- OUT OF STOCK
NEW Outsiders Mud Crew Airbox seal This is an improved design over factory Apply a small amount of grease to aid install, this is much thicker and denser than the OEM o-ring or gasket Replaces OEM part numbers: 293300165 293300175 293300179 
MOOSE RACING HARD-PARTS Replacement Tie-Rod Ends 0430-0717 WILL NOT WORK WITH OEM TIE RODS Fits G2 ATV 2012-2018 with upgraded 12mm tie rods kit part number 0430-0674 This kit includes a pair of 12mm LH and RH ends, enough to repair one side of your ATV.
All Balls complete fuel pump module, retaining nut and gasket This fits G1 Models: 2009-2015 EFI Outlander 400 2009-2012 Outlander or Renegade 500 2009-2012 Outlander 650 2009-2011 Outlander 800R 2012 Outlander 800R XMR 2012 Outlander 800R MAX 2009-2011 Renegade 800R Part number: 47-1049 24-71022 Replaces OEM numbers: 703500766 703500781 709000194 709000245
Part number 0950-1011
This isolates the spring from the one way bearing on a trail bloc primary clutch.
Measurements as shown
Updated Can-am Rear G2 Driveshaft Fits: 2019+ Outlander 1000R (excluding MAX and XMR) 2019+ Outlander 650/850 (excluding MAX) 2019+ Renegade 650/850 All new all OEM Shaft OEM U-joints. OEM protector ring installed Gearbox side yoke swapped to 18 spline Current Part number: 703500988 Previous Part number: 703500858 703500931 If you have a 2019+ 570 short wheel base single rider, this may be the correct shaft for your application, the parts fiche may not show the correct part number. You will need to measure the outer diameter of your rear differential's pinon seal, this shaft will only work with machines that have a 80mm pinion seal. If you measure 70mm you will need 703500986. 20 spline differential side yoke (fits 705502808/705502546 rear differential) 18 spline gearbox side yoke (small gearbox size) No wear ring needed, the deferential side yoke is machined to the outer diameter that a wear ring would be.
SHIPS FREE TO THE LOWER 48 STATES OEM BRP Heated Grips and Thumb kit.- LED dimmer facilitates reading temperature settings. 4 temperature settings with individual controls for thumb and grips. Returns to previous heat setting. One-touch shutdown. Compatible with Intelligent Throttle Control (ITC). Wiring Cable (710004567) is required for installation on G2 650 and G2L 570.
NEW OEM Mode Switch Menu/Trip Found on 2020+ Outlander 850 1000R Part number 710006717
All Balls complete module, retaining nut and gasket This fits many G2 model ATVs please contact us if you have fitment questions. Part number: 1009-0139 47-1024 Replaces OEM numbers: 709000287 709000758
Brand New Moose Utility 13 Bolt CVT Cover Gasket
Works on 7 bolt covers also.
Part number 0935-1193
replaces: 420430127 420430126 420430124 420430123 420430120
NEW extra firm G1 outlander 500 650 800 800R seat foam. Use with seat part numbers 715500323 708000756 708000507 708000402 708001649 This is just the foam, no cover or pan.
