HD Clutch bolt set for most every Can-am V-twin 2006 to current. Will not work on: Maverick Turbo Maverick X3 Maverick Sport Maverick Trail Defender These will swap out the factory Torque To Yield (TTY) bolts/studs. M10 and M12 Black-Oxide Alloy Steel Socket Head Bolt These are class 12.9 bolts, with a tensile strength of 170,000 psi, these alloy steel bolts are stronger than Grade 8 steel bolts. 8 and 10mm Allen Sockets required to install these bolts. 18-8 Stainless Steel Single-Wave Washers included, these help prevent loosening, use with your existing washers. Installation Torque Specs: 80 ft·lb On the Primary Bolt 45 ft·lb On the Secondary Bolt (red thread locker recommended, allow to set up overnight)
New short wiring harness for rear tail lights Will need to be wired in to work. This plugs in to Tail light part number 710001645 Fits: G2 ATV's with dual tail lights, Commanders, and Mavericks (non X3/Sport/Trail)
Please verify your differential uses this style of Seals before ordering! Can Am Standard Rear Differential Pinion and Axle Seals (Timken or SKF) Please measure your parts before ordering to verify fitment. The Pinion Seal has a 70mm Outer Diameter and the standard 37mm inner diameter. Replaces part number 705401481 The Axle Seal has a 52mm Outer Diameter And the standard 30mm inner diameter. Complete Seal kit for Standard Rear differentials common to find in 2016 and newer ATVs or if your differential has been repalced.- OUT OF STOCK
CVTech Primary Clutch Holding tool. Very nice tool for torquing nut on the clutch or the bolt holding clutch on to the crankshaft taper. 0155-1018 Part number 
Plain bearing half 40 X 43 X 15 This fits into one side of the connecting rod. part number 420233980
Brand New Moose Utility 13 Bolt CVT Cover Gasket
Works on 7 bolt covers also.
Part number 0935-1193
replaces: 420430127 420430126 420430124 420430123 420430120
New OEM 18 spline yoke with fully machined surface This is the forward most yoke on the rear driveshaft of G1 ATVs Fits years 2006 and newer, 450 and larger machines, if you are unsure on fitment please contact us. Use with 398 type U joints Current Part number 715900101 Replaces 705500371 705501372
Air Filter for G1 Outlander and Renegades. Replaces OEM 707800174 Fits 500, 650, and 800HO NON-R 800 engines, from 2006 – 2012. Bonded, two-layer .65" foam designed for maximum protection and airflow Coarse outer foam traps large particles while fine inner foam catches the finest dust With the precision pre-oiled air filter, there is no excess oil to rob horsepower, and no dry spots endangering your engine Made in the U.S.A.
EPI Ball Joint Kit G1 Fits Outlander 650/800 Upper Renegade 500/800 Lower or Upper Heavy Duty Steel housing with isolated design joint for long life Ball joint includes ball joint, rubber boot, snap ring and cotter pin EPI Part Number: WE351039 P/U Part Number: 0430-0610 Replaces OEM Part Number: 706200653
Brand New OEM PTO Cover Gasket for V-Twin Engines Part number 420651211
Can-am Rubber Trailing Arm cover and Oetiker clamp for your G1 Outlander or Renegade Will only work on the gen 1 Outlander and Renegades 2006-11 and some 2012 models. If you are unsure on fitment, please ask. You will need to order qty 2 to replace both sides. Genuine OEM parts Part Numbers: 706000222 706000749 293650162- OUT OF STOCK
Brand New Genuine OEM Wear ring a must if you are replacing your pinion seal, these are the sacrificial parts that save your drive shaft from grooving! Will fit 18 and 20 Spline Yokes that are fully machined Part Number 705400036 
G2 ATV brake caliper seal kit 21-83170 These fit G2 ATV brake calipers, if you have fitment questions please reach out, we are here to help- OUT OF STOCK
NEW Genuine OEM Fuel/Gas Cap Fits most every Can-am ATV Renegade or Outlander Part Number: 513033025 
NEW OEM Can-am Output Crank Shaft Seal This is the engine out put shaft seal, pressed into the crankcase PTO cover 34mm Inner Diameter 52mm Outer Diameter 8mm Thick Current Part Number 420631933 Replaces Part Number 420631932
NEW OEM 20 spline yoke. This fits on large gearboxes output shafts. 20 spline yoke partially machined to accept a protector ring. This is the forward most yoke on the REAR driveshaft. Works with 398 U joints. found on Vtwin rear driveshafts. Part number 715900129 replaces 705501373 and 715900234
NEW OEM Can-am rear driveshaft retaining bolts. Don’t know your size? These are the two most common sizes. M12 x 16 and M10 x 16 with washers. Ships exactly as pictured. On the M12x16 bolt we recommend adding thread locking compound before installation. Thread pitch is 1.25
New OEM Differential Pinion Seal. Please check your wear ring, if that is grooved it is time to replace. Very easy to miss that and blame a new seal on a bad wear ring. Will fit: Gen 1 Front and Rear Diffs Gen 2 Outlander and Renegade Front and Rear Early Commander Rear All Maverick and Commander Front WILL NOT FIT G2 XMR 800/850/1000 REAR DIFFERENTIAL Measurements are shown: 70mm outside and 37mm inside Part number 705401481- OUT OF STOCK
NEW Quad Logic Brand G2 ATV Can Am Airbox Seal Part number 500-1139-PU This is an improved design over factory Apply a small amount of grease to aid install, this is much thicker and denser than the OEM o-ring or gasket Replaces OEM part numbers: 293300165 293300175 293300179 
New Air filter made by All Balls Racing. This is an OEM replacement filter for early G1 500 650 800HO Outlander or Renegade Please note this will not fit the 800R ATVs Replaces OEM 707800174
NEW OEM Can Am Tool M8x1.25 Tapered Bolt Part number 529036098. This tool fills a few roles, used to open the secondary clutch on many models. This will also lock the crankshaft on Vtwin's and three cylinder models. If you are unsure on application please reach out to us, we are here to help!
