellows Part # 705400352
SHIPS FREE TO THE LOWER 48 STATES Fits all 500, 650, 800, 800R, 570, 850, 1000, 1000R and 1000R turbo Mavericks Outlanders, Renegades, and 2020 & Prior Commanders. Replaces OEM part numbers 715000302, 422280360, 715900212, and 422280364. This will not fit: Defenders, Maverick X3 or Maverick Sport/Trail World’s Best Belt Line- Latest generation heavy-duty, high-twist Aramid Fiber cord for HIGH HORSEPOWER TENSILE LOAD requirements. Making it the strongest belt on the market.
- Highest shock load rating to date being able to withstand the power of the 400hp machines.
- Increased top cog pressure load design that increases sidewall rigidity, prevents top cog bowing, but still allows for increased rotational flexibility.
- Bottom cog uses HIGH MODULOUS RUBBER COMPOUND (BZX1) for better heat resistance and heat dissipation.
- Bottom cog is impregnated with short Aramid Fibers for better belt-to-sheave adhesion and reduced overall belt temperature.
- Latest bottom cog design for greater rotational efficiency at full shift.
- Precision ground sidewall angle (SCUFFING) for smooth engagement, increased power transfer and lower operating belt temperature.
- Aramid Fiber cord, versus polyester, wraps over bottom cogs for increased bottom cog strength.
- Increased cord pop-out resistance.
Front and Rear Seals for the engine thru shaft. These are high quality Timken brand seals Replaces OEM part numbers: 420430589, 420430580, 420850055
New XPS SAE 75W-90 and 75W-140 Synthetic Gear Oil Kit. Enough to do a complete service on the front differential, rear differential, and gear box 1 U.S QT 946ml per bottle Listing is for 2 Quarts. See your owners manual before ordering to make sure you order the correct weight for your Can Am Part number 779160 and 779158
SHIPS FREE TO THE LOWER 48 STATES Fits all 500, 650, 800, 800R, 570, 850, 1000, 1000R and 1000R turbo Mavericks Outlanders, Renegades, and 2020 & Prior Commanders. Replaces OEM part numbers 715000302, 422280360, 715900212, and 422280364. This will not fit: Defenders, Maverick X3 or Maverick Sport/Trail Gates Part number 30R3750 Do not confuse this with the carbon or standard g-force, this is the newly developed for the 2020 season.DON’T BREAK YOUR BELT. BREAK IT IN.FEATURES AND BENEFITS Designed for the most demanding, turbo-charged off-road CVT applications. With Gates proprietary materials and design, G-Force™ RedLine™ CVT belts handle extreme temperatures with excellent heat recovery, while maximizing load and torque capacity ― making it one of the most efficient CVT belts currently on the market.- First on the market to utilize Ethylene Elastomer compound to address the needs of larger SxS and high-horsepower ORVs in tough riding conditions.
- Next-generation EE compound offers maximum transverse stiffness and heat resistance, resulting in higher load capacity, higher peak torque capacity, less “heat fade” and less speed loss.
- Delivers 75% greater dynamic axial stiffness on average, up to 50% lower speed losses and better recovery from temperatures up to +170°C (+338°F) without power loss.
- Unmatched Temperature Capability – Runs cooler, resists glazing for better recovery and reduced cracking/chunking out after running at temps exceeding +149°C (+300°F).
- Extended Belt Life – Belt life increased 100-300% versus aftermarket competitive belts in severe duty lab test conditions and in field testing.
- Higher Power Capacity – Reduced speed (rpm) loss by 50% under high loads and increased load capacity by >10% compared to other aftermarket belt.
If you don’t break the belt in properly, you’ll find yourself shredding the belt instead of the terrain. In fact, most powersports belt failures can be attributed to improper break-in and clutch adjustment – or not breaking in the belt at all. Follow these steps to ensure the best performance and longest life from your G-Force™ belt.
