- NEW Chrome Conical Taper M10 Lug Nut Set of 16 M10x1.25 thread size 60 Degree taper 14mm Hex head size, great for use with aftermarket wheels where socket space is a concern These will work on every Canam ATV since 2006 and most every Canam sxs Will not fit the Maverick X3 12mm wheel studs. Part numbers: 57-94121, ALUG14BX
- BOYESEN SUPERCOOLER WATER PUMP Cover and Impeller Kit Increased coolant flow at all rpm ranges Patented Nautilus-style impeller for hydrodynamic efficiency Color/Finish: Black, Powder-Coated Material: Aluminum Model: Supercooler Part number 850709 WPK-80AB Replaces OEM 420822750, 420622020 and 420622022 This is the style with the larger output nipple roughly 1 inch in outer diameter.
There are a few options for kits, please verify your differential uses this style of gears before ordering!
This will only fit six mounting hole differentials.
Late G1 Early G2 Standard Rear Differential Ring 36t and Pinion 10t gear set Pinion bolt size is M10, this may be different than what you are replacing.
OEM Rear Differential Gear set 10/36 Ring and Pinion gear set. The gears are straight cut as pictured. This kit should be installed by an experienced technician.
Open up the differential! Check for two bearings total (one on each side) on the ring gear. If you only have two proceed to the next measurement. Measure your outer diameter of your axle seals! They should measure close to 1 3/4? (47mm) To further verify fitment you can measure your pinion pilot shaft, this should be 9/16″ (14mm) The pictures show this very clearly. Please take the time to measure your parts before buying this will save time and restocking fees.
- Air Filter for G1 Outlander and Renegades. Replaces OEM 707800174 Fits 500, 650, and 800HO NON-R 800 engines, from 2006 – 2012. Bonded, two-layer .65" foam designed for maximum protection and airflow Coarse outer foam traps large particles while fine inner foam catches the finest dust With the precision pre-oiled air filter, there is no excess oil to rob horsepower, and no dry spots endangering your engine Made in the U.S.A.
- For use with all BRP turn key type ignition switches. Will not fit RFID type ignitions. Simply cut off the old harness and use the included butt connectors or solder the connections to the new pigtail. Be sure to match up one wire at a time when installing, this helps avoid switching wire orientation as the wires are not color coded. The wires are 6” long so it can be fixed inside the headlight pod Sold each; includes butt connectors and zip ties Part number 2120-0943
NEW OEM Shock Heat Shield
This helps keep heat from the exhaust melting your bump stop in your shock.
Current part number 705210324 replaces 705209688
ATVs equipped with piggy-back reservoir type shocks will need to cut the bracket to clear the shock. These are made for use with the standard black bodied shocks.- New Demon Heavy Duty Axle Front Left Fits: G2 2012-2018 ATV Outlander/Renegade 500 570 650 800R 850 1000 1000R Part number PAXL-3070HD Replaces OEM 705400756 703500823 705401943 705401115 705401384 705401947 705401704 Through years of research and development Demon Powersports has developed an axle that doesn’t burn a hole in your pocket and adheres to the highest quality standards. These axles are bigger, beefier, and stronger. Demon Heavy Duty Axles are built using larger CV joints and shafts, paired with our proprietary dual heat treatment process, and 4340 Chromoly Steel inner CV cage gives these the axles the edge it needs for superior strength and longevity. These axles also utilize a unique double plunge design which allows it to achieve higher articulation angles approximately, the axles are designed to slide on the bar splines allowing for 1.5 inches of travel and 40° articulation over terrain on the inboard joint. The outboard joint can travel 0.5inches and swing from 45°-47° depending on the model. The Demon heavy duty axles are equipped The TPEE (Thermoplastic polyester elastomer) boots which are stronger, stiffer, more fatigue resistant, puncture resistant, and more temperature resistant than a standard OEM boot. Axles use molybdenum grease to provide low friction and smooth motion. Trust in Demon Heavy Duty Axles to keep you riding!! • 15%-20% increase in diameter compared to regular axle • Inner cage made up of 4340 chromoly steel • Dual heat treated high strength chromoly steel shaft • Thermoplastic polyester elastomer (TPEE) Boot • 10%-15% increase in CV joint size compared to regular joints • Wider articulation angles • Dual plunge design prevents axle from binding • Packed with high load molybdenum grease Precision CNC machined • Can Fit 1.5”- 5” Bracket lift of particular brands/ All Portal Gear Lifts / 1.5”- 5” A-arms of particular brands • 1-year ltd warranty
