- OUT OF STOCK
Brand New Genuine OEM XPS Full Synthetic Oil Change Kit.
Ultra convenient “all in one” kit saves time and money.
For Can-am off road vehicles with 500cc or larger Rotax engines. Excludes Traxter and Quest.
Not compatible with Maverick X3
Includes 2 quarts plus 1 16 fl oz of 4T synthetic oil 5W40, 0-rings, rotax oil filter, and copper washer for old style and new style drain plugs.
May not ship in original box
Part Number: 779258 replaced by 9779488
- This is the 2019+ rear differential found in Renegades and Outlanders 650 and larger This has the 6 inch (155mm) ring gear with straight cut teeth as shown. It will fit g2 bikes (500/650/800/1000) if you are upgrading you will need to shorten your shaft 1.75 inches or buy a kit from us, please see our other listings. (G1 bikes will require further modifications to work). This has a provision for an abs sensor, but will fit bikes without a rear diff sensor BRP claims 25% increase in load capacity on this gear set vs the spiral cut xmr final drive units (rear differentials) from 13-18 models. Pinion spline count 20 Current part number 705502808
- BOYESEN SUPERCOOLER WATER PUMP Cover and Impeller Kit Increased coolant flow at all rpm ranges Patented Nautilus-style impeller for hydrodynamic efficiency Color/Finish: Black, Powder-Coated Material: Aluminum Model: Supercooler Part number 0932-0166 WPK-80B Replaces OEM 420222505 420222785 703501124 This is the style with the smaller output nipple roughly 7/8 inch in outer diameter.
- OUT OF STOCKCan-am Shim Kit for XMR G2 800 or larger 2012-current Rear Differentials. Part number 703500835
- New Oem Canam Pinion nut, this is spun on to the pinion gear to retain the bearings on the pinion gear of xmr differentials on ATV XMR's G2 800/850/1000/1000R This is not needed on 570 or 650 XMR models The threads are M28x1.25 Right Hand the outer diameter is 51mm Please check that this is the correct nut for your application Part number 705501550
- EPI Ball Joint Kit G1 Fits Outlander 650/800 Upper Renegade 500/800 Lower or Upper Heavy Duty Steel housing with isolated design joint for long life Ball joint includes ball joint, rubber boot, snap ring and cotter pin EPI Part Number: WE351039 P/U Part Number: 0430-0610 Replaces OEM Part Number: 706200653
- SHIPS FREE TO THE LOWER 48 STATES
- LED dimmer facilitates reading temperature settings.
- 4 temperature settings with individual controls for thumb and grips.
- Returns to previous heat setting.
- One-touch shutdown.
- Wiring Harness (710004567) required for installation, on G2L and G2S (except 1000R and T category models) G2 Outlander does not require the harness.
- NEW OEM O-rings and hex bolts to install inner CVT cover on most Can-Am V-twins. Works on 7 and 13 bolt inner covers Part numbers: O-rings - 420430407 and 420631087 old numbers 420430408 420631088 Hex Bolts - 420440207 Also has a nut and washer for 1000 cover installation - 232561434, 224061121 Will come as pictured
NEW Bearing and Seal Kit for Can-Am Outlander and Renegade Rear Trailing Arms
They fit G2 Models (2012+)
Replaces part numbers 293350145 706000826 293200132 293200144
This is enough bearings and seals to do both rear arms (some newer models only use half the bearings)
These are high quality KOYO bearings and SKF/Dichtomatik seals.
- Can-am Rubber Trailing Arm cover and Oetiker clamp for your G1 Outlander or Renegade Will only work on the gen 1 Outlander and Renegades 2006-11 and some 2012 models. If you are unsure on fitment, please ask. You will need to order qty 2 to replace both sides. Genuine OEM parts Part Numbers: 706000222 706000749 293650162
- NGK 4339 DCPR8E Standard Plug Fits All G1 ATV's OE numbers: 707000246 715900637 Thread Size: 12mm Thread Pitch: 1.25mm Seat Type: Gasket Resistor Value: 5K Ohm Reach: 19mm (3/4") Hex Size: 5/8" (16mm) Terminal Type: Removable Nut (you will need to remove this for use on G1 ATV's) Gap: .028" (0.7mm) Torque Specs Aluminum: 10.8-14.5 lb. ft. Brand: NGK Heat Range: 8 Longevity: 30k Miles Resistor: Yes Projected Material: Nickel Quantity: 1
Fits G2 ATV’s Outlander or Renegade 500 450 570 650 800 850 1000 1000R
Shift Arm Base Upgrade
Replaces OEM 707003054 707000971 707002439
USA made Made from 6061 T6 Aluminum (aircraft grade)
This plate does not require any additional hardware, use a zip tie to retain the wire harness or vent lines running near it.
- EPI Bushing Kit, steel inner, plastic outer bushings and shimsFits: G2 Canam ATV’s Outlander or RenegadeDefender and CommanderIf you are unsure on fitment, please contact us before purchasing!Exact replacement components to return your suspension to like-new conditionKits are sold per A-armEPI Part Number: WE341052P/U Part Number: 0430-1029Replaces OEM Part Numbers: 703500875 706202088 706202089 706202133