- OUT OF STOCK
NEW OEM BRP Rotax Engine. 2016+ ATV 850 Vtwin 78 horsepower@ 7300 RPM, 94mm bore, 61.5mm stroke, 10.5:1 compression ratio. The 850 will have the larger valves when compared to the 800R, these were first seen in the 2013 1000R maverick engine, these are 36.5mm and 31mm respectively. This is new, not rebuilt. It will ship as pictured. No electronics included, you will need to transfer over your parts. Shipped with signature required. 
CVtech Slider Shoe HD set of three for stamped plate 0930-3002
NEW OEM Shim Kit for standard ring gears. Wide Range of shims, this will allow you to set up your pinion depth. 44mm Outer Diameter. 36mm Inner Diameter. This is a loose fit Fits Front Standard Differentials Part number 705502060- OUT OF STOCK
SHIPS FREE TO THE LOWER 48 STATES Rear Differential Rebuild Kit for 2013-2018 "OG" Maverick 1000R/Turbo Rear Differentials. Will not fit X3 Trail or Sport Mavericks. You will need to shim this to your cases like any other gear set. Factory BRP: gears, roller bearings, pinion seal, washer and shims. IKO needle bearing, SKF or Timken axle seals, aftermarket driveshaft bolt. Replaces oem 703500840 703500869 703500867 703500868 703500837 705502275 705501556 
NEW Spanner Wrench This is to remove and install the 705501550 nut on ATVs with the tapered roller bearing rear differentials. Also known as the XMR or 2019+ style rear diffs. Use a 20 spline yoke to retain the assembly in a vice and spin the nut off. The nut should be RH threaded
NEW Spanner Wrench This is to remove and install the nut on 703500867 pinion assembly. Use a 20 spline yoke to retain the assembly in a vice and spin the nut off. The nut should be RH threaded
NEW OEM BRP Primary Clutch
Part number 420686870
Maverick X3 P-Drive Pully. This is a great way to upgrade your 2021 and older Maverick X3
Your existing belt will work just fine, although installing a new belt at this time is a great idea! We can direct you if you need help finding the right one for your machine.
The P-drive is a smoother engaging, less clunky, faster responding clutch when compared to the 2021 and older models.
Your existing M14X165 bolt and washer will work just fine when installing this clutch.
MOOSE RACING HARD-PARTS Tie-Rod Upgrade Kit 0430-0673 Fits G1 ATV 2006-2012 Will not fit G2 800R 2012 models, if you have fitment questions please ask. Replaces oem numbers 709400485 709400487 709402303 709400486 This kit upgrades your 10mm factory tie rods to 12mm LH and RH threaded rod for on machine adjustments Sold as a pair
2013-2019 driveshaft for Outlander Max machines New Genuine OEM Old Part Numbers 703500863 703500926 Current Part Number 703500987 18 Spline end yokes. Perfect for machines with a small gearbox and a standard rear differential.
Brand NEW aftermarket primary clutch two way bearing with shims Current part number 22-51782 Includes new bearing and two washers This two way bearing service kit includes everything you need to replace the two way bearing on the primary clutch. The thrust washers install on either side of the two way bearing. Replacing this bearing is a great place to start if you experience hard shifting, creeping while in gear or premature belt failure. This kit replaces the two way bearing, 42083235, 420233418 and both thrust washers 420427220 Will not fit mavericks with a rear driveshaft, if you have fitment questions please reach out, we are here to help.
