Shop

  • OEM CANAM BRP Exhuast Muffler Clamp Part Number 293650177 Fits 2.25" OD pipe
  • Wind deflector mounting kit with hardware. Fits Outlander Renegade & DS450. For use with OEM wind deflectors This is just the mounting kit. Part number 715001378 No wind deflectors included.

  • Brand New Genuine OEM ignition key switch for Outlander G1 or Renegade G1 Does not require BUDS tuning to swap out, your current DESS key will turn in this. The ignition switch is just a reader of the coded key. Key sold separately. Old Part Numbers 710000728 and 710001421

  • SHIPS FREE TO THE LOWER 48 STATES Late G1 Early G2 Standard Rear Differential Bearing and Seal Kit High quality aftermarket bearings along with double lip axle seals. Bearing and Seal Brands include: Nachi, KOYO, NTN, Timken The large case sealing and pinion gear O-rings are NOT included as a cost saving measure, these O-rings are reusable if not damaged. There are a few options for kits, please verify your differential uses this style of gears before ordering! This will only fit six mounting hole differentials. Open up the differential! Check for two bearings total (one on each side) on the ring gear. If you only have two proceed to the next measurement. Measure your outer diameter of your axle seals! They should measure close to 1 3/4" (47mm) To further verify fitment you can measure your pinion pilot shaft, this should be 9/16″ (14mm) The last pictures show this very clearly. Please take the time to measure your parts before buying this will save time and restocking fees.
  • NEW OEM Throttle Body Air Intake Neck Fits 850/1000 ATVs and 800R/10000 Commanders On ATV’s this connects the throttle body to the intake manifold On Commanders this connect the “Y” intake manifold to the 90* fitting Part number: 420267045

  • Brand New Genuine OEM Friction Washer Goes between Ball Bearing and Spring Seat on the Drive Pulley Clutch

    This is needed for correct engine braking on many models, not sure if you need it, please ask!

    OEM Part number: 420460430

  • SHIPS FREE TO THE LOWER 48 STATES 0934-3019 Moose Racing Gasket Kit Fits Outlander/Renegade 800 models. Complete kit with oil seals. Center case gasket Magneto Cover Gasket PTO Cover Gasket Two Cylinder base Gaskets Two Cylinder Head Gaskets Two Valve Cover Gaskets Water Pump Cover Seal (kit does not come with mechanical seal)
  • Can-am Outer CVT Cover, belt box. This is the updated 13 bolt cover. Works with 7 or 13 bolt inner covers. This will fit on any 2006-current v twin ATV, Renegade or Outlander, 500 650 800 or 1000. If you have a a stud with a nut retaining your primary clutch this cover does not have the depth needed.  Many 1000R machines use a stud/nut in place of the bolt. Unsure on fitment, please ask! This will keep the water out! 13 Cover bolt holes Current Part number is: 420611397 Replaces: 420611395,  420611390, 420611391, 420611393

  • NEW OEM Can-am Output Crank Shaft Seal This is the engine out put shaft seal, pressed into the crankcase PTO cover 34mm Inner Diameter 52mm Outer Diameter 8mm Thick Current Part Number 420631933 Replaces Part Number 420631932
  • New OEM Torx Screws Comes as a set of 11 Will fit on the following 2016-2019 Defender HD8 and HD10 2018-2019 Maverick Trail 800R and 1000R 2019 Maverick Sport 1000R
  • These dashes are found on many machines.

    2014-2017 Maverick, Commander, Renegade and Outlander models with the Standard Digital Dash Mount This is the factory Gauge/Screen.

    The dash is designed to auto pair, but sometimes it will not auto pair and you will have to program them together with buds software. This can be done at your local dealer or you can send in your ecu, key(s), and DPS (power steering) to us for programming. Contact for more information.

    It will display 0 miles, please record your current miles for your records.

    Current part number:  710005087

    Replaces part numbers: 710003851 710003924 710005024 710005208

  • NEW OEM Mode Switch Menu/Trip Found on 2020+ Outlander 850 1000R Part number 710006717