- OUT OF STOCKNew OEM 2019+ rear differential gear set, 10/36 tooth straight cut ring and pinion gear set, Timken seals, NTN or IKO pilot bearing , OEM shim kit and OEM bearings along with a new bolt and washer to retain the driveshaft. BRP claims 25% increase in load capacity on this gear set vs the spiral cut xmr final drive units (rear differentials) from 13-18 models. Fits differential part numbers: 705502808, 705502546, 705502178, 705502090 703501031 705501550 705501556 705501557
Features:
Cable adapter and fasteners constructed of highest quality stainless steel
Gold anodized aluminum throttle lever can be operated with one finger for safer side hilling
Safety features include rubber accordion boot (keeps moisture out of cable housing) and safety pin (locks left throttle from unwanted use)
Kit includes all hardware, allen wrenches and instructions for installation in approximately 20 minutes
Part Number 12-71042
Brand Number: 007-1011A- New Genuine OEM Robust injected-polypropylene construction allows for the right fit and easy installation Adjustable unit safely holds smartphones or small tablets with a length or width measuring between 2.9" (7.5 cm) and 5.1" (13.0 cm) with or without protective case Integrated storage 0.6 Gal Guiding wire grooves to pass charging cable through the lid Possibility of relocating 12V power outlet or installing USB outlet in storage compartment Not compatible with windshields and Snorkel Kit
- EPI Bushing Kit, steel inner, plastic outer bushings and shims Set of 4 Fits: Can Am ATV’s Outlander or Renegade and Commander If you are unsure on fitment, please contact us before purchasing! Exact replacement components to return your suspension to like-new condition Kits are sold per A-arm EPI Part Number: WE341043 P/U Part Number: 0430-0707 Replaces OEM Part Numbers: 706200051 706200181 706200157 Ships as Pictured
- OUT OF STOCKNew Genuine OEM G2 2017+ Outlander Steering Stem for DPS Part Number: 703501108 Old Part Number 709401750 Fits 2017+ Outlanders and 2018+ Renegades with DPS Comes as Pictured
- SHIPS FREE TO THE LOWER 48 STATES New OEM Standard G2 Rear Differential Ring & Pinion Gear Set 1652 There are a few options for kits, please verify your differential uses this style of gears before ordering! This will only fit six mounting hole differentials. OEM Rear Differential Gear set 10/36 Ring and Pinion gear set. The gears are straight cut as pictured. Open up the differential! Check for two bearings total (one on each side) on the ring gear. If you only have two proceed to the next measurement. Measure your outer diameter of your axle seals! They should measure close to 2 1/16? (52mm) To further verify fitment you can measure your pinion pilot shaft, this should be 5/8? (16mm) Please take the time to measure your parts before buying this will save time and restocking fees. Fits 2015 -2019 G2 style ATV 500/570/650/800/850/1000/1000R NON-XMR style REAR differential. 570/650 XMR machines do not have the true XMR differential.
There are a few options for kits, please verify your differential uses this style of gears before ordering!
This will only fit six mounting hole differentials.
Late G1 Early G2 Standard Rear Differential Ring 36t and Pinion 10t gear set Pinion bolt size is M10, this may be different than what you are replacing.
OEM Rear Differential Gear set 10/36 Ring and Pinion gear set. The gears are straight cut as pictured. This kit should be installed by an experienced technician.
Open up the differential! Check for two bearings total (one on each side) on the ring gear. If you only have two proceed to the next measurement. Measure your outer diameter of your axle seals! They should measure close to 1 3/4? (47mm) To further verify fitment you can measure your pinion pilot shaft, this should be 9/16" (14mm) The pictures show this very clearly. Please take the time to measure your parts before buying this will save time and restocking fees.
- 2012-2018 G2 ATV Rear Differential Swap Kit Kit includes: Rear Differential, Rear driveshaft, Bolt and Washer. This kit includes a rear differential with: Tapered roller bearings Three bearings on the pinion gear 6 inch diameter ring gear Your choice of gear style, spiral bevel or straight cut. Both have the same 3.60 ratio as your current differential. Spiral Bevel Gears are sourced from the 2013-18 800 850 and 1000 XMR differentials. Current part number 705502546 Old part numbers: 705502178 & 705502090 Straight Cut gears are sourced from the 2019+ 650+ differentials. Current part number 705502808 The driveshaft included is an OEM shaft with the correct end yokes for your application. The differential end yoke will not use a wear ring, this has been done away with by BRP the yoke is what the pinion seal touches now. You will need to fill the differential with 250ml (8.4oz) of 75W-140 gear oil and transfer over your fill plug and washer. The torque spec on the driveshaft retaining bolt is 55ftlbs with thread locker applied. Some minor trimming on the brackets that surround the differential is required. These differentials have the provision for an ABS sensor, this is standard on euro models, for mud riders state side, you can fill this hole with RTV or leave it open. If you are running the silver protector ring on your axle, you will need to push the ring outward slightly. We choose to remove these dust covers as they tend to trap debris when run under water.
OEM Snorkel kit, this raises the engine air intake well above the handlebars. The ECU is relocated to allow for CVT breather tubes to extend upward. This kit includes the brackets for the two plug type ECU found on ride by wire outlanders. With the tubes molded specifically for this application this is the cleanest kit you can install on your machine. Part number 715005999 Installation time is approximately 3.5 hours This snorkel kit is not compatible with the XT Handlebar Protector Kit (P/N 715000271) 715005999 instructions
- Can-Am 703500865 Secondary Clutch Driven Pulley Stud Nut Screw Kit Secondary Stud/Nut Kit M10x136mm You will need to reuse your washer. This kit will work on every Vtwin ATV factory driven (secondary) clutch (pulley) Also fits Commander driven clutch Will work on non QRS Maverick driven clutch If you have fitment questions, please contact us, we are here to help. Part numbers: 703500865 420441900 420242097 420242402