BRAND NEW Can Am OEM Wheel Cap This is for a set of Four (4) Caps Part Number 705400928 There is more than one style. Please verify that this is the correct style BEFORE ordering.
CVTech Primary Clutch Holding tool. Very nice tool for torquing nut on the clutch or the bolt holding clutch on to the crankshaft taper. 0155-1018 Part number
CVtech Trail Bloc Primary Clutch with HD retaining bolt, calibrations are for ATVs not UTVs Solid upgrade over the factory unlocked primary clutch, this is a straight bolt on replacement. Locked sheaves, smaller one-way diameter and more belt grip. This is a great clutch for riders looking for a performance upgrade. This comes preset, some fine tuning may be required to get this 100% Many find these settings to be spot on. We will provide assistance in fine tuning for your riding style. Please allow additional 1-2 day handling time.
NEW OEM Tool 529036302 This removes the large housing nut on G2 XMR Rear Differentials Also works on 2019 ATV Rear differential housing nuts. please note there may be some casting flare on your housing nut you may have to file to get the tool to fit, as it is a very tight fit.
New OEM Differential Pinion Seal. Please check your wear ring, if that is grooved it is time to replace. Very easy to miss that and blame a new seal on a bad wear ring. Will fit: Gen 1 Front and Rear Diffs Gen 2 Outlander and Renegade Front and Rear Early Commander Rear All Maverick and Commander Front WILL NOT FIT G2 XMR 800/850/1000 REAR DIFFERENTIAL Measurements are shown: 70mm outside and 37mm inside Part number 705401481
Brand New OEM Stator Cover Gasket for V-Twin Engines. Fits 2006-Current V twin’s Part number 420651201
New NGK Spark Plug 93444
OEM part number 715900352
NGK part number LMAR8D-J
These spark plugs work in 2015+ Outlander/Renegade 450 850 and 1000R also fits Defender HD5
Shell
Thread Diameter: 10mm
Thread Pitch: 1.0mm
Seat Type: Gasket
Reach: 26.5mm (1.04″)
Hex Size: 9/16″ (14mm)
Terminal Type: Solid
Gap: .031″ (0.8mm)Center Electrode
Material: Nickel
Type: Standard
Size: 2.5mm
Projection: ProjectedGround Electrode
Material: Nickel
Type: Multi-GroundSpecifications
Resistor: Yes
Resistor Value: 5k Ohm
Heat Range: 8
Torque Specs: Aluminum: 7.2-8.7 lb. ft.
SHIPS FREE TO THE LOWER 48 STATES
Late G1 Early G2 Standard Rear Differential Rebuild Kit
There are a few options for rebuild kits, please measure your parts before ordering!!
OEM Rear Differential Gear set 10/36 Ring and Pinion gear set. The gears are straight cut as pictured.
Paired with high quality aftermarket bearings along with double lip axle seals.
This kit should be installed by an experienced technician. Ring gear shims are included as the gears will need to be set up in your cases, the pinion shims should remain unchanged
Note: the O rings are not included, this is a cost savings measure as they are generally reusable.
There are a few options for kits, please verify your differential uses this style of gears before ordering! This will only fit six mounting hole differentials.
Open up the differential! Check for two bearings total (one on each side) on the ring gear. If you only have two proceed to the next measurement.
Measure your outer diameter of your axle seals!
They should measure close to 1 3/4" (47mm)
To further verify fitment you can measure your pinion pilot shaft, this should be 9/16? (14mm)
The last pictures show this very clearly. Please take the time to measure your parts before buying this will save time and restocking fees.
NEW OEM Screw Part number 235381646 M8x16
High quality Timken oil seal. Replace a leaking front output seal on your canam. This is the seal that seals the engine through shaft coming out of the front of your Vtwin engine below the front exhaust header. To be 100% sure on fitment, measure your outer diameter on your seal, it should read 47mm This seal has a 25mm inner diameter 47mm outer diamter and is 7mm thick. Replaces OEM part numbers: 420430588 420430589 420430580
NEW OEM Shock Bushing for base black body hydraulic type shocks. These will fit: 2020 and prior Commanders 800 800R 1000 1000R G1/G2 Outlanders 400 450 500 570 650 800HO 800R 850 1000 1000R Oem part number 715900122
SHIPS FREE TO THE LOWER 48 STATES Standard G2 Rear Differential Bearing and Seal Kit High quality aftermarket bearings along with double lip axle seals. Bearing and Seal Brands include: Nachi, KOYO, NTN, Timken, SKF The large case sealing and pinion gear O-rings are NOT included as a cost saving measure, these O-rings are reusable if not damaged. There are a few options for kits, please verify your differential uses this style of gears before ordering! This will only fit six mounting hole differentials. Open up the differential! Check for two bearings total (one on each side) on the ring gear. If you only have two proceed to the next measurement. Measure your outer diameter of your axle seals! They should measure close to 2 1/16″ (52mm) To further verify fitment you can measure your pinion pilot shaft, this should be 5/8″ (16mm) The last pictures show this very clearly. Please take the time to measure your parts before buying this will save time and restocking fees. Fits 2015 and newer G2 style ATV 500/570/650/800/850/1000/1000R NON-XMR style REAR differential.570/650 XMR machines do not have the true XMR differential.
Have Questions?
Our staff is available to answer questions
canampartsguy@gmail.com
1340 Okray Ave.
Plover, WI 54467
jared@canampartsguy.com
Cant find What you're looking for?
Visit our 
store!
2016 Can Am Parts, LLC. All rights reserved.