Used OEM Can Am Outlander and Renegade rear brake lever or brake pedal. It will fit any 2006-2012 Outlander or Renegade 400, 500, 650 and 800. Great shape not bent. Comes as pictured
This is the 2019+ rear differential found in Renegades and Outlanders 650 and larger This has the 6 inch (155mm) ring gear with straight cut teeth as shown. It will fit g2 bikes (500/650/800/1000) if you are upgrading you will need to shorten your shaft 1.75 inches or buy a kit from us, please see our other listings. (G1 bikes will require further modifications to work). This has a provision for an abs sensor, but will fit bikes without a rear diff sensor BRP claims 25% increase in load capacity on this gear set vs the spiral cut xmr final drive units (rear differentials) from 13-18 models. Pinion spline count 20 Current part number 705502808
New Genuine OEM Rear Differential Lock Switch Only works on models with turf mode Part number 710005470
New Genuine OEM Fits G2 machines from 2012-2018 Perfect for plowing snow or hauling heavy loads Improves handling 14.5" long with a I.D of 2" Part number 715003200
Rear driveshaft U-Joint Replacement 398 style Fits all V-twin Canam rear driveshafts XMR XT XXC XDS XRS STD Grease zerk in cap for easy maintenance Made in Japan High Quality Clips are included just as pictured We recommend pumping fresh grease in after installing, as the grease inside may not be enough for operation. Please note on some older driveshafts the yoke ears may need to be ground down to allow for the larger center part of the joint to be installed. Replaces OEM part numbers: 703500846 715900270 715900278
Red wrap around wind deflector set with mounting kit. Fits Outlander, Renegade, & DS450. Both are brand new. Part numbers 715003811 & 715001378
Brand New OEM Helix Cam. Fits all non-turbo Maverick and Maverick MAX from 20013-2018. Also fits 2018+ Commander 1000R & Commander MAX 1000R Part number 420280474
New Genuine OEM Mounting kit sold separately Part number 715003811
2016-2020 Commander Fan Assembly We installed a new motor in this. Part number 709200566
SHIPS FREE TO THE LOWER 48 STATES This shaft has been cut and re-phased. Canam Maverick Rear prop shaft from gear box to rear differential. We install the guard. NEW # 703500994 Replaces:703500938,703500856, 705501849, 705502005, 703500994 20 spline gearbox yoke 20 spline differential yoke **Please note, this is the most updated shaft and does not require a wear ring on the differential side of the shaft. The last two pictures illustrate this.**
OEM radiator fan. Fits 2013-2024 Outlander XMR Light Scuffs and Scratches. Comes as Pictured.Current part number 709200565 replaces 709200458
Works on the G1 Outlander, G1/G2 Renegade, and nearly any other utility quad with available mounting area (8"x3") Includes 2 foot pegs and mounting hardware. Foot Pegs measure 9" long by 3" wide These Rox Speed FX Universal ATV Foot Pegs for utility quads have been designed to add aggressive traction to your OEM floor boards. Used by some of the top GNCC riders, these foot pegs are MADE IN THE USA and built to handle the dirtiest, nastiest terrain you can throw at them! Replaces OEM pegs 705000428 705003648 705002326
Secondary Clutch Thrust Washer M10 Hole for use with bolts or studs Current Part number 420627590 Replaces 420627591 711627591
New Seizmik Halo R Convex Panoramic Rear View Mirror Seizmik Part Number: 18057 Fits 2.0? Round Tube ROPS (rollover protections system) and 1.875? Round Tube ROPS with shims We mounted this very easily in our Can-am Defender with a m8 bolt and nut in one of the factory holes. Features: Two Ball Joints—Maximizes range of adjustment High Impact ABS Plastic Housing—Resists damage Shatter Resistant Safety Glass—For maximum safety Convex Mirror Surface—Wider viewing range and image stabilization Built Tough—Heavy duty steel clamp with low mass design for maximum strength and durability Impact Resistant ABS Bezel—Protects and secures mirror glass and allows for easy glass replacement Seizmik Design—Styled to compliment all SEIZMIK side view mirrors UNLIMITED LIFETIME WARRANTY
NEW SEIZMIK STRIKE Side mirror set
Both drivers and passengers side mirrors
Fits 2.0″ Round Roll Cages or the 1.875″ Round Roll Cages with the supplied rubber shims
