New OEM Gasket Will fit the following 2016-2019 Defender HD8 and HD10 2018-2019 Maverick Trail 800R and 1000R 2019 Maverick Sport 1000R- OUT OF STOCK
Brand New Genuine OEM Shifting cable for two passenger Canam Mavericks and Commanders WILL NOT FIT Maverick Trail/Sport or X3 WILL NOT FIT Four Seat Models Comes as pictured OEM part number 707000775 - OUT OF STOCK
Can-am Shim Kit for XMR G2 800 or larger 2012-current Rear Differentials. Part number 703500835 
OEM Rotax Cylinder Base gasket Fits many Canam ATV’s/UTV’s 330 400 500 650 800 1000 Unsure on fitment? Please ask! Part number 420630210
NEW OEM Thermostat 150*F Rating This is the style that is mounted in the front cylinder head. Part number 420222494 replaces 420222493 and 711222493
NEW OEM Shim Kit for standard pinion gears. Wide Range of shims, this will allow you to set up your pinion depth. 37mm Outer Diameter. 27.45mm Inner Diameter. This is a loose fit Fits Front or Rear Standard Differentials Part number 705502061
Can Am Commander or Maverick Wheel Stud M10 Stud diameter 27.5mm spacing for brake rotor Part number 250300060 replaces 250300051
20 Spline Yoke Fits: XMR 1000, Maverick and ’14 & newer Commander style Rear differentials. You will need a wear ring if you are using this on the differential side of the shaft. These yokes are made to very tight tolerances, if you are not careful when installing these you can damage the yoke or your pinion shaft. We recommend you take your time and clean the pinion gear before installing. —Great for custom applications— Uses Factory size U joint (398 at the auto parts store) Part numbers 715900271
Air Pressure sensor, this goes in the Black plastic Intake manifold. Will work on any 2006 to current Can am Outlander, Renegade, Commander, Maverick, Defender 500 570 650 800 850 1000 XT XMR MAX or XXC The Manifold Absolute Pressure sensor or MAP sensor is a sensor that is attached to the intake manifold. The MAP sensor responds to changes in the intake manifold pressure (vacuum) and provides a reading of engine load. How it works is 5 volts DC is supplied to the sensor from the ECU. Inside the MAP sensor there is a resistor that moves in relation to intake manifold pressure. The resistor varies the voltage between about 1V to 4.5V (depending on engine load) and that voltage signal is returned to the PCM to indicate manifold pressure (vacuum). This signal is essential for the PCM to determine fuel delivery. Part numbers: 420874650 707000564 707000995 0 261 230 030 ALFA ROMEO 46553045 ALFA ROMEO 46533518 CHERY S21-3614021 FIAT 46553045 FIAT 77364869 FIAT 7084986 FIAT 0000046553045 FIAT 46533518 LANCIA 46533518 LANCIA 0000046553045 LANCIA 46553045 MOOSE 2120-0994 PROTON PW810694 ROTAX (BOMBARDIER-ROTAX GMBH) 874 650 SCANIA 5166434
Used ECM (computer) with OEM Digital Key.
This pair is tested, cleared of any codes and run on our shop ATV before leaving.
Your Dash (speedometer) may need to be paired with BUDS. If you want to start and run the machine simply unplug the dash before installing the ecu. We provide the pairing service free of charge with purchase of ECU or Dash, contact us for further details.
Only fits Generation 1 bikes Outlander and Renegade 800 HO 2006 2007 2008
Part Number: 420266374 420266623 710000817
Brand new inner secondary clutch This inner clutch has the hole for the pig tale style spring but will work on springs without the pig tale. New OEM Part Part Numbers : 420280499 420280235 420248233 420280236 420280238 420280497
OEM Radiator Relocate Kit. This moves your radiator (not included) up on your front rack. This is a must for tackling extreme mud conditions where you risk clogging your radiator and overheating your engine! Allows for easy servicing (cleaning) This is a factory OEM kit, not an aftermarket kit, instructions are provided on BRP’s website. Coolant overflow tank is included, hoses ect.. You will not find a better fit and finish kit on the market. There is drilling and cutting involved. This is all covered in great detail. Roughly 3.5 hour install time This kit fits G2 and G2L models check out the pictured fitment chart if you are unsure what you ride. The white “can-am” is a protective film that can be removed with a small pick. Part number 715001930
BRAND NEW Can Am OEM Wheel Cap This is for ONE (1) Single Cap Part Number 705400928 There is more than one style. Please verify that this is the correct style BEFORE ordering.
