New Genuine OEM Works on 2014-2020 Commander and Commander Max (2011-2013 Do not have a oxygen sensor) 2013-2018 Maverick and Maverick Max 2017-2020 Maverick X3 and Maverick X3 Max 2018-2020 Maverick Trail 2019-2020 Maverick Sport 2017-2020 Defender and Defender Max If your machine has ECO mode it will have a oxygen Sensor from factory Part number 707600872
NEW EPI Primary Clutch Puller. PCP-15 (PCP15)
Fits: Can-Am 1000 Defender 2016+ HD8 DH10
Maverick Trail 2018+ 1000
Maverick Sport (all) 2018+
Maverick X3 (all models) 2017+Replaces oem 529000064
One piece style, manufactured from the highest quality steel
Precise machining on every model for accuracy
Heat treated for superior strength
- OUT OF STOCKInline fuel controller, this unit takes the fuel signal and modifies it based on throttle position and RPM inputs. Part number FC25009, please contact us if you have fitment questions. You can use a pre built map table or build your own custom map. Software is compatible with Power Commander, so you can download Power Commander maps to the unit Plug-n-play fuel management device pre-programmed with make/model specific maps Fully adjustable computer compatibility for ultimate tuning and personalization Use OEM-style connectors and high-quality wiring harnesses No computer necessary to modify fuel management Small, lightweight, and easy to fit on your bike Integrated O² optimizer where applicable
Used ECM (computer) with OEM Digital Key. This pair is tested, cleared of any codes and run on our shop ATV before leaving. Your Dash (speedometer) may need to be paired with BUDS. If you want to start and run the machine simply unplug the dash before installing the ecu. We provide the pairing service free of charge with purchase of ECU or Dash, contact us for further details. Only fits Generation 1 bikes Outlander and Renegade 500 2007 2008 2009 please note 2010 models use a different style ECU, this will not work on 2010 and newer Part Number: 420266491 420266495 710000817
Used ECM (computer) with OEM Digital Key.
This pair is tested, cleared of any codes and run on our shop ATV before leaving. Your Dash (speedometer) may need to be paired with BUDS. If you want to start and run the machine simply unplug the dash before installing the ecu. We provide the pairing service free of charge with purchase of ECU or Dash, contact us for further details.
Only fits Generation 1 ATV Outlander 650 2006 2007 2008 2009
please note 2010 models use a different style ECU, this will not work on 2010 and newer
Part Number: 420266501 420266505 710000817
Used ECM (computer) with OEM Digital Key.
This pair is tested, cleared of any codes and run on our shop ATV before leaving.
Your Dash (speedometer) may need to be paired with BUDS. If you want to start and run the machine simply unplug the dash before installing the ecu. We provide the pairing service free of charge with purchase of ECU or Dash, contact us for further details.
Only fits Generation 1 bikes Outlander and Renegade 800 HO 2006 2007 2008
Part Number: 420266374 420266623 710000817
Used 800 R ECM (computer) with OEM Digital Key.
This pair is tested, cleared of any codes and run on our shop ATV before leaving.
Your Dash (speedometer) may need to be paired with BUDS. If you want to start and run the machine simply unplug the dash before installing the ecu. We provide the pairing service free of charge with purchase of ECU or Dash, contact us for further details.