New aftermarket 91mm bore piston and cylinder kit with gaskets rings wrist pins and circlips 10.5:1 compression ratio This is a ready to bolt on kit Fits: Commander 1000 ATV 1000/1000R Defender HD10 and DH9 Maverick Sport 1000 Please note this kit will not fit the SXS 1000R due to the lower compression ratio. No dowel pins included, you will need to transfer these from your engine Replaces OEM Part Numbers: 420685242 420685248 420623568 420623566 420630210 420245436 420216351 420685244 420296774
This is the NEW OEM factory gauge support from the G2L Outlander models 450 and 570
For use with Small LCD display
Part Number: 705007066
Set of four Moose gas shock kit for G1 Outlander 650/800 or Renegade 500/800 These shocks are the same length on all four corners, you may notice a slight lift, more so on a well used machine. *Please note these will not work in place of struts found on the Outlander 400/500 machines. Features: Moose gas shocks offer long term consistent performance over stock oil only damped shocks 10% stiffer springs provide a better ride and higher load capacity Works great on the front to better support your snowplow and on the rear when hauling cargo Smooth black color blends perfectly on your machine Direct bolt-on replacement: pre-installed spring allows for quicker setup P/N13102146X4
Kit includes one universal boot, one reusable cone tool, two stainless steel clamps, grease pack, and silicone cone lube and instructions Expandable universal CV boot, slides and expands over reusable cone tool for trail side CV boot replacement Lithium based molybdenum grease ensures good lubrication for long CV joint life XL version of the original EZ Trail boot designed to fit UTVs and large ATVs Material is expandable yet tough enough to be a permanent fix Two clamping diameters ensure a good fit on most vehicles Boot material stays flexible in extreme cold temperatures- OUT OF STOCK
Inline fuel controller, this unit takes the fuel signal and modifies it based on throttle position and RPM inputs. Part number FC25009, please contact us if you have fitment questions. You can use a pre built map table or build your own custom map. Software is compatible with Power Commander, so you can download Power Commander maps to the unit Plug-n-play fuel management device pre-programmed with make/model specific maps Fully adjustable computer compatibility for ultimate tuning and personalization Use OEM-style connectors and high-quality wiring harnesses No computer necessary to modify fuel management Small, lightweight, and easy to fit on your bike Integrated O² optimizer where applicable 
Slider Blocks for Trailbloc Primary clutches for CANAM ATVS This is a set of six, you will need to transfer over your weights. Part number 0930-3022
New Genuine OEM steering stem for G2 Outlander and Renegade This will only fit NON power steering models Will not work on power steering bikes Current Part number 709401008
New Can Am Outlander Renegade and Commander V-Twin EFI Speedo Speedometer Display Dash 2018-2020 Please understand 2017 and older models require a different dash, even if yours looks the same. This is the factory Gauge/Screen. The dash is designed to auto pair, but sometimes it will not auto pair and you will have to program them together with buds software. This can be done at your local dealer or you can send in your ecu, key(s), and DPS (power steering) to us for programming. Contact for more information. It will display 0 miles, please record your current miles for your records. Current Part number: 710005553
New Maverick rear differential pinion housing nut socket tool. This tool will remove the nut that screws into the aluminum housing. Applying heat to the nut/housing is recommended before using this tool. There is no warranty with this tool. The nut should be left hand threaded, meaning turning counterclockwise will tighten the nut where clockwise will loosen it. Half inch drive socket. It is recommended to only use hand tools with this. Diameter (Exterior) 2 7/8" Diameter (Interior) 2 1/2"- OUT OF STOCK
NEW OEM BRP Thermostat Current part number 709200406 replaces 709200383 This style is external from the cylinder head. If you are unsure on fitment please contact us. 
OMC trunk seal for G2 Outlander This is an improved design over factory, this is much thicker and denser foam than the OEM gasket WILL NOT FIT G2L (models with steel racks) Replaces OEM part numbers: 293250275 219704369 293200163- OUT OF STOCK
NEW Outsiders Mud Crew Airbox seal This is an improved design over factory Apply a small amount of grease to aid install, this is much thicker and denser than the OEM o-ring or gasket Replaces OEM part numbers: 293300165 293300175 293300179 
MOOSE RACING HARD-PARTS Replacement Tie-Rod Ends 0430-0717 WILL NOT WORK WITH OEM TIE RODS Fits G2 ATV 2012-2018 with upgraded 12mm tie rods kit part number 0430-0674 This kit includes a pair of 12mm LH and RH ends, enough to repair one side of your ATV.
All Balls complete fuel pump module, retaining nut and gasket This fits G1 Models: 2009-2015 EFI Outlander 400 2009-2012 Outlander or Renegade 500 2009-2012 Outlander 650 2009-2011 Outlander 800R 2012 Outlander 800R XMR 2012 Outlander 800R MAX 2009-2011 Renegade 800R Part number: 47-1049 24-71022 Replaces OEM numbers: 703500766 703500781 709000194 709000245
Have Questions?
Our staff is available to answer questions
canampartsguy@gmail.com
1340 Okray Ave.
Plover, WI 54467
jared@canampartsguy.com
Cant find What you're looking for?
Visit our 
store!
2016 Can Am Parts, LLC. All rights reserved.