Set of four Bronco gas shock kit for G1 Outlander 650/800 or Renegade 500/800
These shocks are the same length on all four corners, you may notice a slight lift, more so on a well used machine.
*Please note these will not work in place of struts found on the Outlander 400/500 machines.
Features:
Bronco gas shocks offer long term consistent performance over stock oil only damped shocks
10% stiffer springs provide a better ride and higher load capacity
Works great on the front to better support your snowplow and on the rear when hauling cargo
Smooth black color blends perfectly on your machine
Direct bolt-on replacement: pre-installed spring allows for quicker setupP/N AU04414X4
New Genuine OEM Air Outlet for Can Am Outlander Gen 2
Part Number 707001496
NEW Genuine Can-am Rear Prop Shaft for G1 STD single seat machines WILL NOT FIT MAX. This will work with 2006-2011 500 650 800 800R, Outlander or Renegade and 2012 Outlander 500 650 or Renegade 500. The picture is what you will get. We install the wear ring and deflector ring for fast install. Current Part number: 703500801 Previous numbers: 703500767 703500719 705500816 703500704
Heavy-duty ball joint kits feature durable steel-on-steel design and an adjustable end cap, which allows slop to be taken up as they wear
Greased zerk fitting for easy grease delivery
Replaces OEM part numbers: 706202044 706200741 706201370 706201394
G2 ATV’s Commander, Maverick. Unsure on fitment? Please ask!
Moose Racing number 0430-1036
Can-am Maverick Turbo Rear prop shaft from gear box to rear differential. Will fit the regular maverick turbo, the xds turbo and the xrs turbo in both 2 seat and max frame. We install the wear sleeve and guard. Current Part Number: 703500939 Previous Part Number: 703500877
Can Am Maverick 1000R secondary spreader M25x1.5 thread size, to verify fitment 100% measure your clutch where this threads in. This works on the QRS style secondary clutches pictured. This will NOT work on the X3 models Bolt is not included Part number 708200504
SHIPS FREE TO THE LOWER 48 STATES New OEM Outer Variator Cover for Maverick X3 and X3 MAX Part Number 420212508 replaces 420212505
Moose Racing Radiator Cap Fits Outlander, Renegade, Commander, Defender and Maverick Unsure on fitment, please ask us. Cap is set to the same 15.9PSI as stock. If you current cap is not holding pressure replacing with new will help avoid overheating. Replaces OEM 709200207 709200033
Genuine OEM Start/Stop Switch
This has the additional single light blue wire with connector.
Current Part Number: 710006134
Fits some 2019 Outlander and Renegade 1000R, 2020 Outlander and Renegade 850/1000R
Please contact us if you are not 100% sure on fitment, we will be happy to assist
SHIPS FREE TO THE LOWER 48 STATES New Throttle Handle and 4×4 Switch Current Part Number: 707000595 Old Part Numbers: 709400186 707000369
Brand New OEM Reverse Override Rocker Switch Fits: Commander, Maverick and Maverick Turbo, Maverick X3, Not compatible with Maverick Sport/Trail or Defender If you aren’t sure if this will fit, please ask, we will help! Part number 710002053
Have Questions?
Our staff is available to answer questions
canampartsguy@gmail.com
1340 Okray Ave.
Plover, WI 54467
jared@canampartsguy.com
Cant find What you're looking for?
Visit our 
store!
2016 Can Am Parts, LLC. All rights reserved.