CVTech Primary Clutch Holding tool. Very nice tool for torquing nut on the clutch or the bolt holding clutch on to the crankshaft taper. 0155-1018 Part number
NEW OEM BRP XPS DCT fluid 9779710 one quart 32oz dual clutch transmission synthetic oilThe best protection for the most demanding conditions, from low-end torque to high horsepower.Our most advanced formulation delivers even more peace of mind with superior performance and protection, thanks to increased shear resistance & detergency without compromising on volatility.SpecificationsExceptional oxidation stability and resistance to chemical deterioration — maintains long-lasting fluid quality and helps prolong transmission lifeExcellent lubricating characteristics for clutch friction durability, smooth shifting, and excellent wear protectionExcellent viscosity stability to help assure adequate lubrication and to maintain excellent viscosity properties at low start-up temperatures and high operating temperaturesDependable protection against rust and corrosionExcellent seal performance to protect against fluid leakage and prevent component failures from oil starvationFormulated especially for your side by side vehicle
Please verify your differential uses this style of Seals before ordering! Can Am Standard Rear Differential Pinion and Axle Seals (Timken or SKF) Please measure your parts before ordering to verify fitment. The Pinion Seal has a 70mm Outer Diameter and the standard 37mm inner diameter. Replaces part number 705401481 The Axle Seal has a 52mm Outer Diameter And the standard 30mm inner diameter. Complete Seal kit for Standard Rear differentials common to find in 2016 and newer ATVs or if your differential has been repalced.
New short wiring harness for rear tail lights Will need to be wired in to work. This plugs in to Tail light part number 710001645 Fits: G2 ATV's with dual tail lights, Commanders, and Mavericks (non X3/Sport/Trail)
HD Clutch bolt set for most every Can-am V-twin 2006 to current. Will not work on: Maverick Turbo Maverick X3 Maverick Sport Maverick Trail Defender These will swap out the factory Torque To Yield (TTY) bolts/studs. M10 and M12 Black-Oxide Alloy Steel Socket Head Bolt These are class 12.9 bolts, with a tensile strength of 170,000 psi, these alloy steel bolts are stronger than Grade 8 steel bolts. 8 and 10mm Allen Sockets required to install these bolts. 18-8 Stainless Steel Single-Wave Washers included, these help prevent loosening, use with your existing washers. Installation Torque Specs: 80 ft·lb On the Primary Bolt 45 ft·lb On the Secondary Bolt (red thread locker recommended, allow to set up overnight)
NEW MRRPM Upper Motor Mount for installing 'big block" 1000 engines into a G1 chassis Steel, black in color
Replaces OEM part number 420222691 Upgrade your plastic thermostat housings/water neck on your vtwin 500/570/650/800/850/1000 SOLD AS PAIR These will work in Commanders, Mavericks, Outlanders & Renegades
Used- Good Condition OEM Can-Am Grab Handle for Commander & Maverick Product Number: 705203332 Comes as Pictured- OUT OF STOCK
NEW OEM G2 ATV Battery Hold Down Fixation Plate Kit. This retains the battery in place, and gives your seat something to latch into Kit includes: Fixation Plate 710009129 replaces 710002404 Positive Battery Terminal Cover 710006729 Rubber Stopper 705014429 Three aftermarket stainless bolts 
New All Balls Racing Engine Air Filter Part number 48-1012 10 inches tall 5 inch diameter Replaces OEM 715900394 Fits 2016-Current Defenders HD5, HD8, and HD10's both 3 and 6 seat machines Fits 2018-Current Maverick Trail 800 and 1000 Fits 2019-Current Maverick Sport 1000
Can Am Outlander Renegade Front U Joint These are found on the front prop shaft of G1 ATV’s and front drive shaft of Commander and Maverick (non X3/Sport/Trail) Also used on the 400 rear drive shaft 22mm caps. This is a new OEM part Replaces Part numbers: 703000023 703500814 703500607 703500135 703500002 703000024 715900183 715900325
20 Spline Yoke Fits: XMR 1000, Maverick and ’14 & newer Commander style Rear differentials. You will need a wear ring if you are using this on the differential side of the shaft. These yokes are made to very tight tolerances, if you are not careful when installing these you can damage the yoke or your pinion shaft. We recommend you take your time and clean the pinion gear before installing. —Great for custom applications— Uses Factory size U joint (398 at the auto parts store) Part numbers 715900271
OEM Air Filter for Gen 1 Outlander and Renegades. Fits 500, 650, and NON-R 800 engines, from 2006 - 2012. Comes as Pictured.
NEW Chrome Conical Taper M10 Lug Nut Set of 16 M10x1.25 thread size 60 Degree taper 14mm Hex head size, great for use with aftermarket wheels where socket space is a concern These will work on every Canam ATV since 2006 and most every Canam sxs Will not fit the Maverick X3 12mm wheel studs. Part numbers: 57-94121, ALUG14BX
One spark plug boot, this is used on many applications 2020 and older, if you are unsure on fitment, please contact us.
Part number 420265248
Replaces 710000041 and 420265240
Can-Am Rear Transmission Seal. Fits Large Gear Boxes, Standard and Low Ratio. Brand New OEM Seal OUTPUT SHAFT SEAL found on rear of gearbox, just in front of the rear driveshaft. This is the seal that goes on the rear, where the rear driveshaft goes out to the rear differential. If you are unsure if this is correct, please measure your current seal. If you get close to these specs it should work, the other option is much smaller in outer diameter. 72mm outer diameter 35mm inner diameter Current part number: 420831955 420831956
EPI Lower Ball Joint Fits: G1 Outlanders 400 500 650 800 Replaces OEM: 706200444 This style of ball joint bolts to the lower control arm. If you are unsure of fitment, please ask! 2006 - 2014 Can-Am Outlander 400 2007 - 2012 Can-Am Outlander 500 2008 - 2012 Can-Am Outlander 650 2006 - 2011 Can-Am Outlander 800 2006 - 2013 Can-Am Outlander Max 400 2007 - 2013 Can-Am Outlander Max 500 2007 - 2012 Can-Am Outlander Max 650 2006 - 2012 Can-Am Outlander Max 800
New OEM Secondary Clutch Outer Bearing
Current Part Number 420932421
Replaces 420932426 and 711932426
52mm Outer Diameter
25mm Inner Diameter
15mm Thick
New OEM Gasket Will fit the following 2016-2019 Defender HD8 and HD10 2018-2019 Maverick Trail 800R and 1000R 2019 Maverick Sport 1000R
Can-am Oem Primary Clutch Bolt M14X1.5X153.5 2015-2017 Maverick 1000R TURBO This is the larger style primary bolt found on turbo 1000R Vtwin Maverick applications. 420841092 420841091
New Genuine OEM Handlebar Wind Deflector. Part number 715006117
New Genuine OEM Mounting kit sold separately Part number 715000537
Part number 0950-1011
This isolates the spring from the one way bearing on a trail bloc primary clutch.
Measurements as shown
Vertex water pump rebuild kit
Will fit all V-Twin Can-Am Engines
Part Number 680-1957 821957
Replaces OEM 420650370 420651190 420230415 420650310 420650315
Have Questions?
Our staff is available to answer questions
canampartsguy@gmail.com
1340 Okray Ave.
Plover, WI 54467
jared@canampartsguy.com
Cant find What you're looking for?
Visit our 
store!
2016 Can Am Parts, LLC. All rights reserved.