OEM Can Am wheel bearing. Double row ball bearing.
Fits G1 and G2 Outlander and Renegade.
Fits Commander and Maverick.
WILL NOT work with the Maverick X3 .Current Part number 293350150
Replaces: 293350118 705400088 and 293350040Unsure on fitment?
Here are the dimensions:
30mm Inner Diameter
60mm Outer Diameter
37mm WideWill come as pictured
- HD Clutch bolt set for most every Can-am V-twin 2006 to current. Will not work on: Maverick Turbo Maverick X3 Maverick Sport Maverick Trail Defender These will swap out the factory Torque To Yield (TTY) bolts/studs. M10 and M12 Black-Oxide Alloy Steel Socket Head Bolt These are class 12.9 bolts, with a tensile strength of 170,000 psi, these alloy steel bolts are stronger than Grade 8 steel bolts. 8 and 10mm Allen Sockets required to install these bolts. 18-8 Stainless Steel Single-Wave Washers included, these help prevent loosening, use with your existing washers. Installation Torque Specs: 80 ft·lb On the Primary Bolt 45 ft·lb On the Secondary Bolt (red thread locker recommended, allow to set up overnight)
Fits G2 ATV’s Outlander or Renegade 500 450 570 650 800 850 1000 1000R
Shift Arm Base Upgrade
Replaces OEM 707003054 707000971 707002439
USA made Made from 6061 T6 Aluminum (aircraft grade)
This plate does not require any additional hardware, use a zip tie to retain the wire harness or vent lines running near it.
- Cast Aluminum Valve cover set with Stainless bolts. Replaces your factory plastic valve covers on any can-am V-twin ATV or UTV If you have aftermarket camshafts you may need to clearance the cover with a dremel. 500/570/650/800/850/1000/1000R Replaces OE Numbers: 420610390 420610394 420610393 420610395
- Rear driveshaft U-Joint Replacement 398 style Fits all V-twin Canam rear driveshafts XMR XT XXC XDS XRS STD Grease zerk in cap for easy maintenance Made in Japan High Quality Clips are included just as pictured We recommend pumping fresh grease in after installing, as the grease inside may not be enough for operation. Please note on some older driveshafts the yoke ears may need to be ground down to allow for the larger center part of the joint to be installed. Replaces OEM part numbers: 703500846 715900270 715900278
- Sale!This is a brand new OEM Maverick Belt This is the correct belt for the 2013-18 "OG" Maverick 1000R turbo or non turbo WILL NOT FIT X3, sport or trail Maverick models. This will fit all VTWIN 500, 570, 650, 800, 800R, 850, 1000, 1000R Outlander or Renegade This will fit 2011-2020 Commander 800R, 1000, and 1000R WILL NOT FIT 2021+ Commander ? This is the strongest belt for the Can-am Vtwins on the market. We recommend this belt if you have over sized tires or use your machine in extreme conditions. OLD Part Numbers 715900212 422280364 NEW Part Number 422280367 WILL NOT FIT X3, sport or trail Maverick models. WILL NOT FIT 2021+ Commander
- Can Am XPS premium coolant extended life premixed do not add water Extended Life Premixed Antifreeze/Coolant provides extended protection against rust corrosion and pitting caused by cavitation for all coolant system metals including aluminum. It provides protection against radiator freeze-up down to -37*C (-34.6*F) and boil over to 129*C (264.2*F) with a 100 kilopascal (15psi) radiator cap in good working condition. This is orange in color 1 U.S. quart (32 fl. oz) 946 ml Part Number: 779150
- OUT OF STOCKNew OEM Can-am Part This boot fits the G2 outlander/renegade front driveshaft. It is the thicker tapered boot, some use two of these on G2 atv's front driveshaft. Part number 705401093
Brand new Genuine OEM flexible CVT intake adaptor for Renegade, Outlander, Maverick, and Commander.
This replaces the thin rubber boot that comes on many early CanAm V-Twin models.
Very nice upgrade for a cracked CVT intake boot.
Current part number 707002585
Previous part numbers 707001467, 707001043, 707000719
Rear Differential Seal kit for differentials with 80mm outer diameter pinion seal
1 Pinion Seal, 80mm
2 Axle Seals, 52mmBrands we use include : Timken, Dichtomatik and SKF
Fits:
2013 to Current Outlander 1000/1000R XMR
2015 to Current Outlander 800/850 Xmr
2016 to Current Renegade 1000R XMR
2019 to Current 650 and Larger ATVs
Also some 2019 to Current 570 XMR (measure your parts to verify fitment)*** THIS WILL NOT WORK IN 2013-2018 650/570 XMR or 2011/2012 800 XMR machines. If you are unsure about fitment please contact us! ***
- Please verify your differential uses this style of Seals before ordering! Can Am Front Differential Pinion and Axle Seals (Timken) Fit on most all 2006-2019 Outlanders and Renegades Also fits Commanders and Mavericks (non X3/Sport/Trail) The Pinion Seal has a 70mm Outer Diameter And the standard 37mm inner diameter. Replaces part numbers 705401481 705500255 705500081 The Axle Seal has a 47mm Outer Diameter And the standard 25mm inner diameter. Replaces part numbers 705401618 705401486 Complete Seal kit for Standard Front Differentials
Can-am Outlander, Renegade or Commander 500 650 800 1000 6 Bolt HD rear Differential.
This is an OEM Canam part used in many Generation 2 atvs.
It does not have the bracket for the rear brake caliper on it.
This is an updated version with much more substantial webbing for improved support.
Fits:
2012 Outlander and Renegade 800, 1000
2013 to 2018 500/570/650/800/1000 Outlander Renegade
2011-2013 Commander 800 1000
2013-2018 XMR 570 and 650**WILL NOT FIT** XMR 1000 or XMR 800
WILL NOT FIT ALL 2019 Models, please contact us if you have a 2019.Current Part Number 703501019
Previous Part Numbers 703500878, 705501896, 705501419, 705501993Brand New Genuine OEM Can-am Inner Cover Air Guide Clutch backing plate, this is the part that is against the engine and gearbox on most every can-am v twin. 13 Bolt design allows for better sealing We recommend adding anti seize thread lubricant when installing your cvt cover bolts. Old Part Number 420611409, 420611408 Current Part Number 420612304
- SHIPS FREE TO THE LOWER 48 STATES NEW OEM Can Am Updated Cam Chain and Updated Guide Set 2006-Current V Twins 500, 570, 650, 800 These chains and guides are a common issue on 2006-2008 500/650/800 V-twin ATV’s. The chains fail and start cutting the plastic guides. One of two things happen: One, the Camshaft (generally the front cylinder head, first) becomes out of time, and the valves hit the piston. Two, the oil pick up screen becomes clogged with guide material. Engine oil can not be cycled through the engine, generally this spins the big end connecting rod bearings. This kit includes updated chains and guides, totally avoiding this problem. Order QTY 1 (one) per engine. Kit includes: 2 Chains 420297063 2 pivot guides 420436015 2 fixed guides 420236584 2 bottom guides 420236351 Will not work on 1000/1000R Engines To install the timing chain kit you will need to remove the PTO Cover, Stator Cover, and Cylinder Heads. We sell the gaskets and pullers required to do this. Check our other listings for these products