- OUT OF STOCKNEW OEM Large Gearbox NEW OEM Can-am Part NOT A REBUILD, ALL NEW Brand New In The Box Part number 420686214 This gearbox is used in the following: 2019-2024 Renegade/Outlander 1000R XMR If unsure of fitment, please contact us. We will be happy to help!
New OEM Can Am Outlander, Renegade 1000R XXC Gearbox
Current Part Number- 420686568
Previous Part Numbers- 420686565 NEW OEM Canam PartNOT A REBUILD, ALL NEW Brand New In The Box
Fits- Maverick 1000R, Commander 1000 or 800, Outlander 1000 2012-2014, all Outlander XMR 1000/1000R, Renegade 1000/1000R.
If unsure of fitment, please contact us. We will be happy to help!These ratios are published in the 2019 Service manual, we have not confirmed these to be accurate.
Ring and Pinon Gears 37/15=2.467
Intermediate 45/40=1.125
High Range 36/27=1.333
Low Range 46/17=2.706
Reverse 34/12=2.833Overall Gear Ratios:
High Range 3.700
Low Range 7.510
Reverse Range 7.863- OUT OF STOCKAftermarket Four wheel drive servo motor. This is what engages the sliding collar putting power to the front differential. Part number 715900614 420891087 415129174
- 2012-2018 G2 ATV Rear Differential Swap Kit Kit includes: Rear Differential, Rear driveshaft, Bolt and Washer. This kit includes a rear differential with: Tapered roller bearings Three bearings on the pinion gear 6 inch diameter ring gear Your choice of gear style, spiral bevel or straight cut. Both have the same 3.60 ratio as your current differential. Spiral Bevel Gears are sourced from the 2013-18 800 850 and 1000 XMR differentials. Current part number 705502546 Old part numbers: 705502178 & 705502090 Straight Cut gears are sourced from the 2019+ 650+ differentials. Current part number 705502808 The driveshaft included is an OEM shaft with the correct end yokes for your application. The differential end yoke will not use a wear ring, this has been done away with by BRP the yoke is what the pinion seal touches now. You will need to fill the differential with 250ml (8.4oz) of 75W-140 gear oil and transfer over your fill plug and washer. The torque spec on the driveshaft retaining bolt is 55ftlbs with thread locker applied. Some minor trimming on the brackets that surround the differential is required. These differentials have the provision for an ABS sensor, this is standard on euro models, for mud riders state side, you can fill this hole with RTV or leave it open. If you are running the silver protector ring on your axle, you will need to push the ring outward slightly. We choose to remove these dust covers as they tend to trap debris when run under water.
There are a few options for kits, please verify your differential uses this style of gears before ordering!
This will only fit six mounting hole differentials.
Late G1 Early G2 Standard Rear Differential Ring 36t and Pinion 10t gear set Pinion bolt size is M10, this may be different than what you are replacing.
OEM Rear Differential Gear set 10/36 Ring and Pinion gear set. The gears are straight cut as pictured. This kit should be installed by an experienced technician.
Open up the differential! Check for two bearings total (one on each side) on the ring gear. If you only have two proceed to the next measurement. Measure your outer diameter of your axle seals! They should measure close to 1 3/4? (47mm) To further verify fitment you can measure your pinion pilot shaft, this should be 9/16″ (14mm) The pictures show this very clearly. Please take the time to measure your parts before buying this will save time and restocking fees.
- SHIPS FREE TO THE LOWER 48 STATES New OEM Standard G2 Rear Differential Ring & Pinion Gear Set 1652 There are a few options for kits, please verify your differential uses this style of gears before ordering! This will only fit six mounting hole differentials. OEM Rear Differential Gear set 10/36 Ring and Pinion gear set. The gears are straight cut as pictured. Open up the differential! Check for two bearings total (one on each side) on the ring gear. If you only have two proceed to the next measurement. Measure your outer diameter of your axle seals! They should measure close to 2 1/16? (52mm) To further verify fitment you can measure your pinion pilot shaft, this should be 5/8? (16mm) Please take the time to measure your parts before buying this will save time and restocking fees. Fits 2015 -2019 G2 style ATV 500/570/650/800/850/1000/1000R NON-XMR style REAR differential. 570/650 XMR machines do not have the true XMR differential.