Only fits Generation 1 ATV’s Outlander 800R 2009 2010 2011 2012 MAX and Renegade 800R 2009 2010 2011
Part Number: 420266733 42026673, 420266738, 710000817
- This is the 2019+ rear differential found in Renegades and Outlanders 650 and larger This has the 6 inch (155mm) ring gear with straight cut teeth as shown. It will fit g2 bikes (500/650/800/1000) if you are upgrading you will need to shorten your shaft 1.75 inches or buy a kit from us, please see our other listings. (G1 bikes will require further modifications to work). This has a provision for an abs sensor, but will fit bikes without a rear diff sensor BRP claims 25% increase in load capacity on this gear set vs the spiral cut xmr final drive units (rear differentials) from 13-18 models. Pinion spline count 20 Current part number 705502808
- Rear driveshaft U-Joint Replacement 398 style Fits all V-twin Canam rear driveshafts XMR XT XXC XDS XRS STD Grease zerk in cap for easy maintenance Made in Japan High Quality Clips are included just as pictured We recommend pumping fresh grease in after installing, as the grease inside may not be enough for operation. Please note on some older driveshafts the yoke ears may need to be ground down to allow for the larger center part of the joint to be installed. Replaces OEM part numbers: 703500846 715900270 715900278
- SHIPS FREE TO THE LOWER 48 STATES This shaft has been cut and re-phased. Canam Maverick Rear prop shaft from gear box to rear differential. We install the guard. NEW # 703500994 Replaces:703500938,703500856, 705501849, 705502005, 703500994 20 spline gearbox yoke 20 spline differential yoke **Please note, this is the most updated shaft and does not require a wear ring on the differential side of the shaft. The last two pictures illustrate this.**
- Works on the G1 Outlander, G1/G2 Renegade, and nearly any other utility quad with available mounting area (8"x3") Includes 2 foot pegs and mounting hardware. Foot Pegs measure 9" long by 3" wide These Rox Speed FX Universal ATV Foot Pegs for utility quads have been designed to add aggressive traction to your OEM floor boards. Used by some of the top GNCC riders, these foot pegs are MADE IN THE USA and built to handle the dirtiest, nastiest terrain you can throw at them! Replaces OEM pegs 705000428 705003648 705002326
New Seizmik Halo R Convex Panoramic Rear View Mirror Seizmik Part Number: 18057 Fits 2.0? Round Tube ROPS (rollover protections system) and 1.875? Round Tube ROPS with shims We mounted this very easily in our Can-am Defender with a m8 bolt and nut in one of the factory holes. Features: Two Ball Joints—Maximizes range of adjustment High Impact ABS Plastic Housing—Resists damage Shatter Resistant Safety Glass—For maximum safety Convex Mirror Surface—Wider viewing range and image stabilization Built Tough—Heavy duty steel clamp with low mass design for maximum strength and durability Impact Resistant ABS Bezel—Protects and secures mirror glass and allows for easy glass replacement Seizmik Design—Styled to compliment all SEIZMIK side view mirrors UNLIMITED LIFETIME WARRANTY
NEW SEIZMIK STRIKE Side mirror set
Both drivers and passengers side mirrors
Fits 2.0″ Round Roll Cages or the 1.875″ Round Roll Cages with the supplied rubber shims
Features: Adaptive 360 Bracket Rotation: Will accommodate any angle roll cage pillar & provide optimal viewing position, so you can mount it high or low and adjust to perfect position every time
Full Breakaway Geometry: Designed to break away during impacts to prevent damage
Convex mirrors more than double your field of rear view
High-Impact ABS Plastic Housing: Resists damage
Ball Socket Joint: Provides a broad range of viewing angles
Heavy-Duty Steel Mounting Clamp: Low mass design provides maximum strength and durability
Convex Mirror Surface: provides wider viewing ranger and image stabilization
Shatter Resistant Safety Glass Position Tension Adjustment Bolt: Always be able to keep it tight as newUNLIMITED LIFETIME WARRANTY
CANAM Cage Styles
Defender: Pro Fit Cage
Maverick Trail/Sport: Pro Fit Cage
OG Maverick/Commander: Round 2.0”Part number 18092
- NEW SEIZMIK STRIKE Side mirror set Both drivers and passengers side mirrors Pro Fit mounts for the goofy looking D shaped with a channel roll cage will not fit round cages We test fitted these on our defender with the OEM flip glass windshield, there is enough room for the bracket to mount and the windshield to seal as it should. Features: Adaptive 360 Bracket Rotation: Will accommodate any angle roll cage pillar & provide optimal viewing position, so you can mount it high or low and adjust to perfect position every time Full Breakaway Geometry: Designed to break away during impacts to prevent damage Convex mirrors more than double your field of rear view High-Impact ABS Plastic Housing: Resists damage Ball Socket Joint: Provides a broad range of viewing angles Heavy-Duty Steel Mounting Clamp: Low mass design provides maximum strength and durability Convex Mirror Surface: provides wider viewing ranger and image stabilization Shatter Resistant Safety Glass Position Tension Adjustment Bolt: Always be able to keep it tight as new UNLIMITED LIFETIME WARRANTY CANAM Cage Styles Defender: Pro Fit Cage Maverick Trail/Sport: Pro Fit Cage OG Maverick/Commander: Round 2.0” Part number 18093