Shop

  • Can-am Maverick Rear differential shim kit. Needed when changing gears in your maverick rear differential. Part Number: 703500839
  • Differential Vent Tube 8mm diameter Part number 705501584
  • Gearbox Shift Shaft Seal 28mm OD 12mm ID 7mm Thick Part numbers: 711250450 420250450
  • Brand new aftermarket secondary clutch assembly This is found on many BRP ATVs. Please ask if you have fitment questions. Replaces OEM Part Part Numbers: 420280173 420280176 420280178 420932421 420280236 420280499 420245910 420245911 420220913 Installation Torque Specs: 45 ft·lb On the Secondary Bolt (red thread locker recommended, allow to set up overnight)
  • New OEM Canam CVT Air Intake pre-filter Fits 2013+ Outlander G2 with the round CVT intake duct inlet. Part # 715003483 Adds extra protection to your engine in harsh riding conditions. Filter blocks particles larger than 0.007" (0.19 mm). Easy, tool-less installation. Necessary to maintain vehicle warranty when tracks are installed. Standard on Outlander 650 X mr, 850, 1000, 1000R engines & G2L PRO. Not compatible with Snorkel kits
  • New Genuine OEM steering stem for G2 Outlander and Renegade This will only fit NON power steering models Will not work on power steering bikes Current Part number 709401008
  • Left Side (Driver) Front One Caliper Set Part number: DP545 Replaces OEM # 705601149 Please contact us to confirm fitment if you are unsure. DP Brakes Brake Pads are designed with sintered metal compounds to give your SXS high-tech performance in all conditions Pads have a quick break-in period so you get maximum performance fast DP Brakes design and materials ensure consistent, hard stops and fade-free performance Sintered metal compounds outlast more conventional organic or aramid fiber pads
  • Right Side (Passenger) Front One Caliper Set Part number: DP544 Replaces OEM # 705601150 Please contact us to confirm fitment if you are unsure. DP Brakes Brake Pads are designed with sintered metal compounds to give your SXS high-tech performance in all conditions Pads have a quick break-in period so you get maximum performance fast DP Brakes design and materials ensure consistent, hard stops and fade-free performance Sintered metal compounds outlast more conventional organic or aramid fiber pads
  • MOOSE UTILITY Shifter Cable Part Number 0652-2426 Replaces OEM number 707001721 Heavy-duty stainless steel end fittings at both ends for corrosion resistance and longevity Roughly 145 inches long from end to end Fits four seat MAX models: 2017-2019 Defender HD10/HD8 MAX
  • New Demon Heavy Duty Axle Fits: 2011-2015 Commander 800R/1000 without the rare option of a un locking rear differential. Part number PAXL-1156HD Replaces OEM 705500960 705501456 705501481 705502359   Through years of research and development Demon Powersports has developed an axle that doesn’t burn a hole in your pocket and adheres to the highest quality standards. These axles are bigger, beefier, and stronger. Demon Heavy Duty Axles are built using larger CV joints and shafts, paired with our proprietary dual heat treatment process, and 4340 Chromoly Steel inner CV cage gives these the axles the edge it needs for superior strength and longevity. These axles also utilize a unique double plunge design which allows it to achieve higher articulation angles approximately, the axles are designed to slide on the bar splines allowing for 1.5 inches of travel and 40° articulation over terrain on the inboard joint. The outboard joint can travel 0.5inches and swing from 45°-47° depending on the model. The Demon heavy duty axles are equipped The TPEE (Thermoplastic polyester elastomer) boots which are stronger, stiffer, more fatigue resistant, puncture resistant, and more temperature resistant than a standard OEM boot. Axles use molybdenum grease to provide low friction and smooth motion. Trust in Demon Heavy Duty Axles to keep you riding!! • 15%-20% increase in diameter compared to regular axle • Inner cage made up of 4340 chromoly steel • Dual heat treated high strength chromoly steel shaft • Thermoplastic polyester elastomer (TPEE) Boot • 10%-15% increase in CV joint size compared to regular joints • Wider articulation angles • Dual plunge design prevents axle from binding • Packed with high load molybdenum grease Precision CNC machined • Can Fit 1.5”- 5” Bracket lift of particular brands/ All Portal Gear Lifts / 1.5”- 5” A-arms of particular brands • 1-year ltd warranty
  • New Genuine OEM Fan Current part number 709200566 Old part number 709200373, 709200375 Will fit 2011-Current Commander and Commander Max
  • Full rear mesh screen reduces windshield backdraft for added cabin comfort. Installs quick and easily on roll cage. White Can-Am logo at top, to help maintain clear view. Part Number 715002851