- OUT OF STOCKNew OEM 2019+ rear differential gear set, 10/36 tooth straight cut ring and pinion gear set, Timken seals, NTN or IKO pilot bearing , OEM shim kit and OEM bearings along with a new bolt and washer to retain the driveshaft. BRP claims 25% increase in load capacity on this gear set vs the spiral cut xmr final drive units (rear differentials) from 13-18 models. Fits differential part numbers: 705502808, 705502546, 705502178, 705502090 703501031 705501550 705501556 705501557
- High quality Timken oil seal. Replace a leaking front output seal on your canam. This is the seal that seals the engine through shaft coming out of the front of your Vtwin engine below the front exhaust header. To be 100% sure on fitment, measure your outer diameter on your seal, it should read 47mm This seal has a 25mm inner diameter 47mm outer diamter and is 7mm thick. Replaces OEM part numbers: 420430588 420430589 420430580
- OUT OF STOCK
Aftermarket Four wheel drive servo motor.
This is what engages the sliding collar putting power to the front differential.
Replaces oem 715900614 4151 29174 420891087
- OUT OF STOCKNEW OEM GEARBOX 570s come with a lower ratio gearbox than the normal low ratio gearboxes found in the 650’s and 500’s The extra low ratio gearbox will help bottom end power and with larger tires, this is the lowest ratio small gearbox. Current Part Number 420686569 Replaces: 420686567 420686560 420686561 This is found in Outlander or Renegade 570 DPS XT or XMR Will work in 650,800,850, and 2015 and newer 1000/1000R ATV’s Teeth count and gear ratio Ring & Pinion 38/28 = 1.357 High Gear set 46/20 = 2.300 Low Gear set 31/14 = 2.214 High final ratio 3.341:1 Low final ratio 5.662:1 2015 and newer non XMR outlander 1000’s have this style gearbox, if you have fitment questions, please contact us! If you are installing this on an early G1 ATV you will need to transfer over your gear position sensors.
- High quality Timken axle oil seal. Fits ATV rear differentials 2006-2014 To be 100% sure on fitment, measure your outer diameter on your seal, it should read 47mm This seal has a 30mm inner diameter 47mm outer diamter and is 7mm thick. Replaces OEM 705500751 705501196 and 705501996 Order qty two per machine.
- High quality aftermarket Timken or SKF axle oil seal. Fits ATV rear differentials 2015-current, some UTV’s To be 100% sure on fitment, measure your outer diameter on your seal, it should read 52mm This seal has a 30mm inner diameter 52mm outer diamter and is 8mm thick. Replaces OEM 705501556 Order qty two per machine.
- High quality Timken axle oil seal. Fits ATV front differentials 2006-current, some UTV's To be 100% sure on fitment, measure your outer diameter on your seal, it should read 47mm This seal has a 25mm inner diameter 47mm outer diamter and is 7mm thick. Replaces OEM 705500255 705500081 Order qty two per machine.
- New XPS SAE 75W-90 and 75W-140 Synthetic Gear Oil Kit. Enough to do a complete service on the front differential, rear differential, and gear box 1 U.S QT 946ml per bottle Listing is for 2 Quarts. See your owners manual before ordering to make sure you order the correct weight for your Can Am Part number 779160 and 779158
- New Oem Canam Pinion nut, this is spun on to the pinion gear to retain the bearings on the pinion gear of xmr differentials on ATV XMR's G2 800/850/1000/1000R This is not needed on 570 or 650 XMR models The threads are M28x1.25 Right Hand the outer diameter is 51mm Please check that this is the correct nut for your application Part number 705501550
- OUT OF STOCKCan-am Shim Kit for XMR G2 800 or larger 2012-current Rear Differentials. Part number 703500835
- This is the 2019+ rear differential found in Renegades and Outlanders 650 and larger This has the 6 inch (155mm) ring gear with straight cut teeth as shown. It will fit g2 bikes (500/650/800/1000) if you are upgrading you will need to shorten your shaft 1.75 inches or buy a kit from us, please see our other listings. (G1 bikes will require further modifications to work). This has a provision for an abs sensor, but will fit bikes without a rear diff sensor BRP claims 25% increase in load capacity on this gear set vs the spiral cut xmr final drive units (rear differentials) from 13-18 models. Pinion spline count 20 Current part number 705502808