OEM Canam Insert, this holds cab interior panels together in your maverick or commander. Part Numbers: 707900133 503189273
Can-am Style Plastic Fender rivet set. NEW Pack of 25 For 8mm (5/16?) holes great for holding plastic fenders together, works on Maverick, Commander, Outlander and Renegade Replaces part numbers 293150089 293150230
OEM Can Am wheel bearing. Double row ball bearing.
Fits G1 and G2 Outlander and Renegade.
Fits Commander and Maverick.
WILL NOT work with the Maverick X3 .Current Part number 293350150
Replaces: 293350118 705400088 and 293350040Unsure on fitment?
Here are the dimensions:
30mm Inner Diameter
60mm Outer Diameter
37mm WideWill come as pictured
HD Clutch bolt set for most every Can-am V-twin 2006 to current. Will not work on: Maverick Turbo Maverick X3 Maverick Sport Maverick Trail Defender These will swap out the factory Torque To Yield (TTY) bolts/studs. M10 and M12 Black-Oxide Alloy Steel Socket Head Bolt These are class 12.9 bolts, with a tensile strength of 170,000 psi, these alloy steel bolts are stronger than Grade 8 steel bolts. 8 and 10mm Allen Sockets required to install these bolts. 18-8 Stainless Steel Single-Wave Washers included, these help prevent loosening, use with your existing washers. Installation Torque Specs: 80 ft·lb On the Primary Bolt 45 ft·lb On the Secondary Bolt (red thread locker recommended, allow to set up overnight)
OEM Canam Insert, this holds cab interior panels together in your maverick or commander.
Part Number: 707900133
Replaces OEM part number 420222691 Upgrade your plastic thermostat housings/water neck on your vtwin 500/570/650/800/850/1000 SOLD AS PAIR These will work in Commanders, Mavericks, Outlanders & Renegades
NEW OEM Can-am rear driveshaft retaining bolts. Don’t know your size? These are the two most common sizes. M12 x 16 and M10 x 16 with washers. Ships exactly as pictured. On the M12x16 bolt we recommend adding thread locking compound before installation. Thread pitch is 1.25
Fits G2 ATV’s Outlander or Renegade 500 450 570 650 800 850 1000 1000R
Shift Arm Base Upgrade
Replaces OEM 707003054 707000971 707002439
USA made Made from 6061 T6 Aluminum (aircraft grade)
This plate does not require any additional hardware, use a zip tie to retain the wire harness or vent lines running near it.
NEW Prop Shaft Low profile pair of clamps for 715900118 boot. Clamps also work for G2 front shaft boot 705401093. The last few pictures show the clamps loose, then installed nice and tight. Sold in pairs enough to do one boot.
Cast Aluminum Valve cover set with Stainless bolts. Replaces your factory plastic valve covers on any can-am V-twin ATV or UTV If you have aftermarket camshafts you may need to clearance the cover with a dremel. 500/570/650/800/850/1000/1000R Replaces OE Numbers: 420610390 420610394 420610393 420610395
Single CVT cover bolt with the hex head and torx inside. The preferred style to work with. Part number 420440568 replaces 420440567 420440307 Genuine OEM Part A little anti-seize is a great idea when installing these bolts, as the inserts they screw into can easily strip out.
M8x1.25×70 Bolt. m8-1.25x70mm Used to open the secondary clutch on many Can-am ATV’s & SXS’s Simple tool, trusted seller. Or just use these specs and head to your hardware store.
Brand New Genuine OEM Wear ring a must if you are replacing your pinion seal, these are the sacrificial parts that save your drive shaft from grooving! Will fit 18 and 20 Spline Yokes that are fully machined Part Number 705400036
420927837 Thermostat Gasket Sold Each, vtwin’s require two per engine.
Rear driveshaft U-Joint Replacement 398 style Fits all V-twin Canam rear driveshafts XMR XT XXC XDS XRS STD Grease zerk in cap for easy maintenance Made in Japan High Quality Clips are included just as pictured We recommend pumping fresh grease in after installing, as the grease inside may not be enough for operation. Please note on some older driveshafts the yoke ears may need to be ground down to allow for the larger center part of the joint to be installed. Replaces OEM part numbers: 703500846 715900270 715900278
New Vertex Valve cover gasket Fits canam vtwin engines 500 and larger Order two per engine Part number 817989 replaces OEM 420630262 420630260
Can Am XPS premium coolant extended life premixed do not add water Extended Life Premixed Antifreeze/Coolant provides extended protection against rust corrosion and pitting caused by cavitation for all coolant system metals including aluminum. It provides protection against radiator freeze-up down to -37*C (-34.6*F) and boil over to 129*C (264.2*F) with a 100 kilopascal (15psi) radiator cap in good working condition. This is orange in color 1 U.S. quart (32 fl. oz) 946 ml Part Number: 779150- Sale!
This is a brand new OEM Maverick Belt This is the correct belt for the 2013-18 "OG" Maverick 1000R turbo or non turbo WILL NOT FIT X3, sport or trail Maverick models. This will fit all VTWIN 500, 570, 650, 800, 800R, 850, 1000, 1000R Outlander or Renegade This will fit 2011-2020 Commander 800R, 1000, and 1000R WILL NOT FIT 2021+ Commander ? This is the strongest belt for the Can-am Vtwins on the market. We recommend this belt if you have over sized tires or use your machine in extreme conditions. OLD Part Numbers 715900212 422280364 NEW Part Number 422280367 WILL NOT FIT X3, sport or trail Maverick models. WILL NOT FIT 2021+ Commander 
Brand New Genuine OEM Valve Cover Gasket. Will work on most Can Am engines from 2003 through current, front or back cylinder. Part number 420630260 replaces 420630262
New OEM Can-am Part This boot fits the G2 outlander/renegade front driveshaft. It is the thicker tapered boot, some use two of these on G2 atv's front driveshaft. Part number 705401093
Can-am OEM tool. High-quality, heat-treated steel for superior strength. A tool needed to pull primary clutches off the crank shaft taper. Part Number: 529035746
Brand new Genuine OEM flexible CVT intake adaptor for Renegade, Outlander, Maverick, and Commander.
This replaces the thin rubber boot that comes on many early CanAm V-Twin models.
Very nice upgrade for a cracked CVT intake boot.
Current part number 707002585
Previous part numbers 707001467, 707001043, 707000719
New Aftermarket Bellows with clamp, use this in place of vent lines on your differentials. Replaces OEM part number: 705400352
Brand New Genuine OEM Fill Level Plug Be sure that yours looks the same due to other styles for front or rear differential from different years M14 diameter 1.5 thread pitch Part number 705500504
Have Questions?
Our staff is available to answer questions
canampartsguy@gmail.com
1340 Okray Ave.
Plover, WI 54467
jared@canampartsguy.com
Cant find What you're looking for?
Visit our 
store!
2016 Can Am Parts, LLC. All rights reserved.