1. Clean the clutches according to manufacturer specifications and clean the sheaves with a Scotch-Brite™ pad. Remove old belt residue, glazing, oils, and debris with alcohol or acetone on the clutch sheave area. Be sure your breather tubes are free of any belt material (broken belt material gets everywhere)
2. Install and Break It In. Perform two heat cycles (10-15 minutes each) at +27°C (+80°F) at 30-40 mph (2-wheel drive) with cover installed. Bring the belt temperature down to normal operating temperatures, then shut down and let cool for 30 minutes. Repeat the process a second time. If belt installation is at a temperature of +16°C (+60°F) or below, perform two heat cycles in 20 minutes at 30-40 mph (2-wheel drive) with cover installed. Bring the belt temperature down to normal operating temperatures, then shut down and let cool for 30 minutes. Repeat the process a second time. Conservatively run through the entire shift range, without exceeding ¾ throttle. Bring the belt back to normal operating temperature (15 minutes) then shut down and completely cool the belt for 30 minutes. Repeat the process.
NEW Bearing and Seal Kit for Can-Am Outlander and Renegade Rear Trailing Arms
They fit G2 Models (2012+)
Replaces part numbers 293350145 706000826 293200132 293200144
This is enough bearings and seals to do both rear arms (some newer models only use half the bearings)
These are high quality KOYO bearings and SKF/Dichtomatik seals.
Can-am Rear G2 2012 and newer prop shaft. All New All OEM Shaft OEM U-joints, with OEM gearbox seal protector installed. Correct shaft for Single Seat (SWB) 2012-14 1000 Outlander or Renegade with 1000 XMR rear differential. WILL NOT WORK ON 2015 Outlander 1000/1000R and newer as these have the smaller gearbox. Direct replacement for 2016-Current Renegade 1000R XMR **Please note, this is the most updated shaft and does not require a wear ring on the differential side of the shaft. The last two pictures illustrate this.** 20 Spline Gearbox side yoke 20 Spline Differential side yoke Current Part number: 703500990 Previous Part number: 703500928 703500901
New OEM can-am input or output seal for small gear boxes You will need two per gearbox. 32mm inner diameter 47mm outer diameter 7mm thick Current Part Number 420950089 Replaces Part Number 420950087
1652 G2 Standard Rear Differential Rebuild Kit Please note, application alone is not accurate enough, please measure your parts before ordering! There are a few options for rebuild kits, please measure your parts before ordering!! OEM Rear Differential Gear set 10/36 Ring and Pinion gear set. The gears are straight cut as pictured. Paired with high quality aftermarket ball bearings along with double lip axle seals. If your differential has tapered roller bearings, this will not fit. This kit should be installed by an experienced technician. Shims are included as the gears will need to be set up in your cases. Note: the O rings are not included, this is a cost savings measure as they are generally reusable. This kit will only fit six mounting hole differentials. Measure your outer diameter of the pinion seal, it should measure 2 3/4" (70mm) Measure your outer diameter of your axle seals! They should measure close to 2 1/16″ (52mm) To further verify fitment you can measure your pinion pilot shaft, this should be 5/8″ (16mm) Please take the time to measure your parts before buying this will save time and restocking fees. Fits 2015 and newer G2 style ATV 500/570/650/800/850/1000/1000R NON-XMR style REAR differential. 570/650 XMR machines do not have the true XMR differential.
Our Custom USA Made Maverick Swap Kit. Allows you to run the better/stronger OEM Maverick Differential in your Commander. Kit includes: Custom Black Powder coated Brackets All Hardware needed New OEM Maverick differential New OEM Driveshaft with correct yoke and seal protector installed. No welding needed BUT you will need to cut/drill part of your frame to make this fit. Stock axles will work, no stretched arms or lift needed. The maverick differential is considerably more quiet than the stock Commander unit. Maverick differentials have proven to hold up much better, often referred to Can-am’s first real SXS rear differential. The gear ratio is the same as your stock Commander differential. Will not fit in commanders with un locking differentials Maverick Differential Swap Instructions
Can-Am Rear Transmission Seal. Fits Large Gear Boxes, Standard and Low Ratio. Brand New OEM Seal OUTPUT SHAFT SEAL found on rear of gearbox, just in front of the rear driveshaft. This is the seal that goes on the rear, where the rear driveshaft goes out to the rear differential. If you are unsure if this is correct, please measure your current seal. If you get close to these specs it should work, the other option is much smaller in outer diameter. 72mm outer diameter 35mm inner diameter Current part number: 420831955 420831956
