- New OEM Canam CVT Air Intake pre-filter Fits 2013+ Outlander G2 with the round CVT intake duct inlet. Part # 715003483 Adds extra protection to your engine in harsh riding conditions. Filter blocks particles larger than 0.007" (0.19 mm). Easy, tool-less installation. Necessary to maintain vehicle warranty when tracks are installed. Standard on Outlander 650 X mr, 850, 1000, 1000R engines & G2L PRO. Not compatible with Snorkel kits
- OUT OF STOCKNEW OEM G2 ATV Battery Hold Down Fixation Plate Kit. This retains the battery in place, and gives your seat something to latch into Kit includes: Fixation Plate 710009129 replaces 710002404 Positive Battery Terminal Cover 710006729 Rubber Stopper 705014429 Three aftermarket stainless bolts
- OUT OF STOCKSHIPS FREE TO THE LOWER 48 STATES New Forged OEM Can-am piston kit with rings. Matched to an OEM Rotax used Cylinder. This is ready to install on your 650 Outlander engine. Two are required per engine. Piston comes with rings installed. Piston pin, and clips are not included. Part number 420684111 420613888
- OUT OF STOCKNEW OEM Can-Am Maverick X3 Right Sway Bar End Link (Also called RH Ball Joint) Fits RIGHT Front on Can-Am Maverick X3 and X3 MAX's Part Number: 706202765
- Can Am Commander 800 1000 Dual CVT Air Intake 2011 2012 2013 2014 2015. Complete kit to upgrade CVT cover from 1 inlet - 1 outlet to 2 inlets - 2 outlets. Keeps CVT system cooler in extreme use conditions. Reduction in belts temps range from 40 to 70 degrees! Used in conjunction with Snorkel Kit to get maximum airflow to CVT while under extreme conditions. Needed to install Snorkel Kit (715001728) on Commander. Part Number: 715002467.
- OUT OF STOCKNew Genuine OEM Convex mirror for wide angle visibility Can be used with or without roof and windshields 2013-2018 Maverick 2011-2020 Commander Part number 715000956 Install with in minutes
- New Genuine OEM Robust injected-polypropylene construction allows for the right fit and easy installation Adjustable unit safely holds smartphones or small tablets with a length or width measuring between 2.9" (7.5 cm) and 5.1" (13.0 cm) with or without protective case Integrated storage 0.6 Gal Guiding wire grooves to pass charging cable through the lid Possibility of relocating 12V power outlet or installing USB outlet in storage compartment Not compatible with windshields and Snorkel Kit
NEW OEM CVT cover with heat shield installed from factory Fits: Maverick 1000R two seat 2013-2014 Commander 1000 MAX four seat 2014-2016 Commander 800R MAX four seat 2017-2019 ONE Breather hole in front of Primary clutch. This is the cover with the most room. Common to use this on newer V-twin 1000R Mavericks with aftermarket clutches that do not require the extra breathers. Inner cover 420611407 Outer cover 420212318 13 Hex head CVT housing bolts 420440568 Gasket 420430126 O-rings – 420430407 and 420631087 Hex Bolts – 420440207 Also has a nut and washer – 232561434, 224061121 Nylon drain plug and clamp
Fitment: DCP30 Can-Am Drive clutch governor cup puller
Replaces DPC25OEM 529036350
2015-18 Maverick 1000R Turbo
2017+ Maverick X3 Turbo (including P drive)
2018+ Defender HD8 HD10
2018+ Maverick Trail 800R 1000 1000R
2019+ Maverick Sport 800R 1000 1000R
2020+ Commander 800R 1000RAides in safe disassembly of the drive clutch for servicing.
Use with Gboost drive clutch puller # TOOL31SDGBOOST Instructional Video CLICK HERE
Features:
All GBoost® pullers start out with annealed, cold-rolled alloy steel.
Oil Quenched
Tempered
Rockwell hardness between 50-55
Zinc plated to prevent rust and thread deterioration
Machined to exact specifications in the U.S.A.
This results in31% higher tensile strength
19% higher yield strength
Stronger than any existing OEM pullers- New aftermarket switch replaces OEM part numbers: 710008837 710005070 710000791 710004618 703500920 710003062 710002883 710003039 710004041 Fits on: 2006-2019 Outlander and Renegades 500 650 800HO 800R 850 1000 1000R 2020 Outlander 650 STD DPS XT XMR 2020 Outlander 6x6 650 or 1000 2020 Renegade 570 XMR Will not work on 400’s or machines with drive by wire. 3 position headlight switch OFF/Low/High beam Will come as pictured Please look at the plug style on your current switch. The buttons may be arranged differently than the switch you are replacing. We have found this switch will work on DPS or non DPS equipped machines