- New Demon Heavy Duty Axle Rear Right (throttle side) Fits: 2019+ ATV Outlander/Renegade 650 850 1000R Part number PAXL-3065HD Replaces OEM 705502711 705502713 705503024 Through years of research and development Demon Powersports has developed an axle that doesn’t burn a hole in your pocket and adheres to the highest quality standards. These axles are bigger, beefier, and stronger. Demon Heavy Duty Axles are built using larger CV joints and shafts, paired with our proprietary dual heat treatment process, and 4340 Chromoly Steel inner CV cage gives these the axles the edge it needs for superior strength and longevity. These axles also utilize a unique double plunge design which allows it to achieve higher articulation angles approximately, the axles are designed to slide on the bar splines allowing for 1.5 inches of travel and 40° articulation over terrain on the inboard joint. The outboard joint can travel 0.5inches and swing from 45°-47° depending on the model. The Demon heavy duty axles are equipped The TPEE (Thermoplastic polyester elastomer) boots which are stronger, stiffer, more fatigue resistant, puncture resistant, and more temperature resistant than a standard OEM boot. Axles use molybdenum grease to provide low friction and smooth motion. Trust in Demon Heavy Duty Axles to keep you riding!! • 15%-20% increase in diameter compared to regular axle • Inner cage made up of 4340 chromoly steel • Dual heat treated high strength chromoly steel shaft • Thermoplastic polyester elastomer (TPEE) Boot • 10%-15% increase in CV joint size compared to regular joints • Wider articulation angles • Dual plunge design prevents axle from binding • Packed with high load molybdenum grease Precision CNC machined • Can Fit 1.5”- 5” Bracket lift of particular brands/ All Portal Gear Lifts / 1.5”- 5” A-arms of particular brands • 1-year ltd warranty
- New Demon Heavy Duty Axle Rear Left Fits: 2019+ ATV Outlander/Renegade 650 850 1000R Part number PAXL-3064HD Replaces OEM 705502710 705503025 705502712 Through years of research and development Demon Powersports has developed an axle that doesn’t burn a hole in your pocket and adheres to the highest quality standards. These axles are bigger, beefier, and stronger. Demon Heavy Duty Axles are built using larger CV joints and shafts, paired with our proprietary dual heat treatment process, and 4340 Chromoly Steel inner CV cage gives these the axles the edge it needs for superior strength and longevity. These axles also utilize a unique double plunge design which allows it to achieve higher articulation angles approximately, the axles are designed to slide on the bar splines allowing for 1.5 inches of travel and 40° articulation over terrain on the inboard joint. The outboard joint can travel 0.5inches and swing from 45°-47° depending on the model. The Demon heavy duty axles are equipped The TPEE (Thermoplastic polyester elastomer) boots which are stronger, stiffer, more fatigue resistant, puncture resistant, and more temperature resistant than a standard OEM boot. Axles use molybdenum grease to provide low friction and smooth motion. Trust in Demon Heavy Duty Axles to keep you riding!! • 15%-20% increase in diameter compared to regular axle • Inner cage made up of 4340 chromoly steel • Dual heat treated high strength chromoly steel shaft • Thermoplastic polyester elastomer (TPEE) Boot • 10%-15% increase in CV joint size compared to regular joints • Wider articulation angles • Dual plunge design prevents axle from binding • Packed with high load molybdenum grease Precision CNC machined • Can Fit 1.5”- 5” Bracket lift of particular brands/ All Portal Gear Lifts / 1.5”- 5” A-arms of particular brands • 1-year ltd warranty
- Fits all 500, 650, 800, 800R, 570, 850, 1000, 1000R and 1000R turbo Mavericks Outlanders, Renegades, and Commanders. Replaces OEM part numbers 715000302, 422280360, 715900212, and 422280364. This will not fit: Defenders, Maverick X3 or Maverick Sport/Trail Part number MMCA302 This belt is built specifically for the straight mud rider that needs a ton of belt squeeze to stop from slipping the belt. The specific compounds in this belt make it instantly grab when the clutching and tune are correct. Note: This blend of compounds and thickness will build more heat at higher speeds, so we recommend keeping it under 35mph Mud Monster Belt Line Higher strength compared to OEM and aftermarket drive belts. Mud Monster belts have been developed with the 2nd Generation compound called DUMAX2 for added strength, flexibility, and heat resistance. You can squeeze this belt a lot harder for more tuning possibilities and less slippage. Maximum under-cord stiffness allows the belt to flex for rotational efficiency and running cooler temperatures Built thicker when possible for more belt to sheave adhesion. Built for extreme abuse, and excessive shock load. Handles higher temps than OEM Built with Aramid fiber cord to eliminate stretching like a Polyester cord. Made in the USA!
- Brand new aftermarket secondary clutch assembly This is found on many BRP ATVs. Please ask if you have fitment questions. Replaces OEM Part Part Numbers: 420280173 420280176 420280178 420932421 420280236 420280499 420245910 420245911 420220913 If your machine has a spring with pigtails you will need to use a spring without them as this aftermarket clutch does not have provisions for them. 420238176 OEM Black/Orange is a great substitute Installation Torque Specs: 45 ft·lb On the Secondary Bolt (red thread locker recommended, allow to set up overnight)
- OUT OF STOCKNEW OEM Speedometer trim found on Renegade XMR models. Part number 705015189