Shop

  • New Oem Canam Pinion nut, this is spun on to the pinion gear to retain the bearings on the pinion gear of xmr differentials on ATV XMR's G2 800/850/1000/1000R This is not needed on 570 or 650 XMR models The threads are M28x1.25 Right Hand the outer diameter is 51mm Please check that this is the correct nut for your application Part number 705501550
  • This is the XMR 1000 rear differential found in 2013-2018 800R 850 1000/1000R XMR.

    It will fit g2 bikes (500/650/800/850/1000) if you are upgrading you will need to shorten your shaft 1.75? or buy a kit from us, please see our other listings.

    This differential has automotive style cut gears, tapered roller bearings, along with an overall larger gear size. There are a total of three bearings on the pinion gear giving it much more support over the standard rear differentials, this requires a shorter driveshaft, as mentioned earlier if you are swapping this in place of a standard differential.

    Pinion spline count 20, standard differentials use 18 spline pinion shafts, that are smaller in diameter. If you are upgrading you will need a 20 spline end yoke to match.

    In every way this is a beefier differential.

    To bolt your driveshaft on this differential you will need a M10x1.25 16mm long bolt (not included)

    Current part number 705503535
    Old part number 705502546 705502178,  705502090

  • OUT OF STOCK
    Can-am Shim Kit for XMR G2 800 or larger 2012-current Rear Differentials. Part number 703500835
  • Providing protection from freezing or overheating, our Universal Pre-Mixed Coolant is easy to use as it contains the correct dilution and necessary additives your engine needs. Not only does coolant provide heat balance for your engine, but it’s also designed to prevent corrosion and rust and to inhibit cavitation in powershot cooling systems.

    This XPS Universal Pre-Mixed Coolant is the product to use for vehicles that normally use a 2-year antifreeze/coolant (green).

    Part number 9779149

    Sold by the quart

  • Brand New Genuine OEM XPS Full Synthetic Oil Change Kit.

    Ultra convenient “all in one” kit saves time and money.

    For Can-am off road vehicles with 500cc or larger Rotax engines. Excludes Traxter and Quest.

    Not compatible with Maverick X3

    Includes 2 quarts plus 1 16 fl oz of 4T synthetic oil 5W40, 0-rings, rotax oil filter, and copper washer for old style and new style drain plugs.

    May not ship in original box

    Part Number: 779258 replaced by 9779488

  • Can Am OEM Upper ball joint NEW OLD STOCK Part number is 706201394
  • New OEM Tail light assembly, with bulb, plug in and go! Fits late G1 and all G2L Outlander models. Part # 710001203
  • Aftermarket G2 ATV Caliper piston set, each kit contains two pistons to rebuild one caliper.

    Precision machined from high grade 304 Stainless Steel.

    These fit G2 ATV brake calipers, if you have fitment questions please reach out, we are here to help.

  • NEW Prop Shaft Low profile pair of clamps for 715900118 boot. Clamps also work for G2 front shaft boot 705401093. The last few pictures show the clamps loose, then installed nice and tight. Sold in pairs enough to do one boot.
  • OUT OF STOCK
    NEW Quad Logic Brand G2 ATV Can Am Airbox Seal  Part number 500-1139-PU This is an improved design over factory Apply a small amount of grease to aid install, this is much thicker and denser than the OEM o-ring or gasket Replaces OEM part numbers: 293300165 293300175 293300179
  • NEW Speed Sensor Quad Logic brand Will fit 2006-Current Outlander, Renegade, Maverick, Maverick X3, Commander, and Defenders 2210-0568 500-1024 Replaces OE Numbers 420265621, 420265622, 420265624, 420265625, 420265626, 420265629, 707000745 and 711265622 
  • Moose Racing Radiator Cap Fits Outlander, Renegade, Commander, Defender and Maverick Unsure on fitment, please ask us. Cap is set to the same 15.9PSI as stock. If you current cap is not holding pressure replacing with new will help avoid overheating. Replaces OEM 709200207 709200033