SP1 Radiator Relocation Kit Replacement Latch Kit. Replaces OEM 860200239 517303981 517304075 Kit includes 2 Latches. Enough to retain one radiator access panel.
NEW OEM Can Am Tool M8x1.25 Tapered Bolt Part number 529036098. This tool fills a few roles, used to open the secondary clutch on many models. This will also lock the crankshaft on Vtwin's and three cylinder models. If you are unsure on application please reach out to us, we are here to help!
New Air filter made by All Balls Racing. This is an OEM replacement filter for early G1 500 650 800HO Outlander or Renegade Please note this will not fit the 800R ATVs Replaces OEM 707800174- OUT OF STOCK
NEW Quad Logic Brand G2 ATV Can Am Airbox Seal Part number 500-1139-PU This is an improved design over factory Apply a small amount of grease to aid install, this is much thicker and denser than the OEM o-ring or gasket Replaces OEM part numbers: 293300165 293300175 293300179 
New OEM Differential Pinion Seal. Please check your wear ring, if that is grooved it is time to replace. Very easy to miss that and blame a new seal on a bad wear ring. Will fit: Gen 1 Front and Rear Diffs Gen 2 Outlander and Renegade Front and Rear Early Commander Rear All Maverick and Commander Front WILL NOT FIT G2 XMR 800/850/1000 REAR DIFFERENTIAL Measurements are shown: 70mm outside and 37mm inside Part number 705401481
NEW OEM Can-am rear driveshaft retaining bolts. Don’t know your size? These are the two most common sizes. M12 x 16 and M10 x 16 with washers. Ships exactly as pictured. On the M12x16 bolt we recommend adding thread locking compound before installation. Thread pitch is 1.25
NEW OEM 20 spline yoke. This fits on large gearboxes output shafts. 20 spline yoke partially machined to accept a protector ring. This is the forward most yoke on the REAR driveshaft. Works with 398 U joints. found on Vtwin rear driveshafts. Part number 715900129 replaces 705501373 and 715900234
NEW OEM Can-am Output Crank Shaft Seal This is the engine out put shaft seal, pressed into the crankcase PTO cover 34mm Inner Diameter 52mm Outer Diameter 8mm Thick Current Part Number 420631933 Replaces Part Number 420631932- OUT OF STOCK
NEW Genuine OEM Fuel/Gas Cap Fits most every Can-am ATV Renegade or Outlander Part Number: 513033025 
G2 ATV brake caliper seal kit 21-83170 These fit G2 ATV brake calipers, if you have fitment questions please reach out, we are here to help
Brand New Genuine OEM Wear ring a must if you are replacing your pinion seal, these are the sacrificial parts that save your drive shaft from grooving! Will fit 18 and 20 Spline Yokes that are fully machined Part Number 705400036
Can-am Rubber Trailing Arm cover and Oetiker clamp for your G1 Outlander or Renegade Will only work on the gen 1 Outlander and Renegades 2006-11 and some 2012 models. If you are unsure on fitment, please ask. You will need to order qty 2 to replace both sides. Genuine OEM parts Part Numbers: 706000222 706000749 293650162
Brand New OEM PTO Cover Gasket for V-Twin Engines Part number 420651211
EPI Ball Joint Kit G1 Fits Outlander 650/800 Upper Renegade 500/800 Lower or Upper Heavy Duty Steel housing with isolated design joint for long life Ball joint includes ball joint, rubber boot, snap ring and cotter pin EPI Part Number: WE351039 P/U Part Number: 0430-0610 Replaces OEM Part Number: 706200653
Air Filter for G1 Outlander and Renegades. Replaces OEM 707800174 Fits 500, 650, and 800HO NON-R 800 engines, from 2006 – 2012. Bonded, two-layer .65" foam designed for maximum protection and airflow Coarse outer foam traps large particles while fine inner foam catches the finest dust With the precision pre-oiled air filter, there is no excess oil to rob horsepower, and no dry spots endangering your engine Made in the U.S.A.
New OEM 18 spline yoke with fully machined surface This is the forward most yoke on the rear driveshaft of G1 ATVs Fits years 2006 and newer, 450 and larger machines, if you are unsure on fitment please contact us. Use with 398 type U joints Current Part number 715900101 Replaces 705500371 705501372
Brand New Moose Utility 13 Bolt CVT Cover Gasket
Works on 7 bolt covers also.
Part number 0935-1193
replaces: 420430127 420430126 420430124 420430123 420430120
Plain bearing half 40 X 43 X 15 This fits into one side of the connecting rod. part number 420233980- OUT OF STOCK
CVTech Primary Clutch Holding tool. Very nice tool for torquing nut on the clutch or the bolt holding clutch on to the crankshaft taper. 0155-1018 Part number 
Please verify your differential uses this style of Seals before ordering! Can Am Standard Rear Differential Pinion and Axle Seals (Timken or SKF) Please measure your parts before ordering to verify fitment. The Pinion Seal has a 70mm Outer Diameter and the standard 37mm inner diameter. Replaces part number 705401481 The Axle Seal has a 52mm Outer Diameter And the standard 30mm inner diameter. Complete Seal kit for Standard Rear differentials common to find in 2016 and newer ATVs or if your differential has been repalced.
New short wiring harness for rear tail lights Will need to be wired in to work. This plugs in to Tail light part number 710001645 Fits: G2 ATV's with dual tail lights, Commanders, and Mavericks (non X3/Sport/Trail)
HD Clutch bolt set for most every Can-am V-twin 2006 to current. Will not work on: Maverick Turbo Maverick X3 Maverick Sport Maverick Trail Defender These will swap out the factory Torque To Yield (TTY) bolts/studs. M10 and M12 Black-Oxide Alloy Steel Socket Head Bolt These are class 12.9 bolts, with a tensile strength of 170,000 psi, these alloy steel bolts are stronger than Grade 8 steel bolts. 8 and 10mm Allen Sockets required to install these bolts. 18-8 Stainless Steel Single-Wave Washers included, these help prevent loosening, use with your existing washers. Installation Torque Specs: 80 ft·lb On the Primary Bolt 45 ft·lb On the Secondary Bolt (red thread locker recommended, allow to set up overnight)
NEW MRRPM Upper Motor Mount for installing 'big block" 1000 engines into a G1 chassis Steel, black in color
Replaces OEM part number 420222691 Upgrade your plastic thermostat housings/water neck on your vtwin 500/570/650/800/850/1000 SOLD AS PAIR These will work in Commanders, Mavericks, Outlanders & Renegades- OUT OF STOCK
NEW OEM G2 ATV Battery Hold Down Fixation Plate Kit. This retains the battery in place, and gives your seat something to latch into Kit includes: Fixation Plate 710009129 replaces 710002404 Positive Battery Terminal Cover 710006729 Rubber Stopper 705014429 Three aftermarket stainless bolts 
OEM Air Filter for Gen 1 Outlander and Renegades. Fits 500, 650, and NON-R 800 engines, from 2006 - 2012. Comes as Pictured.
NEW Chrome Conical Taper M10 Lug Nut Set of 16 M10x1.25 thread size 60 Degree taper 14mm Hex head size, great for use with aftermarket wheels where socket space is a concern These will work on every Canam ATV since 2006 and most every Canam sxs Will not fit the Maverick X3 12mm wheel studs. Part numbers: 57-94121, ALUG14BX
Have Questions?
Our staff is available to answer questions
canampartsguy@gmail.com
1340 Okray Ave.
Plover, WI 54467
jared@canampartsguy.com
Cant find What you're looking for?
Visit our 
store!
2016 Can Am Parts, LLC. All rights reserved.