Rugged wheels spacers are made from T6061 aluminum alloy and are precisely CNC machined for accurate dimensions. Spacers can be direct bolt on and can use OEM studs. If you are looking to widen the stance of your machine, clear larger tires or get some new wheels. These spacers are just what you need. These spacers are sold as a pair. One inch thick The bolt pattern is 4x137mm M10 studs Part number PAWS-1035
Rugged wheels spacers are made from T6061 aluminum alloy and are precisely CNC machined for accurate dimensions. Spacers can be direct bolt on and can use OEM studs. If you are looking to widen the stance of your machine, clear larger tires or get some new wheels. These spacers are just what you need. These spacers are sold as a pair. 1.5 inch thick The bolt pattern is 4x137mm M10 studs Part number PAWS-1036
Rugged wheels spacers are made from T6061 aluminum alloy and are precisely CNC machined for accurate dimensions. Spacers can be direct bolt on and can use OEM studs. If you are looking to widen the stance of your machine, clear larger tires or get some new wheels. These spacers are just what you need. These spacers are sold as a pair. Two inch thick The bolt pattern is 4x137mm M10 studs Part number PAWS-1037
NEW OEM BRP Coupler This is found on many machines, 18 spline exterior No need for a wear ring on this coupler. Part number 705401969 Replaces 703500678 705400149 705500201
New OEM BRP secondary spring. Found on many 1000/1000R and 850 models. Current Part number 420638040 Replaces 420238177
New NGK Spark Plug 93444
OEM part number 715900352
NGK part number LMAR8D-J
These spark plugs work in 2015+ Outlander/Renegade 450 850 and 1000R also fits Defender HD5
Shell
Thread Diameter: 10mm
Thread Pitch: 1.0mm
Seat Type: Gasket
Reach: 26.5mm (1.04″)
Hex Size: 9/16″ (14mm)
Terminal Type: Solid
Gap: .031″ (0.8mm)Center Electrode
Material: Nickel
Type: Standard
Size: 2.5mm
Projection: ProjectedGround Electrode
Material: Nickel
Type: Multi-GroundSpecifications
Resistor: Yes
Resistor Value: 5k Ohm
Heat Range: 8
Torque Specs: Aluminum: 7.2-8.7 lb. ft.
NEW OEM Shock Bushing for base black body hydraulic type shocks. These will fit: 2020 and prior Commanders 800 800R 1000 1000R G1/G2 Outlanders 400 450 500 570 650 800HO 800R 850 1000 1000R Oem part number 715900122
BOYESEN SUPERCOOLER WATER PUMP Cover and Impeller Kit Increased coolant flow at all rpm ranges Patented Nautilus-style impeller for hydrodynamic efficiency Color/Finish: Black, Powder-Coated Material: Aluminum Model: Supercooler Part number 850709 WPK-80AB Replaces OEM 420822750, 420622020 and 420622022 This is the style with the larger output nipple roughly 1 inch in outer diameter.
NEW Speed Sensor Quad Logic brand Will fit 2006-Current Outlander, Renegade, Maverick, Maverick X3, Commander, and Defenders 2210-0568 500-1024 Replaces OE Numbers 420265621, 420265622, 420265624, 420265625, 420265626, 420265629, 707000745 and 711265622
Connecting Rod Bolt for 650 800 V twin Engines This is the OEM bolt with a size of M8x1 Part number 420641640 420641645
Can Am G2 2012-2018 Outlander XT XTP bumper cap kits Will not fit G1 or G2L models, questions on fitment? Please ask! Comes with 1 Front LEFT or RIGHT Rear cap 1 Backing plate 2 Torx screws Will only work on front right or left rear of machine as you sit on it. All parts are New OEM Part Numbers: 705004409 705004987 250000720
Made in the USA Specialized ATV, made some strong, tough rods that will hold up to whatever kind of riding you like. 6061 Billet Rods with 5/8 heim joints and all the needed hardware to install. 1 set comes with 2 tie rods and complete assembled heims and hardware. Fits G2 Outlanders and Renegades 2012+ (even the wider 2019+ machines)
Specialized ATV HD Front Drive Shaft
Fits G2 ATVs
Replaces OEM part numbers: 705400913 705401032
Ships as pictured
25mm diameter shaft, this is huge compared to the OEM part.
MADE IN USA
CVtech Trail Bloc Primary Clutch with HD retaining bolt, calibrations are for ATVs not UTVs Solid upgrade over the factory unlocked primary clutch, this is a straight bolt on replacement. Locked sheaves, smaller one-way diameter and more belt grip. This is a great clutch for riders looking for a performance upgrade. This comes preset, some fine tuning may be required to get this 100% Many find these settings to be spot on. We will provide assistance in fine tuning for your riding style. Please allow additional 1-2 day handling time.
Have Questions?
Our staff is available to answer questions
canampartsguy@gmail.com
1340 Okray Ave.
Plover, WI 54467
jared@canampartsguy.com
Cant find What you're looking for?
Visit our 
store!
2016 Can Am Parts, LLC. All rights reserved.