NEW OEM Can Am O ring 705502064 This seals the two cases together on standard rear differentials.- OUT OF STOCK
Aftermarket Four wheel drive servo motor. This is what engages the sliding collar putting power to the front differential. Part number 715900614 420891087 415129174 
New IKO, Koyo or NTN brand needle bearing B98 replaces 705500261 If you are unsure on fitment please reach out to us we will help.
NEW OEM Large Gearbox NEW OEM Can-am Part NOT A REBUILD, ALL NEW Brand New In The Box Part number 420686214 This gearbox is used in the following: 2019-2024 Renegade/Outlander 1000R XMR If unsure of fitment, please contact us. We will be happy to help!
Curly Built Maverick Swap Brackets with precut aftermarket Maverick rear differential. These beefy brackets allow you to install a huge Maverick rear differential into your G2 ATV. This kit places the pinion in the same place as an XMR rear differential, meaning 2012-2018 800/850/1000 XMR ATVs will be able to use the stock driveshaft. All 2019 and newer G2 650/850/1000 models also use the stock driveshaft. If you have questions on fitment we are here to help. This requires you to cut your frame, trim brackets and drill a few holes instructions are provided here. If you are mechanically inclined figure 3-4 hours for install.
Brand New Genuine OEM front differential This is the visco 4lok model which has the electronic locking mechanism Part number 705403049 replaces 705402700 This is found in the 2021+ G2 XMR, XTP and XXC models. You will need to transfer over your fill plug after filling this with gear oil.
Gearbox Shift Shaft Seal 28mm OD 12mm ID 7mm Thick Part numbers: 711250450 420250450
Differential Vent Tube 8mm diameter Part number 705501584
New OEM Can Am Outlander, Renegade 1000R XXC Gearbox
Current Part Number- 420686568
Previous Part Numbers- 420686565 NEW OEM Canam PartNOT A REBUILD, ALL NEW Brand New In The Box
Fits- Maverick 1000R, Commander 1000 or 800, Outlander 1000 2012-2014, all Outlander XMR 1000/1000R, Renegade 1000/1000R.
If unsure of fitment, please contact us. We will be happy to help!These ratios are published in the 2019 Service manual, we have not confirmed these to be accurate.
Ring and Pinon Gears 37/15=2.467
Intermediate 45/40=1.125
High Range 36/27=1.333
Low Range 46/17=2.706
Reverse 34/12=2.833Overall Gear Ratios:
High Range 3.700
Low Range 7.510
Reverse Range 7.863
New Oem Canam Pinion nut, this is spun on to the pinion gear to retain the bearings on the pinion gear of xmr differentials on ATV XMR's G2 800/850/1000/1000R This is not needed on 570 or 650 XMR models The threads are M28x1.25 Right Hand the outer diameter is 51mm Please check that this is the correct nut for your application Part number 705501550
1447 NEW OEM Needle bearing 14x20.65x19 Size These are KOYO Bearings high quality 14mm Inner Diameter 20.65mm Outer Diameter 19mm Long Replaces OEM Part number 705501408
SHIPS FREE TO THE LOWER 48 STATES NEW OEM Canam Parts OEM 14% LOWER LOW GEAR SET for most every 1000 Vtwins minus north american 2015 and newer outlander 1000/1000R This is the way to reduce the over all Low Gear ratio on your can-am 1000 running larger tires. This is the LOW RATIO for any Large Gearbox. The last picture shows a Large gearbox. This will not fit Small Gearboxes. 14% lower gear ratio than standard 1000 gear boxes (Maverick, Commander, Renegade, Outlander) Will also fit 800 Commander
Have Questions?
Our staff is available to answer questions
canampartsguy@gmail.com
1340 Okray Ave.
Plover, WI 54467
jared@canampartsguy.com
Cant find What you're looking for?
Visit our 
store!
2016 Can Am Parts, LLC. All rights reserved.