- SHIPS FREE TO THE LOWER 48 STATES Late G1 Early G2 Standard Rear Differential Rebuild Kit There are a few options for rebuild kits, please measure your parts before ordering!! OEM Rear Differential Gear set 10/36 Ring and Pinion gear set. The gears are straight cut as pictured. Paired with high quality aftermarket bearings along with double lip axle seals. This kit should be installed by an experienced technician. Ring gear shims are included as the gears will need to be set up in your cases, the pinion shims should remain unchanged Note: the O rings are not included, this is a cost savings measure as they are generally reusable. There are a few options for kits, please verify your differential uses this style of gears before ordering! This will only fit six mounting hole differentials. Open up the differential! Check for two bearings total (one on each side) on the ring gear. If you only have two proceed to the next measurement. Measure your outer diameter of your axle seals! They should measure close to 1 3/4" (47mm) To further verify fitment you can measure your pinion pilot shaft, this should be 9/16? (14mm) The last pictures show this very clearly. Please take the time to measure your parts before buying this will save time and restocking fees.
- CVtech Trail Bloc Primary Clutch with HD retaining bolt, calibrations are for ATVs not UTVs Solid upgrade over the factory unlocked primary clutch, this is a straight bolt on replacement. Locked sheaves, smaller one-way diameter and more belt grip. This is a great clutch for riders looking for a performance upgrade. This comes preset, some fine tuning may be required to get this 100% Many find these settings to be spot on. We will provide assistance in fine tuning for your riding style. Please allow additional 1-2 day handling time.
- New OEM Differential Pinion Seal. Please check your wear ring, if that is grooved it is time to replace. Very easy to miss that and blame a new seal on a bad wear ring. Will fit: Gen 1 Front and Rear Diffs Gen 2 Outlander and Renegade Front and Rear Early Commander Rear All Maverick and Commander Front WILL NOT FIT G2 XMR 800/850/1000 REAR DIFFERENTIAL Measurements are shown: 70mm outside and 37mm inside Part number 705401481
Cvtech 1 Way assembly bearing for use on all canam cvtech primary clutches. *will not fit other makes*
Part number 0940-0001
35mm Inner Diameter
52mm Outer Diameter
24mm WideThis is a great video showing how to install –>>LINK HERE<<–
- SHIPS FREE TO THE LOWER 48 STATES Set of Bearings and Seals to Rebuild Your Front Differential on Your Can-Am Fits Most Can-Am Models from 2007-Current (WILL NOT FIT Maverick X3/Sport/Trail or Defender) This Kit has High Quality Aftermarket Bearings which are: Timken, SKF, NSK, KOYO, Nachi Comes with: 2 - Carrier Bearings- SKF Brand 2 - Axle Bearings- OEM NSK Japan made 2 - Axles Seals- Timken 1 - Inner Pinion Bearing- Nachi Japan made 1 - Large Pinion Bearing- Koyo Japan made 1 - Pinion Seal
- High quality Timken axle oil seal. Fits ATV front differentials 2006-current, some UTV's To be 100% sure on fitment, measure your outer diameter on your seal, it should read 47mm This seal has a 25mm inner diameter 47mm outer diamter and is 7mm thick. Replaces OEM 705500255 705500081 Order qty two per machine.
- EPI Ball Joint Kit G1 Fits Outlander 650/800 Upper Renegade 500/800 Lower or Upper Heavy Duty Steel housing with isolated design joint for long life Ball joint includes ball joint, rubber boot, snap ring and cotter pin EPI Part Number: WE351039 P/U Part Number: 0430-0610 Replaces OEM Part Number: 706200653
- EPI Bushing Kit, steel inner, plastic outer bushings and shims Set of 4 Fits: Can Am ATV’s Outlander or Renegade and Commander If you are unsure on fitment, please contact us before purchasing! Exact replacement components to return your suspension to like-new condition Kits are sold per A-arm EPI Part Number: WE341043 P/U Part Number: 0430-0707 Replaces OEM Part Numbers: 706200051 706200181 706200157 Ships as Pictured
- This model type is a rubber O.D. seal with two sealing lips. The main sealing lip is spring loaded. This is a two-way seal, which means that it can retain lubricant and exclude contaminants simultaneously Canam Vtwin crankshaft main seal. Replaces OEM number 420631933 This seal is pressed into the PTO cover on v-twin's Unsure on fitment? Just measure you seal. 52mm Outer Diameter 34mm Inner Diameter 8mm Thick
- New Genuine OEM IACV idle air control valve bypass, this is what controls the idle speed of your ATV. Will fit on most any Vtwin 2006-current Can Am Outlander Renegade models. Will not fit 850 or 1000R engines with the 54mm throttle body. Old part numbers 420665940 420963055 420963057 Current part number 420665941
- Please verify your differential uses this style of seals before ordering! Can Am Rear Differential Pinion and Axle Seals (Timken or SKF) Fit on most 2006-2013 Outlanders and Renegades The Pinion Seal has a 70mm Outer Diameter And the standard 37mm inner diameter. The Axle Seal has a 47mm Outer Diameter And the standard 30mm inner diameter. Complete Seal kit for Standard Rear differentials Replaces OEM Numbers: 705400027 705500751 705501996 705401481
- 20 Spline Yoke with Wear ring installed. Fits: XMR 1000, Maverick and '14&newer Commander style Rear differentials. These yokes are made to very tight tolerances, if you are not careful when installing these you can damage the yoke or your pinion shaft. We recommend you take your time and clean the pinion gear before installing. ---Great for custom applications--- Uses Factory size U joint (398 at the auto parts store) Part numbers 715900271 705400036
- Can-Am 703500865 Secondary Clutch Driven Pulley Stud Nut Screw Kit Secondary Stud/Nut Kit M10x136mm You will need to reuse your washer. This kit will work on every Vtwin ATV factory driven (secondary) clutch (pulley) Also fits Commander driven clutch Will work on non QRS Maverick driven clutch If you have fitment questions, please contact us, we are here to help. Part numbers: 703500865 420441900 420242097 420242402
- NEW OEM Can-Am Variator CVT Clutch Outer Cover Belt Box This part is made for 2016-current Outlander and Renegade 1000R’s Perfect for a machine with a larger aftermarket clutch or any machine using a Maverick Primary with a stud/nut, as this cover has more room inside. **NOTE: This cover does not have any extra venting holes** Current Part number: 420612316 Old Part number: 420612310