CVTech Primary Clutch Holding tool. Very nice tool for torquing nut on the clutch or the bolt holding clutch on to the crankshaft taper. 0155-1018 Part number
NEW OEM BRP XPS DCT fluid 9779710 one quart 32oz dual clutch transmission synthetic oilThe best protection for the most demanding conditions, from low-end torque to high horsepower.Our most advanced formulation delivers even more peace of mind with superior performance and protection, thanks to increased shear resistance & detergency without compromising on volatility.SpecificationsExceptional oxidation stability and resistance to chemical deterioration — maintains long-lasting fluid quality and helps prolong transmission lifeExcellent lubricating characteristics for clutch friction durability, smooth shifting, and excellent wear protectionExcellent viscosity stability to help assure adequate lubrication and to maintain excellent viscosity properties at low start-up temperatures and high operating temperaturesDependable protection against rust and corrosionExcellent seal performance to protect against fluid leakage and prevent component failures from oil starvationFormulated especially for your side by side vehicle
Please verify your differential uses this style of Seals before ordering! Can Am Standard Rear Differential Pinion and Axle Seals (Timken or SKF) Please measure your parts before ordering to verify fitment. The Pinion Seal has a 70mm Outer Diameter and the standard 37mm inner diameter. Replaces part number 705401481 The Axle Seal has a 52mm Outer Diameter And the standard 30mm inner diameter. Complete Seal kit for Standard Rear differentials common to find in 2016 and newer ATVs or if your differential has been repalced.
New short wiring harness for rear tail lights Will need to be wired in to work. This plugs in to Tail light part number 710001645 Fits: G2 ATV's with dual tail lights, Commanders, and Mavericks (non X3/Sport/Trail)
HD Clutch bolt set for most every Can-am V-twin 2006 to current. Will not work on: Maverick Turbo Maverick X3 Maverick Sport Maverick Trail Defender These will swap out the factory Torque To Yield (TTY) bolts/studs. M10 and M12 Black-Oxide Alloy Steel Socket Head Bolt These are class 12.9 bolts, with a tensile strength of 170,000 psi, these alloy steel bolts are stronger than Grade 8 steel bolts. 8 and 10mm Allen Sockets required to install these bolts. 18-8 Stainless Steel Single-Wave Washers included, these help prevent loosening, use with your existing washers. Installation Torque Specs: 80 ft·lb On the Primary Bolt 45 ft·lb On the Secondary Bolt (red thread locker recommended, allow to set up overnight)
NEW MRRPM Upper Motor Mount for installing 'big block" 1000 engines into a G1 chassis Steel, black in color
Replaces OEM part number 420222691 Upgrade your plastic thermostat housings/water neck on your vtwin 500/570/650/800/850/1000 SOLD AS PAIR These will work in Commanders, Mavericks, Outlanders & Renegades
Used- Good Condition OEM Can-Am Grab Handle for Commander & Maverick Product Number: 705203332 Comes as Pictured- OUT OF STOCK
NEW OEM G2 ATV Battery Hold Down Fixation Plate Kit. This retains the battery in place, and gives your seat something to latch into Kit includes: Fixation Plate 710009129 replaces 710002404 Positive Battery Terminal Cover 710006729 Rubber Stopper 705014429 Three aftermarket stainless bolts 
New All Balls Racing Engine Air Filter Part number 48-1012 10 inches tall 5 inch diameter Replaces OEM 715900394 Fits 2016-Current Defenders HD5, HD8, and HD10's both 3 and 6 seat machines Fits 2018-Current Maverick Trail 800 and 1000 Fits 2019-Current Maverick Sport 1000
Can Am Outlander Renegade Front U Joint These are found on the front prop shaft of G1 ATV’s and front drive shaft of Commander and Maverick (non X3/Sport/Trail) Also used on the 400 rear drive shaft 22mm caps. This is a new OEM part Replaces Part numbers: 703000023 703500814 703500607 703500135 703500002 703000024 715900183 715900325
20 Spline Yoke Fits: XMR 1000, Maverick and ’14 & newer Commander style Rear differentials. You will need a wear ring if you are using this on the differential side of the shaft. These yokes are made to very tight tolerances, if you are not careful when installing these you can damage the yoke or your pinion shaft. We recommend you take your time and clean the pinion gear before installing. —Great for custom applications— Uses Factory size U joint (398 at the auto parts store) Part numbers 715900271
Have Questions?
Our staff is available to answer questions
canampartsguy@gmail.com
1340 Okray Ave.
Plover, WI 54467
jared@canampartsguy.com
Cant find What you're looking for?
Visit our 
store!
2016 Can Am Parts, LLC. All rights reserved.