Can-Am Rear Transmission Seal. Fits Large Gear Boxes, Standard and Low Ratio. Brand New OEM Seal OUTPUT SHAFT SEAL found on rear of gearbox, just in front of the rear driveshaft. This is the seal that goes on the rear, where the rear driveshaft goes out to the rear differential. If you are unsure if this is correct, please measure your current seal. If you get close to these specs it should work, the other option is much smaller in outer diameter. 72mm outer diameter 35mm inner diameter Current part number: 420831955 420831956
One spark plug boot, this is used on many applications 2020 and older, if you are unsure on fitment, please contact us.
Part number 420265248
Replaces 710000041 and 420265240
NEW Chrome Conical Taper M10 Lug Nut Set of 16 M10x1.25 thread size 60 Degree taper 14mm Hex head size, great for use with aftermarket wheels where socket space is a concern These will work on every Canam ATV since 2006 and most every Canam sxs Will not fit the Maverick X3 12mm wheel studs. Part numbers: 57-94121, ALUG14BX
OEM Air Filter for Gen 1 Outlander and Renegades. Fits 500, 650, and NON-R 800 engines, from 2006 - 2012. Comes as Pictured.
20 Spline Yoke Fits: XMR 1000, Maverick and ’14 & newer Commander style Rear differentials. You will need a wear ring if you are using this on the differential side of the shaft. These yokes are made to very tight tolerances, if you are not careful when installing these you can damage the yoke or your pinion shaft. We recommend you take your time and clean the pinion gear before installing. —Great for custom applications— Uses Factory size U joint (398 at the auto parts store) Part numbers 715900271
Can Am Outlander Renegade Front U Joint These are found on the front prop shaft of G1 ATV’s and front drive shaft of Commander and Maverick (non X3/Sport/Trail) Also used on the 400 rear drive shaft 22mm caps. This is a new OEM part Replaces Part numbers: 703000023 703500814 703500607 703500135 703500002 703000024 715900183 715900325
New All Balls Racing Engine Air Filter Part number 48-1012 10 inches tall 5 inch diameter Replaces OEM 715900394 Fits 2016-Current Defenders HD5, HD8, and HD10's both 3 and 6 seat machines Fits 2018-Current Maverick Trail 800 and 1000 Fits 2019-Current Maverick Sport 1000- OUT OF STOCK
NEW OEM G2 ATV Battery Hold Down Fixation Plate Kit. This retains the battery in place, and gives your seat something to latch into Kit includes: Fixation Plate 710009129 replaces 710002404 Positive Battery Terminal Cover 710006729 Rubber Stopper 705014429 Three aftermarket stainless bolts 
Used- Good Condition OEM Can-Am Grab Handle for Commander & Maverick Product Number: 705203332 Comes as Pictured
Replaces OEM part number 420222691 Upgrade your plastic thermostat housings/water neck on your vtwin 500/570/650/800/850/1000 SOLD AS PAIR These will work in Commanders, Mavericks, Outlanders & Renegades
NEW MRRPM Upper Motor Mount for installing 'big block" 1000 engines into a G1 chassis Steel, black in color
HD Clutch bolt set for most every Can-am V-twin 2006 to current. Will not work on: Maverick Turbo Maverick X3 Maverick Sport Maverick Trail Defender These will swap out the factory Torque To Yield (TTY) bolts/studs. M10 and M12 Black-Oxide Alloy Steel Socket Head Bolt These are class 12.9 bolts, with a tensile strength of 170,000 psi, these alloy steel bolts are stronger than Grade 8 steel bolts. 8 and 10mm Allen Sockets required to install these bolts. 18-8 Stainless Steel Single-Wave Washers included, these help prevent loosening, use with your existing washers. Installation Torque Specs: 80 ft·lb On the Primary Bolt 45 ft·lb On the Secondary Bolt (red thread locker recommended, allow to set up overnight)
Have Questions?
Our staff is available to answer questions
canampartsguy@gmail.com
1340 Okray Ave.
Plover, WI 54467
jared@canampartsguy.com
Cant find What you're looking for?
Visit our 
store!
2016 Can Am Parts, LLC. All rights reserved.