All Balls dual row tapered wheel bearing Features: High contact double lip seals with armor shield O-rings sealing ID of bearing for superior water and dirt exclusion High performance tapered bearing deliver on average 95% better static load and 86% dynamic load capabilities Hardened steel 52100 and tempered for maximum durability WILL NOT work with the Maverick X3 Replaces: 293350118, 705400088 and 293350040 Unsure on fitment? Here are the dimensions: 30mm Inner Diameter 60mm Outer Diameter 37mm Wide Seal included, not all applications use the seal.
- All Balls dual row tapered wheel bearing for Maverick X3 replaces OEM numbers 293350109 293350129 High contact double lip seals with armor shield O-rings sealing ID of bearing for superior water and dirt exclusion High performance tapered bearing deliver on average 95% better static load and 86% dynamic load capabilities Hardened steel 52100 and tempered for maximum durability
- Brand NEW aftermarket primary clutch two way bearing with shims Current part number 22-51782 Includes new bearing and two washers This two way bearing service kit includes everything you need to replace the two way bearing on the primary clutch. The thrust washers install on either side of the two way bearing. Replacing this bearing is a great place to start if you experience hard shifting, creeping while in gear or premature belt failure. This kit replaces the two way bearing, 42083235, 420233418 and both thrust washers 420427220 Will not fit mavericks with a rear driveshaft, if you have fitment questions please reach out, we are here to help.
- New aftermarket switch replaces OEM part numbers: 710008837 710005070 710000791 710004618 703500920 710003062 710002883 710003039 710004041 Fits on: 2006-2019 Outlander and Renegades 500 650 800HO 800R 850 1000 1000R 2020 Outlander 650 STD DPS XT XMR 2020 Outlander 6x6 650 or 1000 2020 Renegade 570 XMR Will not work on 400’s or machines with drive by wire. 3 position headlight switch OFF/Low/High beam Will come as pictured Please look at the plug style on your current switch. The buttons may be arranged differently than the switch you are replacing. We have found this switch will work on DPS or non DPS equipped machines
- NEW Bronco Can Am 62" wide Defender Shock Kit Front And Rear. Please note there are various suspension widths offered for the Defender, these will only work correctly with the 62" wide models. If you have a fitment question we are here to help!Features:
- Bronco gas shocks offer long term consistent performance over stock oil only damped shocks
- 10% stiffer springs provide a better ride and higher load capacity
- Works great on the front to better support your snowplow and on the rear when hauling cargo
- Direct bolt-on replacement: pre-installed spring allows for quicker setup
Set of four Bronco gas shock kit for G1 Outlander 650/800 or Renegade 500/800
These shocks are the same length on all four corners, you may notice a slight lift, more so on a well used machine.
*Please note these will not work in place of struts found on the Outlander 400/500 machines.
Features:
Bronco gas shocks offer long term consistent performance over stock oil only damped shocks
10% stiffer springs provide a better ride and higher load capacity
Works great on the front to better support your snowplow and on the rear when hauling cargo
Smooth black color blends perfectly on your machine
Direct bolt-on replacement: pre-installed spring allows for quicker setupP/N AU04414X4
Features:
Cable adapter and fasteners constructed of highest quality stainless steel
Gold anodized aluminum throttle lever can be operated with one finger for safer side hilling
Safety features include rubber accordion boot (keeps moisture out of cable housing) and safety pin (locks left throttle from unwanted use)
Kit includes all hardware, allen wrenches and instructions for installation in approximately 20 minutes
Part Number 12-71042
Brand Number: 007-1011A