Brand NEW aftermarket primary clutch two way bearing with shims Current part number 22-51782 Includes new bearing and two washers This two way bearing service kit includes everything you need to replace the two way bearing on the primary clutch. The thrust washers install on either side of the two way bearing. Replacing this bearing is a great place to start if you experience hard shifting, creeping while in gear or premature belt failure. This kit replaces the two way bearing, 42083235, 420233418 and both thrust washers 420427220 Will not fit mavericks with a rear driveshaft, if you have fitment questions please reach out, we are here to help.
New aftermarket 91mm bore piston and cylinder kit with gaskets rings wrist pins and circlips 10.5:1 compression ratio This is a ready to bolt on kit Fits: Commander 1000 ATV 1000/1000R Defender HD10 and DH9 Maverick Sport 1000 Please note this kit will not fit the SXS 1000R due to the lower compression ratio. No dowel pins included, you will need to transfer these from your engine Replaces OEM Part Numbers: 420685242 420685248 420623568 420623566 420630210 420245436 420216351 420685244 420296774
This is the NEW OEM factory gauge support from the G2L Outlander models 450 and 570
For use with Small LCD display
Part Number: 705007066
Set of four Moose gas shock kit for G1 Outlander 650/800 or Renegade 500/800 These shocks are the same length on all four corners, you may notice a slight lift, more so on a well used machine. *Please note these will not work in place of struts found on the Outlander 400/500 machines. Features: Moose gas shocks offer long term consistent performance over stock oil only damped shocks 10% stiffer springs provide a better ride and higher load capacity Works great on the front to better support your snowplow and on the rear when hauling cargo Smooth black color blends perfectly on your machine Direct bolt-on replacement: pre-installed spring allows for quicker setup P/N13102146X4
Kit includes one universal boot, one reusable cone tool, two stainless steel clamps, grease pack, and silicone cone lube and instructions Expandable universal CV boot, slides and expands over reusable cone tool for trail side CV boot replacement Lithium based molybdenum grease ensures good lubrication for long CV joint life XL version of the original EZ Trail boot designed to fit UTVs and large ATVs Material is expandable yet tough enough to be a permanent fix Two clamping diameters ensure a good fit on most vehicles Boot material stays flexible in extreme cold temperatures- OUT OF STOCK
Inline fuel controller, this unit takes the fuel signal and modifies it based on throttle position and RPM inputs. Part number FC25009, please contact us if you have fitment questions. You can use a pre built map table or build your own custom map. Software is compatible with Power Commander, so you can download Power Commander maps to the unit Plug-n-play fuel management device pre-programmed with make/model specific maps Fully adjustable computer compatibility for ultimate tuning and personalization Use OEM-style connectors and high-quality wiring harnesses No computer necessary to modify fuel management Small, lightweight, and easy to fit on your bike Integrated O² optimizer where applicable 
Slider Blocks for Trailbloc Primary clutches for CANAM ATVS This is a set of six, you will need to transfer over your weights. Part number 0930-3022
New Genuine OEM steering stem for G2 Outlander and Renegade This will only fit NON power steering models Will not work on power steering bikes Current Part number 709401008
New Can Am Outlander Renegade and Commander V-Twin EFI Speedo Speedometer Display Dash 2018-2020 Please understand 2017 and older models require a different dash, even if yours looks the same. This is the factory Gauge/Screen. The dash is designed to auto pair, but sometimes it will not auto pair and you will have to program them together with buds software. This can be done at your local dealer or you can send in your ecu, key(s), and DPS (power steering) to us for programming. Contact for more information. It will display 0 miles, please record your current miles for your records. Current Part number: 710005553
New Maverick rear differential pinion housing nut socket tool. This tool will remove the nut that screws into the aluminum housing. Applying heat to the nut/housing is recommended before using this tool. There is no warranty with this tool. The nut should be left hand threaded, meaning turning counterclockwise will tighten the nut where clockwise will loosen it. Half inch drive socket. It is recommended to only use hand tools with this. Diameter (Exterior) 2 7/8" Diameter (Interior) 2 1/2"- OUT OF STOCK
NEW OEM BRP Thermostat Current part number 709200406 replaces 709200383 This style is external from the cylinder head. If you are unsure on fitment please contact us. 