SP1 Radiator Relocation Kit Replacement Latch Kit. Replaces OEM 860200239 517303981 517304075 Kit includes 2 Latches. Enough to retain one radiator access panel.
New Oem Canam Pinion nut, this is spun on to the pinion gear to retain the bearings on the pinion gear of xmr differentials on ATV XMR's G2 800/850/1000/1000R This is not needed on 570 or 650 XMR models The threads are M28x1.25 Right Hand the outer diameter is 51mm Please check that this is the correct nut for your application Part number 705501550
Can Am 2016+ Renegade XMR Prefilter Screen This is a OEM prefilter Part # 705010922
NEW EPI Performance Fuel/Gas Cap EPIGC6 Replaces OEM part numbers 572039600 513033025
New NGK Spark Plug 93444
OEM part number 715900352
NGK part number LMAR8D-J
These spark plugs work in 2015+ Outlander/Renegade 450 850 and 1000R also fits Defender HD5
Shell
Thread Diameter: 10mm
Thread Pitch: 1.0mm
Seat Type: Gasket
Reach: 26.5mm (1.04″)
Hex Size: 9/16″ (14mm)
Terminal Type: Solid
Gap: .031″ (0.8mm)Center Electrode
Material: Nickel
Type: Standard
Size: 2.5mm
Projection: ProjectedGround Electrode
Material: Nickel
Type: Multi-GroundSpecifications
Resistor: Yes
Resistor Value: 5k Ohm
Heat Range: 8
Torque Specs: Aluminum: 7.2-8.7 lb. ft.
NEW OEM Idle Gear Oil Seal Part number 420430555
NEW OEM Speedometer trim found on Renegade XMR models. Part number 705015189
NEW OEM Exhaust Muffler Gasket This slides on to the header pipe, then muffler slides over it. 2" outer diameter 1.77" inner diameter 1" wide Part number 707600430
New OEM can-am input or output seal for small gear boxes You will need two per gearbox. 32mm inner diameter 47mm outer diameter 7mm thick Current Part Number 420950089 Replaces Part Number 420950087
Gearbox Shift Shaft Seal 28mm OD 12mm ID 7mm Thick Part numbers: 711250450 420250450
New IKO, Koyo or NTN brand needle bearing B98 replaces 705500261 If you are unsure on fitment please reach out to us we will help.- OUT OF STOCK
Moose Racing Radiator Cap Fits Outlander, Renegade, Commander, Defender and Maverick Unsure on fitment, please ask us. Cap is set to the same 15.9PSI as stock. If you current cap is not holding pressure replacing with new will help avoid overheating. Replaces OEM 709200207 709200033 
New electrical connector cap, this covers the 8 pin open connector found on US models. This cap seals and helps keep your open harness plug free from dirt and corrosion. Be sure to clean out the connection before installing, dielectric grease is a great idea for extra protection. OEM supplier brand housing Aptiv formally Delphi
This model type is a rubber O.D. seal with two sealing lips. The main sealing lip is spring loaded. This is a two-way seal, which means that it can retain lubricant and exclude contaminants simultaneously Canam Vtwin crankshaft main seal. Replaces OEM number 420631933 This seal is pressed into the PTO cover on v-twin's Unsure on fitment? Just measure you seal. 52mm Outer Diameter 34mm Inner Diameter 8mm Thick- Sale!
New take off gearbox side, 20 spline yoke. This fits on large gearboxes output shafts. 20 spline yoke partially machined to accept a protector ring. This is the forward most yoke on the REAR driveshaft. Works with 398 U joints. found on Vtwin rear driveshafts. Part number 715900129 replaces 705501373 and 715900234
Have Questions?
Our staff is available to answer questions
canampartsguy@gmail.com
1340 Okray Ave.
Plover, WI 54467
jared@canampartsguy.com
Cant find What you're looking for?
Visit our 
store!
2016 Can Am Parts, LLC. All rights reserved.