- Dash/Speedometer for G2 500/650/800/1000 bikes. This is the factory Gauge/Screen. for 2012 2013 G2 models. The dash is designed to auto pair, but sometimes it will not auto pair and you will have to program them together with buds software. This can be done at your local dealer or you can send in your ecu, key(s), and DPS (power steering) to us for programming. Contact for more information. It will display 0 miles, please record your current miles for your records. Current Part Number 710003103 Replaces Part Number 710002696 Will NOT fit 2013 Outlander 650 XMR
There are a few options for kits, please verify your differential uses this style of gears before ordering!
This will only fit six mounting hole differentials.
Late G1 Early G2 Standard Rear Differential Ring 36t and Pinion 10t gear set Pinion bolt size is M10, this may be different than what you are replacing.
OEM Rear Differential Gear set 10/36 Ring and Pinion gear set. The gears are straight cut as pictured. This kit should be installed by an experienced technician.
Open up the differential! Check for two bearings total (one on each side) on the ring gear. If you only have two proceed to the next measurement. Measure your outer diameter of your axle seals! They should measure close to 1 3/4? (47mm) To further verify fitment you can measure your pinion pilot shaft, this should be 9/16″ (14mm) The pictures show this very clearly. Please take the time to measure your parts before buying this will save time and restocking fees.
- 1652 G2 Standard Rear Differential Rebuild Kit Please note, application alone is not accurate enough, please measure your parts before ordering! There are a few options for rebuild kits, please measure your parts before ordering!! OEM Rear Differential Gear set 10/36 Ring and Pinion gear set. The gears are straight cut as pictured. Paired with high quality aftermarket ball bearings along with double lip axle seals. If your differential has tapered roller bearings, this will not fit. This kit should be installed by an experienced technician. Shims are included as the gears will need to be set up in your cases. Note: the O rings are not included, this is a cost savings measure as they are generally reusable. This kit will only fit six mounting hole differentials. Measure your outer diameter of the pinion seal, it should measure 2 3/4" (70mm) Measure your outer diameter of your axle seals! They should measure close to 2 1/16″ (52mm) To further verify fitment you can measure your pinion pilot shaft, this should be 5/8″ (16mm) Please take the time to measure your parts before buying this will save time and restocking fees. Fits 2015 and newer G2 style ATV 500/570/650/800/850/1000/1000R NON-XMR style REAR differential. 570/650 XMR machines do not have the true XMR differential.
- OUT OF STOCKSHIPS FREE TO THE LOWER 48 STATES New OEM XMR Rear Differential Gear set, 10/36 Ring and Pinion gear set, Timken, Dichtomatik or SKF seals, NTN or IKO pilot bearing , OEM shim kit and OEM bearings Fits the larger style 800/850/1000/1000R XMR style REAR differential first seen on the 2013 Outlander 1000 XMR. This gear set will not install into 650 xmr and 570 xmr differential cases. Please see our other listings for those. This is a common part to swap on to generation 2 atvs. We do sell complete kits to do so, please check out our other listings. Part number 703500870
- OUT OF STOCKNew OEM 2019+ rear differential gear set, 10/36 tooth straight cut ring and pinion gear set, Timken seals, NTN or IKO pilot bearing , OEM shim kit and OEM bearings along with a new bolt and washer to retain the driveshaft. BRP claims 25% increase in load capacity on this gear set vs the spiral cut xmr final drive units (rear differentials) from 13-18 models. Fits differential part numbers: 705502808, 705502546, 705502178, 705502090 703501031 705501550 705501556 705501557
- OUT OF STOCKG2 dual piston brake calipers with pads. Genuine OEM parts. This set of three calipers will fit G2 Renegade and Outlander 2012+ Part numbers 705600861 705600862 705600859 Cleaned greased and ready to install.
- SHIPS FREE TO THE LOWER 48 STATES Late G1 Early G2 Standard Rear Differential Rebuild Kit There are a few options for rebuild kits, please measure your parts before ordering!! OEM Rear Differential Gear set 10/36 Ring and Pinion gear set. The gears are straight cut as pictured. Paired with high quality aftermarket bearings along with double lip axle seals. This kit should be installed by an experienced technician. Ring gear shims are included as the gears will need to be set up in your cases, the pinion shims should remain unchanged Note: the O rings are not included, this is a cost savings measure as they are generally reusable. There are a few options for kits, please verify your differential uses this style of gears before ordering! This will only fit six mounting hole differentials. Open up the differential! Check for two bearings total (one on each side) on the ring gear. If you only have two proceed to the next measurement. Measure your outer diameter of your axle seals! They should measure close to 1 3/4" (47mm) To further verify fitment you can measure your pinion pilot shaft, this should be 9/16? (14mm) The last pictures show this very clearly. Please take the time to measure your parts before buying this will save time and restocking fees.
OEM Radiator Relocate Kit. This moves your radiator (not included) up on your front rack. (will not fit 22+ XXC models) This is a must for tackling extreme mud conditions where you risk clogging your radiator and overheating your engine! Allows for easy servicing (cleaning) This is a factory OEM kit, not an aftermarket kit, instructions are provided on BRP’s website. Coolant overflow tank is included, hoses ect.. You will not find a better fit and finish kit on the market. There is drilling and cutting involved. This is all covered in great detail. Roughly 3.5 hour install time This kit fits G2 and G2L models check out the pictured fitment chart if you are unsure what you ride. The white “can-am” is a protective film that can be removed with a small pick. Part number 715001930
- OUT OF STOCKOEM Snorkel kit, this raises the engine air intake well above the handlebars. The ECU is relocated to allow for CVT breather tubes to extend upward. This kit includes the brackets for the two plug type ECU found on ride by wire outlanders. With the tubes molded specifically for this application this is the cleanest kit you can install on your machine. Part number 715005999 Installation time is approximately 3.5 hours This snorkel kit is not compatible with the XT Handlebar Protector Kit (P/N 715000271)