- LED dimmer facilitates reading temperature settings.
- 4 temperature settings with individual controls for thumb and grips.
- Returns to previous heat setting.
- One-touch shutdown.
- Wiring Harness (710004567) required for installation, on G2L and G2S (except 1000R and T category models) G2 Outlander does not require the harness.
- SHIPS FREE TO THE LOWER 48 STATES
- 2012-2018 G2 ATV Rear Differential Swap Kit Kit includes: Rear Differential, Rear driveshaft, Bolt and Washer. This kit includes a rear differential with: Tapered roller bearings Three bearings on the pinion gear 6 inch diameter ring gear Your choice of gear style, spiral bevel or straight cut. Both have the same 3.60 ratio as your current differential. Spiral Bevel Gears are sourced from the 2013-18 800 850 and 1000 XMR differentials. Current part number 705502546 Old part numbers: 705502178 & 705502090 Straight Cut gears are sourced from the 2019+ 650+ differentials. Current part number 705502808 The driveshaft included is an OEM shaft with the correct end yokes for your application. The differential end yoke will not use a wear ring, this has been done away with by BRP the yoke is what the pinion seal touches now. You will need to fill the differential with 250ml (8.4oz) of 75W-140 gear oil and transfer over your fill plug and washer. The torque spec on the driveshaft retaining bolt is 55ftlbs with thread locker applied. Some minor trimming on the brackets that surround the differential is required. These differentials have the provision for an ABS sensor, this is standard on euro models, for mud riders state side, you can fill this hole with RTV or leave it open. If you are running the silver protector ring on your axle, you will need to push the ring outward slightly. We choose to remove these dust covers as they tend to trap debris when run under water.
- OUT OF STOCK
New OEM Plastic Shift Arm Base Fits G2 Outlander or Renegade Part numbers: 707000971 707002439
- OUT OF STOCKNew Genuine OEM Air Outlet for Can Am Outlander Gen 2 Part Number 707001496
- OUT OF STOCK
OEM Radiator Relocate Kit. This moves your radiator (not included) up on your front rack. This is a must for tackling extreme mud conditions where you risk clogging your radiator and overheating your engine! Allows for easy servicing (cleaning) This is a factory OEM kit, not an aftermarket kit, instructions are provided on BRP’s website. Coolant overflow tank is included, hoses ect.. You will not find a better fit and finish kit on the market. There is drilling and cutting involved. This is all covered in great detail. Roughly 3.5 hour install time This kit fits G2 and G2L models check out the pictured fitment chart if you are unsure what you ride. The white “can-am” is a protective film that can be removed with a small pick. Part number 715001930
- SHIPS FREE TO THE LOWER 48 STATES Dash swap kit for G2 2012-17 Can-Am ATV’s. WILL NOT FUNCTION 100% on the L models 400/450/500/570 Please note some 2012-13 models may show "dps overheat" This is the factory gauge from the XT-P models. Dual Analog Style read outs. This has the built in coolant temperature gauge, a must for riding in extreme conditions! Brand new dash with 0 miles the Engine hours stay with the ecu, be sure to record your miles for your own records. Dash is set from the factory in KM/H and will require BUDS programming to change it to MPH This can be done at your local dealer or we offer this free of charge with purchase if you would like to stop by or you can send us your ecu, dash, key and DPS (power steering) if factory equipped. The dash is designed to auto pair, but sometimes it will not auto pair and you will have to program them together with buds software. This can be done at your local dealer or you can send in your ecu, key(s), and DPS (power steering) to us for programming. Part Number: 710005075 705006322
NEW Genuine OEM Can-am Rear Prop Shaft for 2012-14 Outlander 1000 NON XMR NON MAX Or 2012-18 Renegade 1000/1000R. NON XMR Comes with protector ring installed. Wear ring is not needed or included on this shaft. The yoke is simply machined larger in outer diameter. If you have any doubts about fitment, please count your splines on your gearbox output shaft and the pinion shaft on your differential. This shaft is for 20 spline gearbox output shaft and 18 spline rear differential. Current Part number: 703500991 Replaces Part Numbers: 703500929 703500862 705501413 705501258
- Dash/Speedometer for G2 500/650/800/1000 bikes. This is the factory Gauge/Screen. for 2014-18 G2 models. The dash is designed to auto pair, but sometimes it will not auto pair and you will have to program them together with buds software. This can be done at your local dealer or you can send in your ecu, key(s), and DPS (power steering) to us for programming. It will display 0 miles, please record your current miles for your records. Current Part Number 710003923 Replaces Part Number 710003454
- OUT OF STOCKDash/Speedometer for specific G2 500/650/800/1000R bikes. Please ask to confirm fitment if you are unsure, there are a few dashes that look the same. This is the factory Gauge/Screen for some 2018-20 G2 models. The dash is designed to auto pair, but sometimes it will not auto pair and you will have to program them together with buds software. This can be done at your local dealer or you can send in your ecu, key(s), and DPS (power steering) to us for programming. It will display 0 miles, please record your current miles for your records. Current Part Number 710005599
NEW OEM 450 and 570 Outlander keyed ignition switch, and matched keys Two position switch, non DESS Style. This is just on and off. No headlight control. Used on 2017 and newer G2L ATV’s Comes with main key and back up key These are not the electronic black keys, these are cut keys to match the ignition switch Part Number 710007864 replaces 710005153