Renegade

  • Can-am Style Plastic Fender rivet set. NEW Pack of 25 For 8mm (5/16?) holes great for holding plastic fenders together, works on Maverick, Commander, Outlander and Renegade Replaces part numbers 293150089 293150230
  • HD Clutch bolt set for most every Can-am V-twin 2006 to current. Will not work on: Maverick Turbo Maverick X3 Maverick Sport Maverick Trail Defender These will swap out the factory Torque To Yield (TTY) bolts/studs. M10 and M12 Black-Oxide Alloy Steel Socket Head Bolt These are class 12.9 bolts, with a tensile strength of 170,000 psi, these alloy steel bolts are stronger than Grade 8 steel bolts. 8 and 10mm Allen Sockets required to install these bolts. 18-8 Stainless Steel Single-Wave Washers included, these help prevent loosening, use with your existing washers. Installation Torque Specs: 80 ft·lb On the Primary Bolt 45 ft·lb On the Secondary Bolt (red thread locker recommended, allow to set up overnight)
  • NEW OEM Can-am rear driveshaft retaining bolts. Don’t know your size? These are the two most common sizes. M12 x 16 and M10 x 16 with washers. Ships exactly as pictured. On the M12x16 bolt we recommend adding thread locking compound before installation. Thread pitch is 1.25
  • Fits G2 ATV’s Outlander or Renegade 500 450 570 650 800 850 1000 1000R

    Shift Arm Base Upgrade

    Replaces OEM 707000971 707002439

    USA made Made from 6061 T6 Aluminum (aircraft grade)

    This plate does not require any additional hardware, use a zip tie to retain the wire harness or vent lines running near it.

  • Replaces OEM part number 420222691 Upgrade your plastic thermostat housings/water neck on your vtwin 500/570/650/800/850/1000 SOLD AS PAIR These will work in Commanders, Mavericks, Outlanders & Renegades
  • Single CVT cover bolt with the hex head and torx inside. The preferred style to work with. Part number 420440568 replaces 420440567 420440307 Genuine OEM Part A little anti-seize is a great idea when installing these bolts, as the inserts they screw into can easily strip out.
  • NEW Prop Shaft Low profile pair of clamps for 715900118 boot. Clamps also work for G2 front shaft boot 705401093. The last few pictures show the clamps loose, then installed nice and tight. Sold in pairs enough to do one boot.
  • Cast Aluminum Valve cover set with Stainless bolts. Replaces your factory plastic valve covers on any can-am V-twin ATV or UTV 500/570/650/800/850/1000/1000R Replaces OE Numbers: 420610390 420610394 420610393 420610395
  • M8x1.25×70 Bolt. m8-1.25x70mm Used to open the secondary clutch on many Can-am ATV’s & SXS’s Simple tool, trusted seller. Or just use these specs and head to your hardware store.
  • Brand New Genuine OEM Wear ring a must if you are replacing your pinion seal, these are the sacrificial parts that save your drive shaft from grooving! Will fit 18 and 20 Spline Yokes that are fully machined Part Number 705400036
  • Can Am XPS premium coolant extended life premixed do not add water

    Extended Life Premixed Antifreeze/Coolant provides extended protection against rust corrosion and pitting caused by cavitation for all coolant system metals including aluminum.
    It provides protection against radiator freeze-up down to -37*C (-34.6*F) and boil over to 129*C (264.2*F) with a 100 kilopascal (15psi) radiator cap  in good working condition.

    This is orange in color 1 U.S. quart (32 fl. oz) 946 ml

    Part Number: 779150

  • Rear driveshaft U-Joint Replacement 398 style Fits all V-twin Canam rear driveshafts XMR XT XXC XDS XRS STD Grease zerk in cap for easy maintenance Made in Japan High Quality Clips are included just as pictured We recommend pumping fresh grease in after installing, as the grease inside may not be enough for operation. Please note on some older driveshafts the yoke ears may need to be ground down to allow for the larger center part of the joint to be installed. Replaces OEM part numbers: 703500846 715900270 715900278
  • 420927837 Thermostat Gasket

     

    Sold Each, vtwin’s require two per engine.

  • New OEM Can-am Part This boot fits the G2 outlander/renegade front driveshaft. It is the thicker tapered boot, some use two of these on G2 atv's front driveshaft. Part number 705401093
  • New Aftermarket Bellows with clamp, use this in place of vent lines on your differentials. Replaces OEM part number: 705400352
  • Brand new Genuine OEM flexible CVT intake adaptor for Renegade, Outlander, Maverick, and Commander.

    This replaces the thin rubber boot that comes on many early CanAm V-Twin models.

    Very nice upgrade for a cracked CVT intake boot.

    Current part number 707002585

    Previous part numbers 707001467, 707001043, 707000719

  • New OEM Rear driveshaft U-Joint 25mm caps 398 style Fits all V-twin Can Am rear driveshafts Clips are included just as pictured We recommend pumping fresh grease in after installing, as the grease inside may not be enough for operation.
  • OUT OF STOCK
    Brand New Genuine OEM Fill Level Plug Be sure that yours looks the same due to other styles for front or rear differential from different years M14 diameter 1.5 thread pitch Part number 705500504
  • Cam Am rubber bellow for front or rear differential. This is a brand new OEM rubber bellows. Part number 705400352
  • One CVT cover screw with the Torx head. M6 X 30.5 Stainless Part # 420440561
  • Can-am Outlander, Renegade or Commander 500 650 800 1000 6 Bolt HD rear Differential.

    This is an OEM Canam part used in many Generation 2 atvs.

    It does not have the bracket for the rear brake caliper on it.

    This is an updated version with much more substantial webbing for improved support.

    Fits:
    2012 Outlander and Renegade 800, 1000
    2013 to 2018 500/570/650/800/1000 Outlander Renegade
    2011-2013 Commander 800 1000
    2013-2018  XMR 570 and 650

    **WILL NOT FIT** XMR 1000 or XMR 800
    WILL NOT FIT ALL 2019 Models, please contact us if you have a 2019.

    Current Part Number 703501019
    Previous Part Numbers 703500878, 705501896, 705501419, 705501993

  • Rear Differential Seal kit for differentials with 80mm outer diameter pinion seal

    1 Pinion Seal, 80mm
    2 Axle Seals, 52mm

    Brands we use include : Timken, Dichtomatik and SKF

    Fits:
    2013 to Current Outlander 1000/1000R XMR
    2015 to Current Outlander 800/850 Xmr
    2016 to Current Renegade 1000R XMR
    2019 to Current 650 and Larger ATVs
    Also some 2019 to Current 570 XMR (measure your parts to verify fitment)

    *** THIS WILL NOT WORK IN 2013-2018 650/570 XMR or 2011/2012 800 XMR machines. If you are unsure about fitment please contact us! ***

  • 293370019 NEW OEM BRP Clip Retains the wheel bearing in the knuckle on many machines Unsure on fitment? Please ask us, we will do our best to help.
  • Please verify your differential uses this style of Seals before ordering! Can Am Front Differential Pinion and Axle Seals (Timken) Fit on most all 2006-2019 Outlanders and Renegades Also fits Commanders and Mavericks (non X3/Sport/Trail) The Pinion Seal has a 70mm Outer Diameter And the standard 37mm inner diameter. Replaces part numbers 705401481 705500255 705500081 The Axle Seal has a 47mm Outer Diameter And the standard 25mm inner diameter. Replaces part numbers 705401618 705401486 Complete Seal kit for Standard Front Differentials

Title