New OEM bushing kit for Commander, G2 Renegade and G2 Outlander This is a genuine OEM kit with bushings and wear plate. Order two (2) per arm. One kit does one attachment point. Part numbers: 706202088 706202089 706202133 703500875
HD Clutch bolt set for most every Can-am V-twin 2006 to current. Will not work on: Maverick Turbo Maverick X3 Maverick Sport Maverick Trail Defender These will swap out the factory Torque To Yield (TTY) bolts/studs. M10 and M12 Black-Oxide Alloy Steel Socket Head Bolt These are class 12.9 bolts, with a tensile strength of 170,000 psi, these alloy steel bolts are stronger than Grade 8 steel bolts. 8 and 10mm Allen Sockets required to install these bolts. 18-8 Stainless Steel Single-Wave Washers included, these help prevent loosening, use with your existing washers. Installation Torque Specs: 80 ft·lb On the Primary Bolt 45 ft·lb On the Secondary Bolt (red thread locker recommended, allow to set up overnight)
New short wiring harness for rear tail lights Will need to be wired in to work. This plugs in to Tail light part number 710001645 Fits: G2 ATV's with dual tail lights, Commanders, and Mavericks (non X3/Sport/Trail)
20 Spline Yoke with Wear ring installed. Fits: XMR 1000, Maverick and '14&newer Commander style Rear differentials. These yokes are made to very tight tolerances, if you are not careful when installing these you can damage the yoke or your pinion shaft. We recommend you take your time and clean the pinion gear before installing. ---Great for custom applications--- Uses Factory size U joint (398 at the auto parts store) Part numbers 715900271 705400036- Sale!
New take off gearbox side, 20 spline yoke. This fits on large gearboxes output shafts. 20 spline yoke partially machined to accept a protector ring. This is the forward most yoke on the REAR driveshaft. Works with 398 U joints. found on Vtwin rear driveshafts. Part number 715900129 replaces 705501373 and 715900234 
Brand NEW OEM Tail Light Assembly Found in G2 Renegade and Outlander, Commander and Maverick. Fits left or right. Part Number 710001645
New Rear tail light Fits: 2007-2012 Renegade G1 and 2008-2015 DS 450. Part Number 710001041
New Can Am Maverick Rear Differential Pinion Seal This is a New Genuine OEM seal Part number 705501933 New updated part number 705502276 Press fit into differential, then seals against wear ring (if your driveshaft requires one) If your wear ring is grooved you should replace it.
Black wrap around wind deflector set with mounting kit. Fits Outlander, Renegade, & DS450. Both are brand new. Part numbers 715001378 715001706
White wrap around wind deflector set with mounting kit. Fits Outlander, Renegade, & DS450. Both are brand new. Part numbers 715000537 & 715001378
Orange wrap around wind deflector set with mounting kit. Fits Outlander, Renegade, & DS450 Both are brand new. Part numbers 715003813 & 715001378 Orange Crush matches 2020 and prior models.
Wind deflector mounting kit with hardware. Fits Outlander Renegade & DS450. For use with OEM wind deflectors This is just the mounting kit. Part number 715001378 No wind deflectors included.
SHIPS FREE TO THE LOWER 48 STATES Moose Racing Complete Engine Gasket Kit with Oil Seals. Fits 800 or 1000 Commanders 2011-18 Moose Racing Part Number 0934-4834 Replaces 420684150
Brand New OEM Water Pump Rotary Seal. Will fit most Can-Am models. Part Number 420650370
SHIPS FREE TO THE LOWER 48 STATES NEW OEM Gearbox Angle Rotation Sensor (gear position sensor) This is used on the Large Gearbox Part Number 420266168
Can-am Style Plastic Fender rivet set. NEW Pack of 25 For 8mm (5/16?) holes great for holding plastic fenders together, works on Maverick, Commander, Outlander and Renegade Replaces part numbers 293150089 293150230
CVT Rear Boot (the boot that connects to the exhaust side of the inner CVT cover plate. This is the updated part and will work on all G1 V-Twin ATV’s . This replaces 707000789, this newer style will not work on the xmr 2011-12 where the exhaust riser pipe meets the upper tube. Current Part Number 707001274- OUT OF STOCK
Brand new Genuine OEM flexible CVT intake adaptor for Renegade, Outlander, Maverick, and Commander.
This replaces the thin rubber boot that comes on many early CanAm V-Twin models.
Very nice upgrade for a cracked CVT intake boot.
Current part number 707002585
Previous part numbers 707001467, 707001043, 707000719
New Can Am spark plug boot connector part number 420265020 Will only work with spark plug style that is pictured Easy to replace. Just unscrew your old one and screw on your new one. Fits: 2013-2018 Maverick 1000R Turbo or Non Turbo 2018-2020 Commander 1000R 2016-2020 Outlander or Renegade 850/1000R 2015+ Outlander 450
EPI Lower Ball Joint Replaces
OEM part #706202045
Manufacturer Part Number: WE350045
Fits: Gen 2 Outlander Renegade Commander Maverick (non X3/trail/sport)
Brand NEW EPI Upper Ball Joint
For Gen 2 bikes, Commander and Maverick (non Sport/Trail/X3)
Includes Circlip, Cotter Pin, Hardened Washer, and Nut.
Replaces OEM #: 706202044
Manufacturer Part Number: WE350043
New Genuine OEM Can-am radiator cooling fan assembly Fits on some G2 Outlander/Renegade and OG Maverick, please check part numbers for fitment. Will not fit XMR Outlander’s Current part number 709200564 Old part number 709200309 709200462
OEM Radiator Relocate Kit. This moves your radiator (not included) up on your front rack. (will not fit 22+ XXC models) This is a must for tackling extreme mud conditions where you risk clogging your radiator and overheating your engine! Allows for easy servicing (cleaning) This is a factory OEM kit, not an aftermarket kit, instructions are provided on BRP’s website. Coolant overflow tank is included, hoses ect.. You will not find a better fit and finish kit on the market. There is drilling and cutting involved. This is all covered in great detail. Roughly 3.5 hour install time This kit fits G2 and G2L models check out the pictured fitment chart if you are unsure what you ride. The white “can-am” is a protective film that can be removed with a small pick. Part number 715001930
New Genuine OEM power steering stem for Outlander and Renegade This will only fit power steering models Will not work on NON power steering bikes Current Part number 703501137 Old Part Numbers 709400703 709401843
SHIPS FREE TO THE LOWER 48 STATES Can-am Commander style CVT cover set. This is the 13 bolt cover set, with attached reflective heat foam. Fits: Commander 800R two seat 2011-2020 Commander 800R MAX four seat 2016 Commander 1000 two seat 2011-2017 This kit will keep the water out! Comes with: Commander covers inner and outer. CVT Cover Gasket CVT Drain plug and Clamp Engine O-ring Gear box O-ring Inner CVT Bolts/Nut 13 Cover screws Part numbers: 420612472 715900200 420611407 420440568 420430408 420631088 420430126 420440567 420440568
OEM Upper ball joint for G1 ATV’s Also works in Renegade Lower arms. Current Part number 706200653 Replaces: 703500063, 706200024, 706200091
New OEM Ball Joint for 2006-2012 Gen 1 Can-Am Outlanders 706200444 This is the bolt in style. DOES NOT come with bolts.
Have Questions?
Our staff is available to answer questions
canampartsguy@gmail.com
1340 Okray Ave.
Plover, WI 54467
jared@canampartsguy.com
Cant find What you're looking for?
Visit our 
store!
2016 Can Am Parts, LLC. All rights reserved.