Features: Adaptive 360 Bracket Rotation: Will accommodate any angle roll cage pillar & provide optimal viewing position, so you can mount it high or low and adjust to perfect position every time
Full Breakaway Geometry: Designed to break away during impacts to prevent damage
Convex mirrors more than double your field of rear view
High-Impact ABS Plastic Housing: Resists damage
Ball Socket Joint: Provides a broad range of viewing angles
Heavy-Duty Steel Mounting Clamp: Low mass design provides maximum strength and durability
Convex Mirror Surface: provides wider viewing ranger and image stabilization
Shatter Resistant Safety Glass Position Tension Adjustment Bolt: Always be able to keep it tight as newUNLIMITED LIFETIME WARRANTY
CANAM Cage Styles
Defender: Pro Fit Cage
Maverick Trail/Sport: Pro Fit Cage
OG Maverick/Commander: Round 2.0”Part number 18092
NEW SEIZMIK STRIKE Side mirror set Both drivers and passengers side mirrors Pro Fit mounts for the goofy looking D shaped with a channel roll cage will not fit round cages We test fitted these on our defender with the OEM flip glass windshield, there is enough room for the bracket to mount and the windshield to seal as it should. Features: Adaptive 360 Bracket Rotation: Will accommodate any angle roll cage pillar & provide optimal viewing position, so you can mount it high or low and adjust to perfect position every time Full Breakaway Geometry: Designed to break away during impacts to prevent damage Convex mirrors more than double your field of rear view High-Impact ABS Plastic Housing: Resists damage Ball Socket Joint: Provides a broad range of viewing angles Heavy-Duty Steel Mounting Clamp: Low mass design provides maximum strength and durability Convex Mirror Surface: provides wider viewing ranger and image stabilization Shatter Resistant Safety Glass Position Tension Adjustment Bolt: Always be able to keep it tight as new UNLIMITED LIFETIME WARRANTY CANAM Cage Styles Defender: Pro Fit Cage Maverick Trail/Sport: Pro Fit Cage OG Maverick/Commander: Round 2.0” Part number 18093
SP1 Radiator Relocation Kit Replacement Latch Kit. Replaces OEM 860200239 517303981 517304075 Kit includes 2 Latches. Enough to retain one radiator access panel.
New Genuine OEM Handlebar Wind Deflector. Part number 715006117
Standard Differential Pinion Seal. Please check your wear ring, if that is grooved it is time to replace. Very easy to miss that and blame a new seal on a bad wear ring. Will fit: G1 Front and Rear Differentials 2012-18 Outlander and Renegade Front and Rear Differentials All Commander Front Differentials 2011-13 Commander Rear Differentials 2013-18 Maverick Front Differentials (non X3/trail/sport) WILL NOT FIT G2 XMR 800/850/1000 REAR DIFFERENTIAL Measurements are shown: 70mm outside and 37mm inside Replaces part numbers 705401481 and 705401615
Please verify your differential uses this style of Seals before ordering! Can Am Front Differential Pinion and Axle Seals (Timken) Fit on most all 2006-2019 Outlanders and Renegades Also fits Commanders and Mavericks (non X3/Sport/Trail) The Pinion Seal has a 70mm Outer Diameter And the standard 37mm inner diameter. Replaces part numbers 705401481 705500255 705500081 The Axle Seal has a 47mm Outer Diameter And the standard 25mm inner diameter. Replaces part numbers 705401618 705401486 Complete Seal kit for Standard Front Differentials
NEW OEM Throttle Body Air Intake Neck Fits 850/1000 ATVs and 800R/10000 Commanders On ATV’s this connects the throttle body to the intake manifold On Commanders this connect the “Y” intake manifold to the 90* fitting Part number: 420267045
High quality Timken axle oil seal. Fits ATV front differentials 2006-current, some UTV's To be 100% sure on fitment, measure your outer diameter on your seal, it should read 47mm This seal has a 25mm inner diameter 47mm outer diamter and is 7mm thick. Replaces OEM 705500255 705500081 Order qty two per machine.
High quality Timken axle oil seal. Fits ATV rear differentials 2006-2014 To be 100% sure on fitment, measure your outer diameter on your seal, it should read 47mm This seal has a 30mm inner diameter 47mm outer diamter and is 7mm thick. Replaces OEM 705500751 705501196 and 705501996 Order qty two per machine.
