20 Spline Yoke Fits: XMR 1000, Maverick and ’14 & newer Commander style Rear differentials. You will need a wear ring if you are using this on the differential side of the shaft. These yokes are made to very tight tolerances, if you are not careful when installing these you can damage the yoke or your pinion shaft. We recommend you take your time and clean the pinion gear before installing. —Great for custom applications— Uses Factory size U joint (398 at the auto parts store) Part numbers 715900271
- Can Am Outlander Renegade Front U Joint These are found on the front prop shaft of G1 ATV’s and front drive shaft of Commander and Maverick (non X3/Sport/Trail) Also used on the 400 rear drive shaft 22mm caps. This is a new OEM part Replaces Part numbers: 703000023 703500814 703500607 703500135 703500002 703000024 715900183 715900325
- OUT OF STOCKNEW OEM G2 ATV Battery Hold Down Fixation Plate Kit. This retains the battery in place, and gives your seat something to latch into Kit includes: Fixation Plate 710009129 replaces 710002404 Positive Battery Terminal Cover 710006729 Rubber Stopper 705014429 Three aftermarket stainless bolts
- HD Clutch bolt set for most every Can-am V-twin 2006 to current. Will not work on: Maverick Turbo Maverick X3 Maverick Sport Maverick Trail Defender These will swap out the factory Torque To Yield (TTY) bolts/studs. M10 and M12 Black-Oxide Alloy Steel Socket Head Bolt These are class 12.9 bolts, with a tensile strength of 170,000 psi, these alloy steel bolts are stronger than Grade 8 steel bolts. 8 and 10mm Allen Sockets required to install these bolts. 18-8 Stainless Steel Single-Wave Washers included, these help prevent loosening, use with your existing washers. Installation Torque Specs: 80 ft·lb On the Primary Bolt 45 ft·lb On the Secondary Bolt (red thread locker recommended, allow to set up overnight)
- Please verify your differential uses this style of Seals before ordering! Can Am Standard Rear Differential Pinion and Axle Seals (Timken or SKF) Please measure your parts before ordering to verify fitment. The Pinion Seal has a 70mm Outer Diameter and the standard 37mm inner diameter. Replaces part number 705401481 The Axle Seal has a 52mm Outer Diameter And the standard 30mm inner diameter. Complete Seal kit for Standard Rear differentials common to find in 2016 and newer ATVs or if your differential has been repalced.
- NEW OEM BRP XPS DCT fluid 9779710 one quart 32oz dual clutch transmission synthetic oilThe best protection for the most demanding conditions, from low-end torque to high horsepower.Our most advanced formulation delivers even more peace of mind with superior performance and protection, thanks to increased shear resistance & detergency without compromising on volatility.SpecificationsExceptional oxidation stability and resistance to chemical deterioration — maintains long-lasting fluid quality and helps prolong transmission lifeExcellent lubricating characteristics for clutch friction durability, smooth shifting, and excellent wear protectionExcellent viscosity stability to help assure adequate lubrication and to maintain excellent viscosity properties at low start-up temperatures and high operating temperaturesDependable protection against rust and corrosionExcellent seal performance to protect against fluid leakage and prevent component failures from oil starvationFormulated especially for your side by side vehicle
- OUT OF STOCKCVTech Primary Clutch Holding tool. Very nice tool for torquing nut on the clutch or the bolt holding clutch on to the crankshaft taper. 0155-1018 Part number
- NEW OEM Winch Switch 710002052 New Genuine OEM Can-Am 4 Wheel Drive Switch This operates the winch on your SXS This is a two position momentary rocker switch. Fits: Commander, Maverick and Maverick Turbo, Maverick X3, Maverick Sport, Defender If you aren’t sure if this will fit, please ask, we will help! Part number 710002052
- New OEM 18 spline yoke with fully machined surface This is the forward most yoke on the rear driveshaft of G1 ATVs Fits years 2006 and newer, 450 and larger machines, if you are unsure on fitment please contact us. Use with 398 type U joints Current Part number 715900101 Replaces 705500371 705501372
- Air Filter for G1 Outlander and Renegades. Replaces OEM 707800174 Fits 500, 650, and 800HO NON-R 800 engines, from 2006 – 2012. Bonded, two-layer .65" foam designed for maximum protection and airflow Coarse outer foam traps large particles while fine inner foam catches the finest dust With the precision pre-oiled air filter, there is no excess oil to rob horsepower, and no dry spots endangering your engine Made in the U.S.A.
- EPI Ball Joint Kit G1 Fits Outlander 650/800 Upper Renegade 500/800 Lower or Upper Heavy Duty Steel housing with isolated design joint for long life Ball joint includes ball joint, rubber boot, snap ring and cotter pin EPI Part Number: WE351039 P/U Part Number: 0430-0610 Replaces OEM Part Number: 706200653
- Can-am Rubber Trailing Arm cover and Oetiker clamp for your G1 Outlander or Renegade Will only work on the gen 1 Outlander and Renegades 2006-11 and some 2012 models. If you are unsure on fitment, please ask. You will need to order qty 2 to replace both sides. Genuine OEM parts Part Numbers: 706000222 706000749 293650162
- OUT OF STOCKNEW Genuine OEM Fuel/Gas Cap Fits most every Can-am ATV Renegade or Outlander Part Number: 513033025
- Moose Racing Air Filter Part Number 1011-2796 Fits SXS pictured: Commanders 800/1000 and Maverick 1000R (non turbo) (non X3/Sport/Trail) Engineered for maximum air flow, increasing horsepower Maintains premium protection by stopping the finest dust particles Flexible seams that will not crack Filters are designed to fit all stock air boxes Made in the U.S.A. Replaces OEM 707800327