Can-am Outer CVT Cover, belt box. This is the updated 13 bolt cover. Works with 7 or 13 bolt inner covers. This will fit on any 2006-current v twin ATV, Renegade or Outlander, 500 650 800 or 1000. If you have a a stud with a nut retaining your primary clutch this cover does not have the depth needed. Many 1000R machines use a stud/nut in place of the bolt. Unsure on fitment, please ask! This will keep the water out! 13 Cover bolt holes Current Part number is: 420611397 Replaces: 420611395, 420611390, 420611391, 420611393
- SHIPS FREE TO THE LOWER 48 STATES Late G1 Early G2 Standard Rear Differential Bearing and Seal Kit High quality aftermarket bearings along with double lip axle seals. Bearing and Seal Brands include: Nachi, KOYO, NTN, Timken The large case sealing and pinion gear O-rings are NOT included as a cost saving measure, these O-rings are reusable if not damaged. There are a few options for kits, please verify your differential uses this style of gears before ordering! This will only fit six mounting hole differentials. Open up the differential! Check for two bearings total (one on each side) on the ring gear. If you only have two proceed to the next measurement. Measure your outer diameter of your axle seals! They should measure close to 1 3/4" (47mm) To further verify fitment you can measure your pinion pilot shaft, this should be 9/16″ (14mm) The last pictures show this very clearly. Please take the time to measure your parts before buying this will save time and restocking fees.
OEM Radiator Relocate Kit. This moves your radiator (not included) up on your front rack. This is a must for tackling extreme mud conditions where you risk clogging your radiator and overheating your engine! Allows for easy servicing (cleaning) This is a factory OEM kit, not an aftermarket kit, instructions are provided on BRP’s website. Coolant overflow tank is included, hoses ect.. You will not find a better fit and finish kit on the market. There is drilling and cutting involved. This is all covered in great detail. Roughly 3.5 hour install time This kit fits G2 and G2L models check out the pictured fitment chart if you are unsure what you ride. The white “can-am” is a protective film that can be removed with a small pick. Part number 715001930
- NEW Genuine Can-am Rear Prop Shaft for G1 STD single seat machines WILL NOT FIT MAX. This will work with 2006-2011 500 650 800 800R, Outlander or Renegade and 2012 Outlander 500 650 or Renegade 500. The picture is what you will get. We install the wear ring and deflector ring for fast install. Current Part number: 703500801 Previous numbers: 703500767 703500719 705500816 703500704
Set of four Bronco gas shock kit for G1 Outlander 650/800 or Renegade 500/800
These shocks are the same length on all four corners, you may notice a slight lift, more so on a well used machine.
*Please note these will not work in place of struts found on the Outlander 400/500 machines.
Features:
Bronco gas shocks offer long term consistent performance over stock oil only damped shocks
10% stiffer springs provide a better ride and higher load capacity
Works great on the front to better support your snowplow and on the rear when hauling cargo
Smooth black color blends perfectly on your machine
Direct bolt-on replacement: pre-installed spring allows for quicker setupP/N AU04414X4
Used ECM (computer) with OEM Digital Key.
This pair is tested, cleared of any codes and run on our shop ATV before leaving.
Your Dash (speedometer) may need to be paired with BUDS. If you want to start and run the machine simply unplug the dash before installing the ecu. We provide the pairing service free of charge with purchase of ECU or Dash, contact us for further details.
Only fits Generation 1 bikes Outlander and Renegade 800 HO 2006 2007 2008
Part Number: 420266374 420266623 710000817
- Air Pressure sensor, this goes in the Black plastic Intake manifold. Will work on any 2006 to current Can am Outlander, Renegade, Commander, Maverick, Defender 500 570 650 800 850 1000 XT XMR MAX or XXC The Manifold Absolute Pressure sensor or MAP sensor is a sensor that is attached to the intake manifold. The MAP sensor responds to changes in the intake manifold pressure (vacuum) and provides a reading of engine load. How it works is 5 volts DC is supplied to the sensor from the ECU. Inside the MAP sensor there is a resistor that moves in relation to intake manifold pressure. The resistor varies the voltage between about 1V to 4.5V (depending on engine load) and that voltage signal is returned to the PCM to indicate manifold pressure (vacuum). This signal is essential for the PCM to determine fuel delivery. Part numbers: 420874650 707000564 707000995 0 261 230 030 ALFA ROMEO 46553045 ALFA ROMEO 46533518 CHERY S21-3614021 FIAT 46553045 FIAT 77364869 FIAT 7084986 FIAT 0000046553045 FIAT 46533518 LANCIA 46533518 LANCIA 0000046553045 LANCIA 46553045 MOOSE 2120-0994 PROTON PW810694 ROTAX (BOMBARDIER-ROTAX GMBH) 874 650 SCANIA 5166434
- OUT OF STOCK
Sliding Sheave for CVTech Canam Clutches
Part Number 0910-0006