OMC trunk seal for G2 Outlander This is an improved design over factory, this is much thicker and denser foam than the OEM gasket WILL NOT FIT G2L (models with steel racks) Replaces OEM part numbers: 293250275 219704369 293200163- OUT OF STOCK
NEW Outsiders Mud Crew Airbox seal This is an improved design over factory Apply a small amount of grease to aid install, this is much thicker and denser than the OEM o-ring or gasket Replaces OEM part numbers: 293300165 293300175 293300179 
MOOSE RACING HARD-PARTS Replacement Tie-Rod Ends 0430-0717 WILL NOT WORK WITH OEM TIE RODS Fits G2 ATV 2012-2018 with upgraded 12mm tie rods kit part number 0430-0674 This kit includes a pair of 12mm LH and RH ends, enough to repair one side of your ATV.- OUT OF STOCK
All Balls complete fuel pump module, retaining nut and gasket This fits G1 Models: 2009-2015 EFI Outlander 400 2009-2012 Outlander or Renegade 500 2009-2012 Outlander 650 2009-2011 Outlander 800R 2012 Outlander 800R XMR 2012 Outlander 800R MAX 2009-2011 Renegade 800R Part number: 47-1049 24-71022 Replaces OEM numbers: 703500766 703500781 709000194 709000245 - OUT OF STOCK
NEW OEM Brake Line Fits 2012-17 Renegade 500 570 800R 1000 and 1000R Current part number 705601489 Replaces 705601123 705601060 This connects the front master cylinder to the front calipers. Brake lines on 2012+ and newer Can-am ATVs are known to be difficult to bleed, it is best to set some time aside to bleed it multiple times to get a firm lever. 
MOOSE UTILITY Shifter Cable Part Number 0652-2894 Replaces OEM number 707000775 Heavy-duty stainless steel end fittings at both ends for corrosion resistance and longevity Roughly 53 inches long from end to end Fits two seat models: 2011-15 Commander 800R/1000 2013-15 Maverick 1000R
Part number 0950-1011
This isolates the spring from the one way bearing on a trail bloc primary clutch.
Measurements as shown
OEM Can-am BRP wheel bearing for Maverick X3
Part number 293350151
Sold Each
Can-am Rear Driveshaft G2 2019+ G2 Renegade 1000R base, XXC or XMR All New All OEM Shaft OEM U-joints, with OEM gearbox seal protector installed. **Please note, this is the most updated shaft and does not require a wear ring on the differential side of the shaft. The last two pictures illustrate this.** 20 Spline Gearbox side yoke (fits large type gearboxes) 20 Spline Differential side yoke (fits fits 705502808/705502546 rear differential) Current Part number: 703500990 Previous Part number: 703500928 703500901
Updated Can-am Rear G2 Driveshaft Fits: 2019+ Outlander 1000R (excluding MAX and XMR) 2019+ Outlander 650/850 (excluding MAX) 2019+ Renegade 650/850 All new all OEM Shaft OEM U-joints. OEM protector ring installed Gearbox side yoke swapped to 18 spline Current Part number: 703500988 Previous Part number: 703500858 703500931 If you have a 2019+ 570 short wheel base single rider, this may be the correct shaft for your application, the parts fiche may not show the correct part number. You will need to measure the outer diameter of your rear differential's pinon seal, this shaft will only work with machines that have a 80mm pinion seal. If you measure 70mm you will need 703500986. 20 spline differential side yoke (fits 705502808/705502546 rear differential) 18 spline gearbox side yoke (small gearbox size) No wear ring needed, the deferential side yoke is machined to the outer diameter that a wear ring would be.
SHIPS FREE TO THE LOWER 48 STATES OEM BRP Heated Grips and Thumb kit.- LED dimmer facilitates reading temperature settings. 4 temperature settings with individual controls for thumb and grips. Returns to previous heat setting. One-touch shutdown. Compatible with Intelligent Throttle Control (ITC). Wiring Cable (710004567) is required for installation on G2 650 and G2L 570.
NEW OEM Mode Switch Menu/Trip Found on 2020+ Outlander 850 1000R Part number 710006717
Left Side (Drivers) Front One Caliper Set Part number: DP412 Replaces OEM # 715500335 Please contact us to confirm fitment if you are unsure. DP Brakes Brake Pads are designed with sintered metal compounds to give your SXS high-tech performance in all conditions Pads have a quick break-in period so you get maximum performance fast DP Brakes design and materials ensure consistent, hard stops and fade-free performance Sintered metal compounds outlast more conventional organic or aramid fiber pads
Have Questions?
Our staff is available to answer questions
canampartsguy@gmail.com
1340 Okray Ave.
Plover, WI 54467
jared@canampartsguy.com
Cant find What you're looking for?
Visit our 
store!
2016 Can Am Parts, LLC. All rights reserved.