SHIPS FREE TO THE LOWER 48 STATES New OEM XMR Rear Differential Gear set, 10/36 Ring and Pinion gear set, Timken, Dichtomatik or SKF seals, NTN or IKO pilot bearing , OEM shim kit and OEM bearings Fits the larger style 800/850/1000/1000R XMR style REAR differential first seen on the 2013 Outlander 1000 XMR. This gear set will not install into 650 xmr and 570 xmr differential cases. Please see our other listings for those. This is a common part to swap on to generation 2 atvs. We do sell complete kits to do so, please check out our other listings. Part number 703500870
NEW AFTERMARKET STARTER VTWIN Will come as pictured Part Numbers: 420684560 420684562 420684568 420684566
Brand New Genuine OEM XPS Full Synthetic Oil Change Kit. Ultra convenient “all in one” kit saves time and money. For Can-am off road vehicles with 500cc or larger Rotax engines. Excludes Traxter and Quest. Not compatible with Maverick X3 Includes 2 quarts plus 1 16 fl oz of 4T synthetic oil 0W40, 0-rings, rotax oil filter, and copper washer for old style and new style drain plugs. May not ship in original box Part Number: 779259
This Product replaces the stock snorkel Mohawk prefilter screen. This prevents any mud clogging up and still allows air to flow into the snorkels. Made in USA Replaces OEM 705010922 to be installed in OEM Mohawk riser 705009685
2012-2018 G2 ATV Rear Differential Swap Kit Kit includes: Rear Differential, Rear driveshaft, Bolt and Washer. This kit includes a rear differential with: Tapered roller bearings Three bearings on the pinion gear 6 inch diameter ring gear Your choice of gear style, spiral bevel or straight cut. Both have the same 3.60 ratio as your current differential. Spiral Bevel Gears are sourced from the 2013-18 800 850 and 1000 XMR differentials. Current part number 705502546 Old part numbers: 705502178 & 705502090 Straight Cut gears are sourced from the 2019+ 650+ differentials. Current part number 705502808 The driveshaft included is an OEM shaft with the correct end yokes for your application. The differential end yoke will not use a wear ring, this has been done away with by BRP the yoke is what the pinion seal touches now. You will need to fill the differential with 250ml (8.4oz) of 75W-140 gear oil and transfer over your fill plug and washer. The torque spec on the driveshaft retaining bolt is 55ftlbs with thread locker applied. Some minor trimming on the brackets that surround the differential is required. These differentials have the provision for an ABS sensor, this is standard on euro models, for mud riders state side, you can fill this hole with RTV or leave it open. If you are running the silver protector ring on your axle, you will need to push the ring outward slightly. We choose to remove these dust covers as they tend to trap debris when run under water.
NEW OEM BRP Steering Stem Bushing Half This is sold as one (1) half. Fits G2 2012+ ATV Renegade/Outlander OEM part number: 709400783
NEW Genuine Can-am Rear Prop Shaft for 2012-18 Outlander Or Renegade 500, 570L, 570, 650, 800R or 850.
Be sure to check part numbers before ordering if you have a 1000.
This will work on 2015+ Outlander 1000 non XMR/T3 machines (small gearbox).This updated shaft does not need wear ring as it is simply machined larger in outer diameter.
Current Part number: 703500986
Previous Part numbers: 703500925 703500855 70550140618 spline gearbox side yoke
18 spline differential side yoke
High quality aftermarket Timken or SKF axle oil seal. Fits ATV rear differentials 2015-current, some UTV’s To be 100% sure on fitment, measure your outer diameter on your seal, it should read 52mm This seal has a 30mm inner diameter 52mm outer diamter and is 8mm thick. Replaces OEM 705501556 Order qty two per machine.
SHIPS FREE TO THE LOWER 48 STATES Standard G2 Rear Differential Bearing and Seal Kit High quality aftermarket bearings along with double lip axle seals. Bearing and Seal Brands include: Nachi, KOYO, NTN, Timken, SKF The large case sealing and pinion gear O-rings are NOT included as a cost saving measure, these O-rings are reusable if not damaged. There are a few options for kits, please verify your differential uses this style of gears before ordering! This will only fit six mounting hole differentials. Open up the differential! Check for two bearings total (one on each side) on the ring gear. If you only have two proceed to the next measurement. Measure your outer diameter of your axle seals! They should measure close to 2 1/16″ (52mm) To further verify fitment you can measure your pinion pilot shaft, this should be 5/8″ (16mm) The last pictures show this very clearly. Please take the time to measure your parts before buying this will save time and restocking fees. Fits 2015 and newer G2 style ATV 500/570/650/800/850/1000/1000R NON-XMR style REAR differential.570/650 XMR machines do not have the true XMR differential.