SHIPS FREE TO THE LOWER 48 STATES This will replace the functionality of the VISCO Lock in any Can-am Front differential. 2006 to Current including X3. Installs in place of the “spider gears” Will not fit models with an electronic smart lok front differential Very simple to install. One measurement to make. The TORQ Locker is the most advanced, strongest, highest quality automatic locking differential on the planet, proven in the most extreme vehicles from hard-core Rock Crawling, racing the King of the Hammers, Rock Bouncing, Sand Dunes and Mud Drags. To back this all up, Torq-Masters Industries offers an unprecedented 2 year warranty on the TORQ Locker with no tire size, horsepower limits or loopholes. Torq-Masters Industries is committed to building the highest quality locking differentials possible. To be the best, we build with the best, TORQ Locker is 100 percent Made in the USA with 100 percent USA raw materials. Keep it Simple, no air-lines to leak, compressors to fail, cables to adjust or electrical gremlins, the TORQ Locker gives you piece of mind as a reliable, mechanical, automatic locker that can handle any terrain. The TORQ Locker design eliminates and integrates pesky locker components seen in all other automatic drop-in lockers. The spacers are gone and the dowel pins are now machined into the Cam Gears to form key-ways. The innovative design features of the TORQ Locker have three game-changing benefits: No dowel pins to install or fail. The Key-Way design of the Cam gears can’t shear, ever. Easiest Locker on the market to install, no spacers, no dowel pins, one measurement. Best On-Road manners of any automatic locker; the Key-Way design is more forgiving than the rigid dowel pin design. The Key-Way allows for smoother locker engagement. By eliminating the spacers they eliminated the leading cause of the pop some people experience with automatic lockers. Listing is for the TORQ Locker only. Differential carrier shown in pictures is for reference only.
UNI Foam air filter You will need to oil this filter before use. Fits SXS pictured: Commanders 800/1000 and Maverick 1000R (non turbo) (non X3/Sport/Trail) Unsurpassed in airflow, stopping dirt and overall performance Two-stage air filters come apart for maximum airflow and ultimate cleaning Most filters feature the Ultra Seal grease groove on the sealing surface Each fits in stock air box exactly like OEM filter Clean easily with grease-cutting dish washing detergent; just clean, oil and reuse indefinitely Flexible seams that will not crack Filters are designed to fit all stock air boxes Made in the U.S.A. Replaces OEM 707800327
New OEM bushing Will work on upper and lower a arm Part Number: 706201659 Will come as pictured
Used Water deflector, this passively covers the cvt inlet pipe from splashes of water/mud kicked up from the front wheel/tire. This part is in good working order with normal scuffs and scrapes from off road use. Fits 2007-09 Renegade 500, 800HO and 800R Part number 707000509- OUT OF STOCK
Aftermarket Four wheel drive servo motor. This is what engages the sliding collar putting power to the front differential. Part number 715900614 420891087 415129174 
USED OEM Rear master cylinder cover for G1 Renegade 500 800HO 800R Part numbers 705003325 705003650 705002410
Used OEM 2011-2015 Commander, and 2015 maverick safety net buckle Product Number: 707900035 Comes as pictured
Used- Like New OEM 2011-2020 commander rail end cap Sold as a Pair Product Number: 708300333 Comes as pictured
Used- Good Condition, completely checked over and tested, works as it should OEM 2015 800, and 1000 Commander Short Wheel Base Electrical Harness This Electrical Harness is the Chassis Only Product Number: 710004332 Comes as Pictured
Used- Like New OEM 2014-2015 Maverick 1000, ECM Part Number: 420264800 Updated Part Number: 420264802 Comes as Pictured
USED OEM G1 Can Am Renegade Spring Set. Front Spring Part Number 706200829 Rear Spring Part Number 706000654
Used- Good Condition OEM Protector Ring for 2011-2020 Commander Standard Shocks Measurements: Inner 50mm Outer 85mm Product Number: 706000911 Comes as Pictured
Used OEM Rear Cargo Support, fits 2011-2018 commander Product Number: 708300183 Comes with hardware for installation
Have Questions?
Our staff is available to answer questions
canampartsguy@gmail.com
1340 Okray Ave.
Plover, WI 54467
jared@canampartsguy.com
Cant find What you're looking for?
Visit our 
store!
2016 Can Am Parts, LLC. All rights reserved.