Used ECM (computer) with OEM Digital Key.
This pair is tested, cleared of any codes and run on our shop ATV before leaving.
Your Dash (speedometer) may need to be paired with BUDS. If you want to start and run the machine simply unplug the dash before installing the ecu. We provide the pairing service free of charge with purchase of ECU or Dash, contact us for further details.
Only fits Generation 1 bikes Outlander and Renegade 800 HO 2006 2007 2008
Part Number: 420266374 420266623 710000817
- Air Pressure sensor, this goes in the Black plastic Intake manifold. Will work on any 2006 to current Can am Outlander, Renegade, Commander, Maverick, Defender 500 570 650 800 850 1000 XT XMR MAX or XXC The Manifold Absolute Pressure sensor or MAP sensor is a sensor that is attached to the intake manifold. The MAP sensor responds to changes in the intake manifold pressure (vacuum) and provides a reading of engine load. How it works is 5 volts DC is supplied to the sensor from the ECU. Inside the MAP sensor there is a resistor that moves in relation to intake manifold pressure. The resistor varies the voltage between about 1V to 4.5V (depending on engine load) and that voltage signal is returned to the PCM to indicate manifold pressure (vacuum). This signal is essential for the PCM to determine fuel delivery. Part numbers: 420874650 707000564 707000995 0 261 230 030 ALFA ROMEO 46553045 ALFA ROMEO 46533518 CHERY S21-3614021 FIAT 46553045 FIAT 77364869 FIAT 7084986 FIAT 0000046553045 FIAT 46533518 LANCIA 46533518 LANCIA 0000046553045 LANCIA 46553045 MOOSE 2120-0994 PROTON PW810694 ROTAX (BOMBARDIER-ROTAX GMBH) 874 650 SCANIA 5166434
- OUT OF STOCK
Sliding Sheave for CVTech Canam Clutches
Part Number 0910-0006
- NEW OEM GEARBOX 570s come with a lower ratio gearbox than the normal low ratio gearboxes found in the 650’s and 500’s The extra low ratio gearbox will help bottom end power and with larger tires, this is the lowest ratio small gearbox. Current Part Number 420686569 Replaces: 420686567 420686560 420686561 This is found in Outlander or Renegade 570 DPS XT or XMR Will work in 650,800,850, and 2015 and newer 1000/1000R ATV’s Teeth count and gear ratio Ring & Pinion 38/28 = 1.357 High Gear set 46/20 = 2.300 Low Gear set 31/14 = 2.214 High final ratio 3.341:1 Low final ratio 5.662:1 2015 and newer non XMR outlander 1000’s have this style gearbox, if you have fitment questions, please contact us! If you are installing this on an early G1 ATV you will need to transfer over your gear position sensors.
- SHIPS FREE TO THE LOWER 48 STATES New OEM Standard G2 Rear Differential Ring & Pinion Gear Set 1652 There are a few options for kits, please verify your differential uses this style of gears before ordering! This will only fit six mounting hole differentials. OEM Rear Differential Gear set 10/36 Ring and Pinion gear set. The gears are straight cut as pictured. Open up the differential! Check for two bearings total (one on each side) on the ring gear. If you only have two proceed to the next measurement. Measure your outer diameter of your axle seals! They should measure close to 2 1/16? (52mm) To further verify fitment you can measure your pinion pilot shaft, this should be 5/8? (16mm) Please take the time to measure your parts before buying this will save time and restocking fees. Fits 2015 -2019 G2 style ATV 500/570/650/800/850/1000/1000R NON-XMR style REAR differential. 570/650 XMR machines do not have the true XMR differential.
- OUT OF STOCKNew Demon Heavy Duty Axle Rear Left Fits: 2006-2018 ATV Outlander/Renegade 500 570 650 800HO 800R 850 1000 1000R Part number PAXL-1130HD Replaces OEM 705500867 705500979 705501483 705502472 705501485 Through years of research and development Demon Powersports has developed an axle that doesn’t burn a hole in your pocket and adheres to the highest quality standards. These axles are bigger, beefier, and stronger. Demon Heavy Duty Axles are built using larger CV joints and shafts, paired with our proprietary dual heat treatment process, and 4340 Chromoly Steel inner CV cage gives these the axles the edge it needs for superior strength and longevity. These axles also utilize a unique double plunge design which allows it to achieve higher articulation angles approximately, the axles are designed to slide on the bar splines allowing for 1.5 inches of travel and 40° articulation over terrain on the inboard joint. The outboard joint can travel 0.5inches and swing from 45°-47° depending on the model. The Demon heavy duty axles are equipped The TPEE (Thermoplastic polyester elastomer) boots which are stronger, stiffer, more fatigue resistant, puncture resistant, and more temperature resistant than a standard OEM boot. Axles use molybdenum grease to provide low friction and smooth motion. Trust in Demon Heavy Duty Axles to keep you riding!! • 15%-20% increase in diameter compared to regular axle • Inner cage made up of 4340 chromoly steel • Dual heat treated high strength chromoly steel shaft • Thermoplastic polyester elastomer (TPEE) Boot • 10%-15% increase in CV joint size compared to regular joints • Wider articulation angles • Dual plunge design prevents axle from binding • Packed with high load molybdenum grease Precision CNC machined • Can Fit 1.5”- 5” Bracket lift of particular brands/ All Portal Gear Lifts / 1.5”- 5” A-arms of particular brands • 1-year ltd warranty