- OUT OF STOCK
NEW Quad Logic Brand G2 ATV Can Am Airbox Seal Part number 500-1139-PU This is an improved design over factory Apply a small amount of grease to aid install, this is much thicker and denser than the OEM o-ring or gasket Replaces OEM part numbers: 293300165 293300175 293300179 
New OEM Differential Pinion Seal. Please check your wear ring, if that is grooved it is time to replace. Very easy to miss that and blame a new seal on a bad wear ring. Will fit: Gen 1 Front and Rear Diffs Gen 2 Outlander and Renegade Front and Rear Early Commander Rear All Maverick and Commander Front WILL NOT FIT G2 XMR 800/850/1000 REAR DIFFERENTIAL Measurements are shown: 70mm outside and 37mm inside Part number 705401481
NEW OEM Can-am rear driveshaft retaining bolts. Don’t know your size? These are the two most common sizes. M12 x 16 and M10 x 16 with washers. Ships exactly as pictured. On the M12x16 bolt we recommend adding thread locking compound before installation. Thread pitch is 1.25
NEW OEM 20 spline yoke. This fits on large gearboxes output shafts. 20 spline yoke partially machined to accept a protector ring. This is the forward most yoke on the REAR driveshaft. Works with 398 U joints. found on Vtwin rear driveshafts. Part number 715900129 replaces 705501373 and 715900234
NEW OEM Can-am Output Crank Shaft Seal This is the engine out put shaft seal, pressed into the crankcase PTO cover 34mm Inner Diameter 52mm Outer Diameter 8mm Thick Current Part Number 420631933 Replaces Part Number 420631932- OUT OF STOCK
NEW Genuine OEM Fuel/Gas Cap Fits most every Can-am ATV Renegade or Outlander Part Number: 513033025 
G2 ATV brake caliper seal kit 21-83170 These fit G2 ATV brake calipers, if you have fitment questions please reach out, we are here to help
Brand New Genuine OEM Wear ring a must if you are replacing your pinion seal, these are the sacrificial parts that save your drive shaft from grooving! Will fit 18 and 20 Spline Yokes that are fully machined Part Number 705400036
Can-am Rubber Trailing Arm cover and Oetiker clamp for your G1 Outlander or Renegade Will only work on the gen 1 Outlander and Renegades 2006-11 and some 2012 models. If you are unsure on fitment, please ask. You will need to order qty 2 to replace both sides. Genuine OEM parts Part Numbers: 706000222 706000749 293650162
Brand New OEM PTO Cover Gasket for V-Twin Engines Part number 420651211
EPI Ball Joint Kit G1 Fits Outlander 650/800 Upper Renegade 500/800 Lower or Upper Heavy Duty Steel housing with isolated design joint for long life Ball joint includes ball joint, rubber boot, snap ring and cotter pin EPI Part Number: WE351039 P/U Part Number: 0430-0610 Replaces OEM Part Number: 706200653
Air Filter for G1 Outlander and Renegades. Replaces OEM 707800174 Fits 500, 650, and 800HO NON-R 800 engines, from 2006 – 2012. Bonded, two-layer .65" foam designed for maximum protection and airflow Coarse outer foam traps large particles while fine inner foam catches the finest dust With the precision pre-oiled air filter, there is no excess oil to rob horsepower, and no dry spots endangering your engine Made in the U.S.A.
Have Questions?
Our staff is available to answer questions
canampartsguy@gmail.com
1340 Okray Ave.
Plover, WI 54467
jared@canampartsguy.com
Cant find What you're looking for?
Visit our 
store!
2016 Can Am Parts, LLC. All rights reserved.