20 Spline Yoke Fits: XMR 1000, Maverick and ’14 & newer Commander style Rear differentials. You will need a wear ring if you are using this on the differential side of the shaft. These yokes are made to very tight tolerances, if you are not careful when installing these you can damage the yoke or your pinion shaft. We recommend you take your time and clean the pinion gear before installing. —Great for custom applications— Uses Factory size U joint (398 at the auto parts store) Part numbers 715900271
- 20 Spline Yoke with Wear ring installed. Fits: XMR 1000, Maverick and '14&newer Commander style Rear differentials. These yokes are made to very tight tolerances, if you are not careful when installing these you can damage the yoke or your pinion shaft. We recommend you take your time and clean the pinion gear before installing. ---Great for custom applications--- Uses Factory size U joint (398 at the auto parts store) Part numbers 715900271 705400036
- New OEM 18 spline yoke with fully machined surface This is the forward most yoke on the rear driveshaft of G1 ATVs Fits years 2006 and newer, 450 and larger machines, if you are unsure on fitment please contact us. Use with 398 type U joints Current Part number 715900101 Replaces 705500371 705501372
- SHIPS FREE TO THE LOWER 48 STATES NEW OEM Canam Parts OEM 14% LOWER LOW GEAR SET for most every 1000 Vtwins minus north american 2015 and newer outlander 1000/1000R This is the way to reduce the over all Low Gear ratio on your can-am 1000 running larger tires. This is the LOW RATIO for any Large Gearbox. The last picture shows a Large gearbox. This will not fit Small Gearboxes. 14% lower gear ratio than standard 1000 gear boxes (Maverick, Commander, Renegade, Outlander) Will also fit 800 Commander
- NEW OEM Can-Am Variator CVT Clutch Outer Cover Belt Box This part is made for 2016-current Outlander and Renegade 1000R’s Perfect for a machine with a larger aftermarket clutch or any machine using a Maverick Primary with a stud/nut, as this cover has more room inside. **NOTE: This cover does not have any extra venting holes** Current Part number: 420612316 Old Part number: 420612310
- SHIPS FREE TO THE LOWER 48 STATES NEW OEM Canam Cam Chain and Guide Set for V Twin 1000 Order QTY 1 (one) per engine. Kit includes: 2 Silent Chains 420297068 2 Pivot Guides 420436017 2 Fixed Guides 420236583 2 Bottom Guides 420236350 ONLY WORKS WITH 1000 V TWINS To install the timing chain kit you will need to remove the PTO Cover, Stator Cover, and cylinder heads. We sell the gaskets and pullers required to do this. Check our other listings for these products
New NGK Spark Plug 93444
OEM part number 715900352
NGK part number LMAR8D-J
These spark plugs work in 2015+ Outlander/Renegade 450 850 and 1000R also fits Defender HD5
Shell
Thread Diameter: 10mm
Thread Pitch: 1.0mm
Seat Type: Gasket
Reach: 26.5mm (1.04″)
Hex Size: 9/16″ (14mm)
Terminal Type: Solid
Gap: .031″ (0.8mm)Center Electrode
Material: Nickel
Type: Standard
Size: 2.5mm
Projection: ProjectedGround Electrode
Material: Nickel
Type: Multi-GroundSpecifications
Resistor: Yes
Resistor Value: 5k Ohm
Heat Range: 8
Torque Specs: Aluminum: 7.2-8.7 lb. ft.- New NGK Spark Plug 90526 OEM part number 715900492 415130363 NGK part number LMAR9AI-8D These spark plugs work in 2017 Maverick X3 900 triple engines Thread Diameter 10mm Thread Pitch 1.0mm Seat Type Gasket Reach 26.5mm (1.04") Hex Size 9/16" (14mm) Terminal Type Solid Gap .031" (0.8mm) Center Electrode Material Iridium Type Fine Wire Size 0.6mm Projection Projected Ground Electrode Material Nickel Type Standard Shape Taper Cut Quantity 1 Resistor Value 5k Ohm Heat Range 9 Torque Specs Aluminum: 7.2-8.7 lb. ft.
- neapco Brand U joint for front drive shafts These U joints are made in Italy, please do not confuse these with the sub-grade china made u joints. Fits: G1 Renegade and Outlander . Also works on Outlander 400 Rear shafts. Maverick/Commander front driveshafts Will not fit: Maverick X3/Sport/Trail or Defender Includes clips, and grease fitting. Pro tip: Install grease fitting before pressing in u joint. Install u joint in a manner where you can still grease the joint in chassis. Replaces OEM : 715900325 703000023 703000024 703500002 703500135 703500607 703500814
- For use with all BRP turn key type ignition switches. Will not fit RFID type ignitions. Simply cut off the old harness and use the included butt connectors or solder the connections to the new pigtail. Be sure to match up one wire at a time when installing, this helps avoid switching wire orientation as the wires are not color coded. The wires are 6” long so it can be fixed inside the headlight pod Sold each; includes butt connectors and zip ties Part number 2120-0943