NEW OEM Shock Bushing for base black body hydraulic type shocks. These will fit: 2020 and prior Commanders 800 800R 1000 1000R G1/G2 Outlanders 400 450 500 570 650 800HO 800R 850 1000 1000R Oem part number 715900122
SHIPS FREE TO THE LOWER 48 STATES
Late G1 Early G2 Standard Rear Differential Rebuild Kit
There are a few options for rebuild kits, please measure your parts before ordering!!
OEM Rear Differential Gear set 10/36 Ring and Pinion gear set. The gears are straight cut as pictured.
Paired with high quality aftermarket bearings along with double lip axle seals.
This kit should be installed by an experienced technician. Ring gear shims are included as the gears will need to be set up in your cases, the pinion shims should remain unchanged
Note: the O rings are not included, this is a cost savings measure as they are generally reusable.
There are a few options for kits, please verify your differential uses this style of gears before ordering! This will only fit six mounting hole differentials.
Open up the differential! Check for two bearings total (one on each side) on the ring gear. If you only have two proceed to the next measurement.
Measure your outer diameter of your axle seals!
They should measure close to 1 3/4" (47mm)
To further verify fitment you can measure your pinion pilot shaft, this should be 9/16? (14mm)
The last pictures show this very clearly. Please take the time to measure your parts before buying this will save time and restocking fees.
High quality Timken oil seal. Replace a leaking front output seal on your canam. This is the seal that seals the engine through shaft coming out of the front of your Vtwin engine below the front exhaust header. To be 100% sure on fitment, measure your outer diameter on your seal, it should read 47mm This seal has a 25mm inner diameter 47mm outer diamter and is 7mm thick. Replaces OEM part numbers: 420430588 420430589 420430580
New NGK Spark Plug 93444
OEM part number 715900352
NGK part number LMAR8D-J
These spark plugs work in 2015+ Outlander/Renegade 450 850 and 1000R also fits Defender HD5
Shell
Thread Diameter: 10mm
Thread Pitch: 1.0mm
Seat Type: Gasket
Reach: 26.5mm (1.04″)
Hex Size: 9/16″ (14mm)
Terminal Type: Solid
Gap: .031″ (0.8mm)Center Electrode
Material: Nickel
Type: Standard
Size: 2.5mm
Projection: ProjectedGround Electrode
Material: Nickel
Type: Multi-GroundSpecifications
Resistor: Yes
Resistor Value: 5k Ohm
Heat Range: 8
Torque Specs: Aluminum: 7.2-8.7 lb. ft.
NEW OEM Screw Part number 235381646 M8x16
New Genuine OEM Works on 2016+ Defender and Defender Max Works on both driver and passenger doors Part number 710004979 replaces 705800048
New Can Am Maverick Rear Differential Pinion Seal This is a New Genuine OEM seal Part number 705501933 New updated part number 705502276 Press fit into differential, then seals against wear ring (if your driveshaft requires one) If your wear ring is grooved you should replace it.
Brand New OEM Stator Cover Gasket for V-Twin Engines. Fits 2006-Current V twin’s Part number 420651201
New OEM Differential Pinion Seal. Please check your wear ring, if that is grooved it is time to replace. Very easy to miss that and blame a new seal on a bad wear ring. Will fit: Gen 1 Front and Rear Diffs Gen 2 Outlander and Renegade Front and Rear Early Commander Rear All Maverick and Commander Front WILL NOT FIT G2 XMR 800/850/1000 REAR DIFFERENTIAL Measurements are shown: 70mm outside and 37mm inside Part number 705401481
Fully machined 20 spline yoke To be used with 398 U joint on rear driveshafts No wear ring required, this is simply machined to the size of the wear ring This yoke slides into the rear differential. OEM part number 715900499
Have Questions?
Our staff is available to answer questions
canampartsguy@gmail.com
1340 Okray Ave.
Plover, WI 54467
jared@canampartsguy.com
Cant find What you're looking for?
Visit our 
store!
2016 Can Am Parts, LLC. All rights reserved.